We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
  • ASTM B 505/B505M : 2018

    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    Add to Watchlist
    This Standard has been added successfully to your Watchlist.
    Please visit My Watchlist to see all standards that you are watching.
    Please log in or to add this standard to your Watchlist.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    You need to be logged in to add this standard to your Watchlist.
    Please log in now or create an account to add.
    You already added this Product in the Watchlist.

    Standard Specification for Copper Alloy Continuous Castings

    Available format(s):  Hardcopy, PDF

    Superseded date:  08-11-2022

    Language(s):  English

    Published date:  26-03-2018

    Publisher:  American Society for Testing and Materials

    Add to Watchlist

    Add To Cart

    Abstract - (Show below) - (Hide below)

    This specification establishes requirements for continuously cast rod, bar, tube, and shapes produced from copper alloys with nominal compositions as listed in Table 1.2

    Scope - (Show below) - (Hide below)

    1.1This specification establishes requirements for continuously cast rod, bar, tube, and shapes produced from copper alloys with nominal compositions as listed in Table 1.2

    (A)Antimony 0.07, Boron 0.001.

    1.2Castings produced to this specification may be manufactured for and supplied from stock. In such cases the manufacturer shall maintain heat traceability to specific manufacturing date and chemical analysis.

    1.3The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

    1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

    1.5This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

    General Product Information - (Show below) - (Hide below)

    Committee B 05
    Document Type Standard
    Publisher American Society for Testing and Materials
    Status Superseded
    Superseded By
    Supersedes

    Standards Referenced By This Book - (Show below) - (Hide below)

    ASTM F 1718 : 2001 : R2019 Standard Specification for Rotary Positive Displacement Distillate Fuel Pumps
    ASTM B 824 : 2017 Standard Specification for General Requirements for Copper Alloy Castings
    ASTM F 2798 : 2009 : R2018 Standard Specification for Sealless Lube Oil Pump with Oil Through Motor for Marine Applications
    ASTM F 998 : 2012 : R2022 Standard Specification for Centrifugal Pump, Shipboard Use

    Standards Referencing This Book - (Show below) - (Hide below)

    ASTM B 208 : 2014 Standard Practice for Preparing Tension Test Specimens for Copper Alloy Sand, Permanent Mold, Centrifugal, and Continuous Castings
    ASTM E 8/E8M : 2016 : REV A : EDT 1 Standard Test Methods for Tension Testing of Metallic Materials
    ASTM E 8/E8M : 2021 Standard Test Methods for Tension Testing of Metallic Materials
    ASTM E 18 : 2022 Standard Test Methods for Rockwell Hardness of Metallic Materials
    ASTM E 10 : 2001 Standard Test Method for Brinell Hardness of Metallic Materials
    ASTM E 18 : 2020 Standard Test Methods for Rockwell Hardness of Metallic Materials
    ASTM E 255 : 1991 : R1997 Standard Practice for Sampling Copper and Copper Alloys for the Determination of Chemical Composition
    ASTM E 8/E8M : 2022 Standard Test Methods for Tension Testing of Metallic Materials
    ASTM B 208 : 2014 : R2021 Standard Practice for Preparing Tension Test Specimens for Copper Alloy Sand, Permanent Mold, Centrifugal, and Continuous Castings
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective