• There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

ASTM C 1435/C1435M : 2014 : REDLINE

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Standard Practice for Molding Roller-Compacted Concrete in Cylinder Molds Using a Vibrating Hammer
Available format(s)

PDF

Superseded date

17-06-2020

Language(s)

English

Published date

01-10-2014

CONTAINED IN VOL. 04.02, 2014 Defines molding cylindrical test specimens from concrete when the standard procedures of rodding and internal vibration, as described in Practice C 31/C31M and Practice C 1176, are not practicable, it is applicable to freshly-mixed concrete, prepared in the laboratory and the field.

1.1This practice2 covers molding cylindrical test specimens from concrete when the standard procedures of rodding and internal vibration, as described in Practice C31/C31M and Practice C1176/C1176M, are not practicable. This practice is applicable to freshly-mixed concrete, prepared in the laboratory and the field.

1.2Freshly-mixed concrete is molded in cylindrical molds using an electric vibrating hammer equipped with a shaft and circular plate.

1.3The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text, the inch-pound units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

1.4The text of this practice references notes and footnotes, which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of this practice.

1.5This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Committee
C 09
DevelopmentNote
Supersedes ASTM C 1435. (05/2005)
DocumentType
Redline
Pages
6
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy

ACI 233R : 2017 GUIDE TO THE USE OF SLAG CEMENT IN CONCRETE AND MORTAR
ACI 207.5R : 2011 REPORT ON ROLLER-COMPACTED MASS CONCRETE
ASTM C 1800/C1800M : 2016 Standard Test Method for Determining Density of Roller-Compacted Concrete Specimens Using the Gyratory Compactor
ASTM C 39/C39M : 2018 : REDLINE Standard Test Method for Compressive Strength of Cylindrical Concrete Specimens
ASTM C 1245/C1245M : 2012 : REDLINE Standard Test Method for Determining Relative Bond Strength Between Hardened Roller Compacted Concrete Lifts (Point Load Test)

ASTM C 470/C470M : 2015 : REDLINE Standard Specification for Molds for Forming Concrete Test Cylinders Vertically
ASTM C 496/C496M : 2017 : REDLINE Standard Test Method for Splitting Tensile Strength of Cylindrical Concrete Specimens
ACI 211.3 : 1992(R1997) SELECTING PROPORTIONS FOR NO-SLUMP CONCRETE
ASTM C 1176 : 2005 Standard Practice for Making Roller-Compacted Concrete in Cylinder Molds Using a Vibrating Table
ACI 207.5R : 2011 REPORT ON ROLLER-COMPACTED MASS CONCRETE

View more information
£62.61
Excluding VAT

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.