• There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

ASTM C 1193 : 2011

NA
NA

Status of Standard is Unknown

Standard Guide for Use of Joint Sealants
Available format(s)

Hardcopy , PDF

Language(s)

English

Published date

15-06-2011

1.1 This guide describes the use of a cold liquid-applied sealant for joint sealing applications. Including joints on buildings and related adjacent areas, such as plazas, decks, and pavements for vehicular or pedestrian use, and types of construction other than highways and airfield pavements and bridges. Information in this guide is primarily applicable to a single and multi-component, cold liquid-applied joint sealant and secondarily to a precured sealant when used with a properly prepared joint opening and substrate surfaces.

1.2 An elastomeric or non-elastomeric sealant described by this guide should meet the requirements of Specification C834, C920, or C1311.

1.3 This guide does not provide information or guidelines for the use of a sealant in a structural sealant glazing application. Guide C1401 should be consulted for this information. Additionally, it also does not provide information or guidelines for the use of a sealant in an insulating glass unit edge seal used in a structural sealant glazing application. Guide C1249 should be consulted for this information.

1.4 Practice C919 should be consulted for information and guidelines for the use of a sealant in an application where an acoustic joint seal is required.

1.5 This guide also does not provide information relative to the numerous types of sealant that are available nor specific generic sealant properties, such as hardness, tack-free time, or curing process, among others.

1.6 The values stated in SI units are to be regarded as the standard. The values given in parenthesis are provided for information only.

1.7 The Committee with jurisdiction for this standard is not aware of any comparable standards published by other organizations.

1.8 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use.

1.9 The committee with jurisdiction over this standard is not aware of any comparable standards published by other organizations.

Committee
C 24
DocumentType
Guide
Pages
33
PublisherName
American Society for Testing and Materials
Status
NA
SupersededBy
Supersedes

ASTM E 241 : 2009 : R2014 : EDT 1 Standard Guide for Limiting Water-Induced Damage to Buildings
ASTM C 920 : 2018 Standard Specification for Elastomeric Joint Sealants
ASTM C 1127/C1127M : 2015 Standard Guide for Use of High Solids Content, Cold Liquid-Applied Elastomeric Waterproofing Membrane with an Integral Wearing Surface
ASTM C 1521 : 2013 Standard Practice for Evaluating Adhesion of Installed Weatherproofing Sealant Joints
ASTM C 834 : 2017 Standard Specification for Latex Sealants
ASTM C 1253 : 2014 : R2019 Standard Test Method for Determining the Outgassing Potential of Sealant Backing
ASTM C 1311 : 2014 Standard Specification for Solvent Release Sealants
ASTM C 1242 : 2019 Standard Guide for Selection, Design, and Installation of Dimension Stone Attachment Systems
ASTM C 919 : 2019 Standard Practice for Use of Sealants in Acoustical Applications
ASTM C 1736 : 2011 Standard Practice for Non-Destructive Evaluation of Adhesion of Installed Weatherproofing Sealant Joints Using a Rolling Device (Withdrawn 2020)
ASTM C 1564 : 2015 Standard Guide for Use of Silicone Sealants for Protective Glazing Systems
ASTM E 2112 : 2019 : REV B Standard Practice for Installation of Exterior Windows, Doors and Skylights
ASTM C 1401 : 2014 Standard Guide for Structural Sealant Glazing
ASTM C 981 : 2005 : R2013 Standard Guide for Design of Built-Up Bituminous Membrane Waterproofing Systems for Building Decks
ASTM C 1472 : 2016 Standard Guide for Calculating Movement and Other Effects When Establishing Sealant Joint Width
ASTM C 1481 : 2012 : R2017 Standard Guide for Use of Joint Sealants with Exterior Insulation and Finish Systems (EIFS)
ASTM C 898/C898M : 2009 : R2017 Standard Guide for Use of High Solids Content, Cold Liquid-Applied Elastomeric Waterproofing Membrane with Separate Wearing Course
ASTM E 2435 : 2005 : R2015 Standard Guide for Application of Engineering Controls to Facilitate Use or Redevelopment of Chemical-Affected Properties
ASTM C 717 : 2019 Standard Terminology of Building Seals and Sealants
ASTM E 2266 : 2011 Standard Guide for Design and Construction of Low-Rise Frame Building Wall Systems to Resist Water Intrusion

View more information
£90.16
Excluding VAT

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.