Standard Specification for Nickel-Molybdenum Alloy Rod

Available format(s)

Hardcopy , PDF

Language(s)

English

Published date

01-11-2018

Publisher

American Society for Testing and Materials

CONTAINED IN VOL. 02.04, 2015 Defines rod of nickel-molybdenum alloys (UNS N10001, N10665, N10675, N10629, and N10624) for use in general corrosive service.

1.1This specification2 covers rod of nickel-molybdenum alloys (UNS N10001, N10665, N10675, N10629, and N10624)3 as shown in Table 1, for use in general corrosive service.

1.2The following products are covered under this specification:

1.2.1Rods ⁵/₁₆to ³/₄in. (7.94 to 19.05 mm) excl in diameter, hot or cold finished, solution annealed and pickled or mechanically descaled.

1.2.2Rods ³/₄to 3¹/₂in. (19.05 to 88.9 mm) incl in diameter, hot or cold finished, solution annealed, ground or turned.

1.3The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use.

1.5This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Committee	B 02
DocumentType	Standard
Pages	4
ProductNote	Reconfirmed 2003
PublisherName	American Society for Testing and Materials
Status	Current
Supersedes	ASTM B 335 : 2003 : R2013

ASTM E 8/E8M : 2024	Standard Test Methods for Tension Testing of Metallic Materials
ASTM E 8/E8M : 2016 : REV A : EDT 1	Standard Test Methods for Tension Testing of Metallic Materials
ASTM E 29 : 2013 : R2019	Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications
ASTM E 1473 : 2009	Standard Test Methods for Chemical Analysis of Nickel, Cobalt, and High-Temperature Alloys
ASTM E 8/E8M : 2021	Standard Test Methods for Tension Testing of Metallic Materials
ASTM E 1473 : 1994 : REV A : R1998	Standard Test Methods for Chemical Analysis of Nickel, Cobalt, and High-Temperature Alloys
ASTM E 29 : 2002	Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications
ASTM E 1473 : 2003	Standard Test Methods for Chemical Analysis of Nickel, Cobalt, and High-Temperature Alloys
ASTM E 1473 : 2016 : REDLINE	Standard Test Methods for Chemical Analysis of Nickel, Cobalt and High-Temperature Alloys
ASTM E 1473 : 2022	Standard Test Methods for Chemical Analysis of Nickel, Cobalt, and High-Temperature Alloys
ASTM E 8/E8M : 2022	Standard Test Methods for Tension Testing of Metallic Materials
ASTM E 1473 : 1994 : REV A : R2003	Standard Test Methods for Chemical Analysis of Nickel, Cobalt, and High-Temperature Alloys
ASTM E 55 : 2023	Standard Practice for Sampling Wrought Nonferrous Metals and Alloys for Determination of Chemical Composition
ASTM E 8 : 2004	Standard Test Methods for Tension Testing of Metallic Materials
ASTM E 1473 : 2016	Standard Test Methods for Chemical Analysis of Nickel, Cobalt and High-Temperature Alloys
ASTM E 55 : 2011 : R2017	Standard Practice for Sampling Wrought Nonferrous Metals and Alloys for Determination of Chemical Composition
ASTM E 55 : 2011 : R2022 : EDT 1	Standard Practice for Sampling Wrought Nonferrous Metals and Alloys for Determination of Chemical Composition
ASTM E 29 : 2022	Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications