ASTM C 1516 : 2005 : R2017
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
Hardcopy , PDF
17-03-2023
English
06-04-2017
CONTAINED IN VOL. 04.01, 2017 Defines the minimum requirements and procedures for field application of Direct-applied Exterior Finish Systems (DEFS).
1.1This practice covers the minimum requirements and procedures for field application of Direct-applied Exterior Finish Systems (DEFS). Direct-applied exterior finish systems are coating systems applied over various substrates with non-metallic reinforcing mesh, in which the base coat ranges from not less than 1/16in. (1.6 mm) to 3/32in. (2.4 mm) in dry thickness, depending on the mass of the reinforcing mesh. This base coat is subsequently covered with a finish coat that is available in a variety of textures and colors.
1.2The values stated in inch-pound units are to be regarded as the standard. The metric values given in parentheses are approximate and are provided for information purposes only.
1.3This standard may involve hazardous materials, operations and equipment. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
1.4This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| Committee |
C 11
|
| DocumentType |
Standard Practice
|
| Pages |
7
|
| ProductNote |
Reconfirmed 2017
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| ASTM C 1325 : 2019 | Standard Specification for Fiber-Mat Reinforced Cementitious Backer Units |
| ASTM C 1278/C1278M : 2017 : REDLINE | Standard Specification for Fiber-Reinforced Gypsum Panel |
| ASTM C 1063 : 2014 : REV B | Standard Specification for Installation of Lathing and Furring to Receive Interior and Exterior Portland Cement-Based Plaster |
| ASTM E 1825 : 2006 : R2012 | Standard Guide for Evaluation of Exterior Building Wall Materials, Products, and Systems |
| ASTM C 1063 : 2015 : REV A | Standard Specification for Installation of Lathing and Furring to Receive Interior and Exterior Portland Cement-Based Plaster |
| ASTM C 1063 : 2016 : REV C | Standard Specification for Installation of Lathing and Furring to Receive Interior and Exterior Portland Cement-Based Plaster |
| ASTM C 1063 : 2015 | Standard Specification for Installation of Lathing and Furring to Receive Interior and Exterior Portland Cement-Based Plaster |
| ASTM C 1063 : 2019 : REV A | Standard Specification for Installation of Lathing and Furring to Receive Interior and Exterior Portland Cement-Based Plaster |
| ASTM C 1063 : 2012 : REV A | Standard Specification for Installation of Lathing and Furring to Receive Interior and Exterior Portland Cement-Based Plaster |
| ASTM C 1063 : 2013 | Standard Specification for Installation of Lathing and Furring to Receive Interior and Exterior Portland Cement-Based Plaster |
| ASTM C 1063 : 2018 : REV B | Standard Specification for Installation of Lathing and Furring to Receive Interior and Exterior Portland Cement-Based Plaster |
| ASTM C 1063 : 2014 | Standard Specification for Installation of Lathing and Furring to Receive Interior and Exterior Portland Cement-Based Plaster |
| ASTM E 1825 : 2017 | Standard Guide for Evaluation of Exterior Building Wall Materials, Products, and Systems |
| ASTM C 1186 : 1991 | Standard Specification for Flat Non-Asbestos Fiber-Cement Sheets |
| ASTM C 1063 : 2011 : REV B | Standard Specification for Installation of Lathing and Furring to Receive Interior and Exterior Portland Cement-Based Plaster |
| ASTM C 1063 : 2020 | Standard Specification for Installation of Lathing and Furring to Receive Interior and Exterior Portland Cement-Based Plaster |
| ASTM C 1325 : 2008 : REV B | Standard Specification for Non-Asbestos Fiber-Mat Reinforced Cementitious Backer Units |
| ASTM C 1063 : 2014 : REV C | Standard Specification for Installation of Lathing and Furring to Receive Interior and Exterior Portland Cement-Based Plaster |
| ASTM C 1063 : 2019 | Standard Specification for Installation of Lathing and Furring to Receive Interior and Exterior Portland Cement-Based Plaster |
| ASTM C 1325 : 2014 | Standard Specification for Non-Asbestos Fiber-Mat Reinforced Cementitious Backer Units |
| ASTM C 1325 : 1999 | Standard Specification for Non-Asbestos Fiber-Mat Reinforced Cement Interior Substrate Sheets |
| ASTM C 1063 : 2003 | Standard Specification for Installation of Lathing and Furring to Receive Interior and Exterior Portland Cement-Based Plaster |
| ASTM C 1063 : 2021 | Standard Specification for Installation of Lathing and Furring to Receive Interior and Exterior Portland Cement-Based Plaster |
| ASTM C 1063 : 2018 : REV A | Standard Specification for Installation of Lathing and Furring to Receive Interior and Exterior Portland Cement-Based Plaster |
