ASTM C 168 : 2017-06
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
TERMINOLOGY RELATING TO THERMAL INSULATION
Superseded date
29-04-2018
Published date
01-06-2017
CONTAINED IN VOL. 04.06, 2018 Gives definitions, symbols, units, and abbreviations of terms used in ASTM standards pertaining to thermal insulating materials, and to materials associated with them.
| Committee |
C 16
|
| DocumentType |
Standard
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| ASTM E 398 : 2013 : REDLINE | Standard Test Method for Water Vapor Transmission Rate of Sheet Materials Using Dynamic Relative Humidity Measurement |
| ASTM C 800 : 2014 : REDLINE | Standard Specification for Fibrous Glass Blanket Insulation (Aircraft Type) |
| ASTM E 1423 : 2014 : REDLINE | Standard Practice for Determining Steady State Thermal Transmittance of Fenestration Systems |
| ASTM C 303 : 2010 | Standard Test Method for Dimensions and Density of Preformed Block and Board-Type Thermal Insulation |
| ASTM C 1335:2012 | Standard Test Method for Measuring Non-Fibrous Content of Man-Made Rock and Slag Mineral Fiber Insulation |
| ASTM C 991 : 2016 : REDLINE | Standard Specification for Flexible Fibrous Glass Insulation for Metal Buildings |
| ASTM C 1371 : 2015 : REDLINE | Standard Test Method for Determination of Emittance of Materials Near Room Temperature Using Portable Emissometers |
| ASTM C 1667 : 2015 : REDLINE | Standard Test Method for Using Heat Flow Meter Apparatus to Measure the Center-of-Panel Thermal Transmission Properties of Vacuum Insulation Panels |
| ASTM C 1158 : 2005 | Standard Practice for Installation and Use of Radiant Barrier Systems (RBS) in Building Construction |
| ASTM C 1114 : 2006 | Standard Test Method for Steady-State Thermal Transmission Properties by Means of the Thin-Heater Apparatus |
| ASTM C 1763 : 2016 : REDLINE | Standard Test Method for Water Absorption by Immersion of Thermal Insulation Materials |
| ASTM C 1393 : 2014-02 | SPECIFICATION FOR PERPENDICULARLY ORIENTED MINERAL FIBER ROLL AND SHEET THERMAL INSULATION FOR PIPES AND TANKS |
| ASTM C 1130 : 2017 : REDLINE | Standard Practice for Calibration of Thin Heat Flux Transducers |
| ASTM C 1340/C1340M : 2010 | Standard Practice for Estimation of Heat Gain or Loss Through Ceilings Under Attics Containing Radiant Barriers by Use of a Computer Program |
| ASTM C 1290 : 2016 : REDLINE | Standard Specification for Flexible Fibrous Glass Blanket Insulation Used to Externally Insulate HVAC Ducts |
| ASTM C 1320 : 2010 | Standard Practice for Installation of Mineral Fiber Batt and Blanket Thermal Insulation for Light Frame Construction |
| ASTM E 2266 : 2011 : REDLINE | Standard Guide for Design and Construction of Low-Rise Frame Building Wall Systems to Resist Water Intrusion |
| DIN 4140:2014-04 | Insulation work on industrial installations and building equipment - Execution of thermal and cold insulations |
| ASTM E 2032 : 2009 : R2013 | Standard Guide for Extension of Data From Fire Resistance Tests Conducted in Accordance with ASTM E 119 |
| ASTM E 2032 : 2009 | Standard Guide for Extension of Data From Fire Resistance Tests Conducted in Accordance with ASTM E 119 |
| ASTM C 1046 : 1995 : R2007 | Standard Practice for In-Situ Measurement of Heat Flux and Temperature on Building Envelope Components |
| ASTM E 2231 : 2018 : REDLINE | Standard Practice for Specimen Preparation and Mounting of Pipe and Duct Insulation Materials to Assess Surface Burning Characteristics |
| ASTM C 1258 : 2008 : R2013 | Standard Test Method for Elevated Temperature and Humidity Resistance of Vapor Retarders for Insulation |
| ASTM C 1258 : 2008 | Standard Test Method for Elevated Temperature and Humidity Resistance of Vapor Retarders for Insulation |
| ASTM C 302 : 2013 : R2017 | Standard Test Method for Density and Dimensions of Preformed Pipe-Covering-Type Thermal Insulation |
| ASTM C 209 : 2015 : REDLINE | Standard Test Methods for Cellulosic Fiber Insulating Board |
| ASTM C 665 : 2017 : REDLINE | Standard Specification for Mineral-Fiber Blanket Thermal Insulation for Light Frame Construction and Manufactured Housing |
| ASTM C 1003 : 1983 : R1992 : EDT 1 | Test Method for Thermal Performance of Cooling-Air Duct Sections, Using a Calibrated Hot Box (Withdrawn 1997) |
| ASTM C 1061 : 1986 | Test Method for Thermal Transmission Properties of Non-Homogeneous Insulation Panels Installed Vertically (Withdrawn 1995) |
| ASTM C 302 : 2013 | Standard Test Method for Density and Dimensions of Preformed Pipe-Covering-Type Thermal Insulation |
| ASTM C 303 : 2010 : R2016 : EDT 1 | Standard Test Method for Dimensions and Density of Preformed Block and Board–Type Thermal Insulation |
| ASTM E 1993 : 1998 | Standard Specification for Bituminous Water Vapor Retarders Used in Contact with Soil or Granular Fill Under Concrete Slabs |
| ASTM C 1427 : 2016 : REDLINE | Standard Specification for Extruded Preformed Flexible Cellular Polyolefin Thermal Insulation in Sheet and Tubular Form |
