• There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

ASTM B 308/B308M : 2020

Current
Current

The latest, up-to-date edition.

Standard Specification for Aluminum-Alloy 6061-T6 Standard Structural Profiles
Available format(s)

Hardcopy , PDF

Language(s)

English

Published date

14-01-2020

1.1This specification2 covers extruded 6061-T6 aluminum-alloy standard structural profiles.

1.2The profiles are limited to I-beams, H-beams, channels, angles, tees, and zees.

Note 1:For other extruded profiles in other alloys and tempers refer to Specification B221.

1.3Alloy and temper designations are in accordance with ANSI H35.1/H35.1(M). The equivalent Unified Numbering System alloy designation is that in Table 1 preceded by A9, or A96061 for alloy 6061 in accordance with Practice E527.

1.4For acceptance criteria for inclusion of new aluminum and aluminum alloys in this specification, see Annex A2.

1.5The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

1.6This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.7This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Committee
B 07
DocumentType
Standard
Pages
6
ProductNote
This standard is also refers to Fed. Std. No. 123.
PublisherName
American Society for Testing and Materials
Status
Current
SupersededBy
Supersedes

ASTM D 2649 : 2020 : REV A Standard Test Method for Corrosion Characteristics of Solid Film Lubricants
ASTM C 1802 : 2020 Standard Specification for Design, Testing, Manufacture, Selection, and Installation of Horizontal Fabricated Metal Access Hatches for Utility, Water, and Wastewater Structures

ASTM B 557 : 2015 : R2023 Standard Test Methods for Tension Testing Wrought and Cast Aluminum- and Magnesium-Alloy Products
ASTM B 557M : 2015 : R2023 Standard Test Methods for Tension Testing Wrought and Cast Aluminum- and Magnesium-Alloy Products (Metric)
ASTM B 648 : 2010 : R2015 : EDT 1 Standard Test Method for Indentation Hardness of Aluminum Alloys by Means of a Barcol Impressor
ASTM E 29 : 2013 : R2019 Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications
ASTM B 557M : 2002 Standard Test Methods of Tension Testing Wrought and Cast Aluminum- and Magnesium-Alloy Products [Metric]
ASTM E 18 : 2022 Standard Test Methods for Rockwell Hardness of Metallic Materials
ASTM E 716 : 2016 : R2021 : EDT 2 Standard Practices for Sampling and Sample Preparation of Aluminum and Aluminum Alloys for Determination of Chemical Composition by Spark Atomic Emission Spectrometry
ASTM E 29 : 2002 Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications
ASTM B 660 : 2021 Standard Practices for Packaging/Packing of Aluminum and Magnesium Products
ASTM E 716 : 2016 : R2021 Standard Practices for Sampling and Sample Preparation of Aluminum and Aluminum Alloys for Determination of Chemical Composition by Spark Atomic Emission Spectrometry
ASTM E 18 : 2020 Standard Test Methods for Rockwell Hardness of Metallic Materials
ASTM B 648 : 2023 Standard Test Method for Indentation Hardness of Aluminum Alloys by Means of a Barcol Impressor
ASTM B 221 : 2020 Standard Specification for Aluminum and Aluminum-Alloy Extruded Bars, Rods, Wire, Profiles, and Tubes
ASTM E 527 : 2023 Standard Practice for Numbering Metals and Alloys in the Unified Numbering System (UNS)
ASTM D 3951 : 2018 Standard Practice for Commercial Packaging
ASTM E 716 : 2016 Standard Practices for Sampling and Sample Preparation of Aluminum and Aluminum Alloys for Determination of Chemical Composition by Spark Atomic Emission Spectrometry
ASTM B 557 : 2015 Standard Test Methods for Tension Testing Wrought and Cast Aluminum- and Magnesium-Alloy Products
ASTM D 3951 : 2018 : R2023 Standard Practice for Commercial Packaging
ASTM E 527 : 2016 Standard Practice for Numbering Metals and Alloys in the Unified Numbering System (UNS)
ASTM B 557M : 1994 Standard Test Methods of Tension Testing Wrought and Cast Aluminum- and Magnesium-Alloy Products [Metric]
ASTM B 660 : 2015 Standard Practices for Packaging/Packing of Aluminum and Magnesium Products
ASTM B 660 : 2023 Standard Practices for Packaging/Packing of Aluminum and Magnesium Products
ASTM E 18 : 2019 Standard Test Methods for Rockwell Hardness of Metallic Materials
ASTM B 557 : 1994 Standard Test Methods of Tension Testing Wrought and Cast Aluminum- and Magnesium-Alloy Products
ASTM B 647 : 2010 : R2016 Standard Test Method for Indentation Hardness of Aluminum Alloys by Means of a Webster Hardness Gage
ASTM B 557M : 2015 Standard Test Methods for Tension Testing Wrought and Cast Aluminum- and Magnesium-Alloy Products (Metric)
ASTM E 716 : 2016 : R2021 : EDT 1 Standard Practices for Sampling and Sample Preparation of Aluminum and Aluminum Alloys for Determination of Chemical Composition by Spark Atomic Emission Spectrometry
ASTM B 221 : 2002 Standard Specification for Aluminum and Aluminum-Alloy Extruded Bars, Rods, Wire, Profiles, and Tubes
ASTM B 647 : 2023 Standard Test Method for Indentation Hardness of Aluminum Alloys by Means of a Webster Hardness Gage
ASTM E 29 : 2022 Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications
ASTM B 221 : 2021 Standard Specification for Aluminum and Aluminum-Alloy Extruded Bars, Rods, Wire, Profiles, and Tubes

View more information
£52.59
Excluding VAT

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.