| ASTM C 1063 : 2020 : REV A | Standard Specification for Installation of Lathing and Furring to Receive Interior and Exterior Portland Cement-Based Plaster |
| ASTM E 1825 : 1996 | Standard Guide for Evaluation of Exterior Building Wall Materials, Products, and Systems |
| ASTM C 1063 : 2018 | Standard Specification for Installation of Lathing and Furring to Receive Interior and Exterior Portland Cement-Based Plaster |
| ASTM E 1825 : 2017 : REDLINE | Standard Guide for Evaluation of Exterior Building Wall Materials, Products, and Systems |
| ASTM C 1325 : 2004 | Standard Specification for Non-Asbestos Fiber-Mat Reinforced Cement Substrate Sheets |
| ASTM C 1063 : 2011 : REV A | Standard Specification for Installation of Lathing and Furring to Receive Interior and Exterior Portland Cement-Based Plaster |
| ASTM C 1063 : 2014 : REV A | Standard Specification for Installation of Lathing and Furring to Receive Interior and Exterior Portland Cement-Based Plaster |
| ASTM C 1325 : 2008 | Standard Specification for Non-Asbestos Fiber-Mat Reinforced Cementitious Backer Units |
| ASTM C 1063 : 2007 | Standard Specification for Installation of Lathing and Furring to Receive Interior and Exterior Portland Cement-Based Plaster |
| ASTM C 1325 : 2017 : REV A | Standard Specification for Non-Asbestos Fiber-Mat Reinforced Cementitious Backer Units |
| ASTM E 1825 : 2021 | Standard Guide for Evaluation of Building Exterior Enclosure Materials, Products, and Systems |
| ASTM C 1186 : 2002 | Standard Specification for Flat Non-Asbestos Fiber-Cement Sheets |
| ASTM C 1325 : 2017-02 | SPECIFICATION FOR NON-ASBESTOS FIBER-MAT REINFORCED CEMENTITIOUS BACKER UNITS |
| ASTM C 1325 : 2022 | Standard Specification for Fiber-Mat Reinforced Cementitious Backer Units |
| ASTM C 1325 : 2008 : REV A | Standard Specification for Non-Asbestos Fiber-Mat Reinforced Cementitious Backer Units |
| ASTM C 1063 : 2022 : REV A | Standard Specification for Installation of Lathing and Furring to Receive Interior and Exterior Portland Cement-Based Plaster |
| ASTM C 1063 : 2017 : REV A | Standard Specification for Installation of Lathing and Furring to Receive Interior and Exterior Portland Cement-Based Plaster |
| ASTM C 1325 : 2017 | Standard Specification for Non-Asbestos Fiber-Mat Reinforced Cementitious Backer Units |
| ASTM C 1325 : 2021 | Standard Specification for Fiber-Mat Reinforced Cementitious Backer Units |
| ASTM C 1063 : 2006 | Standard Specification for Installation of Lathing and Furring to Receive Interior and Exterior Portland Cement-Based Plaster |
| ASTM C 1186 : 2008 : R2012 | Standard Specification for Flat Fiber-Cement Sheets |
| ASTM C 1063 : 2017 | Standard Specification for Installation of Lathing and Furring to Receive Interior and Exterior Portland Cement-Based Plaster |
| ASTM C 1186 : 1999 : EDT 1 | Standard Specification for Flat Non-Asbestos Fiber-Cement Sheets |
| ASTM C 1063 : 2016 | Standard Specification for Installation of Lathing and Furring to Receive Interior and Exterior Portland Cement-Based Plaster |
| ASTM C 1063 : 2016 : REV A | Standard Specification for Installation of Lathing and Furring to Receive Interior and Exterior Portland Cement-Based Plaster |
| ASTM C 1186 : 2022 | Standard Specification for Flat Fiber-Cement Sheets |
| ASTM C 1063 : 1999 | Standard Specification for Installation of Lathing and Furring to Receive Interior and Exterior Portland Cement-Based Plaster |
| ASTM C 1063 : 2012 : REV C | Standard Specification for Installation of Lathing and Furring to Receive Interior and Exterior Portland Cement-Based Plaster |
| ASTM C 1186 : 2008 : R2016 | Standard Specification for Flat Fiber-Cement Sheets |
| ASTM E 1825 : 2006 | Standard Guide for Evaluation of Exterior Building Wall Materials, Products, and Systems |
| ASTM C 1063 : 2008 | Standard Specification for Installation of Lathing and Furring to Receive Interior and Exterior Portland Cement-Based Plaster |
| ASTM C 1063 : 2022 | Standard Specification for Installation of Lathing and Furring to Receive Interior and Exterior Portland Cement-Based Plaster |
| ASTM C 1186 : 2007 | Standard Specification for Flat Non-Asbestos Fiber-Cement Sheets |
| ASTM C 1186 : 2008 | Standard Specification for Flat Fiber-Cement Sheets |
| ASTM C 1063 : 2014 : REV D | Standard Specification for Installation of Lathing and Furring to Receive Interior and Exterior Portland Cement-Based Plaster |
| ASTM C 1063 : 2017 : REV B | Standard Specification for Installation of Lathing and Furring to Receive Interior and Exterior Portland Cement-Based Plaster |
| ASTM C 1063 : 2016 : REV B | Standard Specification for Installation of Lathing and Furring to Receive Interior and Exterior Portland Cement-Based Plaster |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.