| ASTM C 1729 : 2017 : REDLINE | Standard Specification for Aluminum Jacketing for Insulation |
| ASTM C 1224 : 2015 : REDLINE | Standard Specification for Reflective Insulation for Building Applications |
| ASTM C 1335 : 2012 : R2017 | Standard Test Method for Measuring Non-Fibrous Content of Man-Made Rock and Slag Mineral Fiber Insulation |
| ASTM E 96/E96M : 2016 : REDLINE | Standard Test Methods for Water Vapor Transmission of Materials |
| ASTM C 1859:2017 | Standard Practice for Determination of Thermal Resistance of Loose-Fill Building Insulation in Side Wall Applications |
| ASTM E 631 : 2015 : REDLINE | Standard Terminology of Building Constructions |
| ASTM F 683 : 2014 : REDLINE | Standard Practice for Selection and Application of Thermal Insulation for Piping and Machinery |
| ASTM C 1046 : 1995 : R2001 | Standard Practice for In-Situ Measurement of Heat Flux and Temperature on Building Envelope Components |
| ASTM C 1046 : 1995 | Standard Practice for In-Situ Measurement of Heat Flux and Temperature on Building Envelope Components |
| ASTM C 1155 : 1995 : R2001 | Standard Practice for Determining Thermal Resistance of Building Envelope Components from the In-Situ Data |
| ASTM C 950/C950M : 2008 : R2012 | Standard Practice for Repair of a Rigid Cellular Polyurethane Insulation System on Outdoor Service Vessels |
| ASTM C 1373/C1373M : 2011 | Standard Practice for Determination of Thermal Resistance of Attic Insulation Systems Under Simulated Winter Conditions |
| ASTM C 835 : 2006 : R2013 : EDT 1 | Standard Test Method for Total Hemispherical Emittance of Surfaces up to 1400°C |
| ASTM C 163 : 2005 : R2016 | Standard Practice for Mixing Thermal Insulating Cement Samples |
| ASTM C 945 : 2005 : R2012 | Standard Practice for Design Considerations and Spray Application of a Rigid Cellular Polyurethane Insulation System on Outdoor Service Vessels |
| ASTM C 533 : 2017 : REDLINE | Standard Specification for Calcium Silicate Block and Pipe Thermal Insulation |
| ASTM C 870 : 2011 : R2017 | Standard Practice for Conditioning of Thermal Insulating Materials |
| ASTM C 163 : 2005 : R2010 | Standard Practice for Mixing Thermal Insulating Cement Samples |
| ASTM C 196 : 2000 | Standard Specification for Expanded or Exfoliated Vermiculite Thermal Insulating Cement |
| ASTM C 549 : 2006 : R2012 | Standard Specification for Perlite Loose Fill Insulation |
| ASTM C 755 : 2010 : EDT 1 | Standard Practice for Selection of Water Vapor Retarders for Thermal Insulation |
| ASTM C 1146 : 2009 : R2018 | Standard Guide for Prefabricated Panel and H-bar Insulation Systems for Vessels, Ducts and Equipment Operating at Temperatures Above Ambient Air |
| ASTM C 1146 : 2009 | Standard Guide for Prefabricated Panel and H<span class='unicode'>–</span>bar Insulation Systems for Vessels, Ducts and Equipment Operating at Temperatures Above Ambient Air |
| ASTM C 1373/C1373M : 2011 : R2017 | Standard Practice for Determination of Thermal Resistance of Attic Insulation Systems Under Simulated Winter Conditions |
| ASTM C 755 : 2010 | Standard Practice for Selection of Water Vapor Retarders for Thermal Insulation |
| ASTM C 196 : 2000 : R2010 | Standard Specification for Expanded or Exfoliated Vermiculite Thermal Insulating Cement |
| ASTM C 870 : 2011 | Standard Practice for Conditioning of Thermal Insulating Materials |
| ASTM E 241 : 2009 : R2014 : EDT 1 | Standard Guide for Limiting Water-Induced Damage to Buildings |
| ASTM C 1676/C1676M : 2014 : REDLINE | Standard Specification for Microporous Thermal Insulation |
| ASTM C 1497 : 2016 : REDLINE | Standard Specification for Cellulosic Fiber Stabilized Thermal Insulation |
| ASTM C 1149 : 2017 : REDLINE | Standard Specification for Self-Supported Spray Applied Cellulosic Thermal Insulation |
| ASTM C 335 : 2005 | Standard Test Method for Steady-State Heat Transfer Properties of Pipe Insulation |
| ASTM C 950/C950M : 2008 : R2017 | Standard Practice for Repair of a Rigid Cellular Polyurethane Insulation System on Outdoor Service Vessels |
| ASTM C 1574 : 2004 | Standard Guide for Determining Blown Density of Pneumatically Applied Loose-Fill Mineral Fiber Thermal Insulation |
| ASTM C 196 : 2000 : R2005 | Standard Specification for Expanded or Exfoliated Vermiculite Thermal Insulating Cement |
| ASTM C 610 : 2017 : REDLINE | Standard Specification for Molded Expanded Perlite Block and Pipe Thermal Insulation |
| ASTM C 647 : 2008 : R2013 | Standard Guide to Properties and Tests of Mastics and Coating Finishes for Thermal Insulation |
| ASTM E 1730 : 2015 : REDLINE | SPECIFICATION FOR RIGID FOAM FOR USE IN STRUCTURAL SANDWICH PANEL CORES |
| ASTM C 1321 : 2015 : REDLINE | Standard Practice for Installation and Use of Interior Radiation Control Coating Systems (IRCCS) in Building Construction |
| ASTM C 1794 : 2015 | Standard Test Methods for Determination of the Water Absorption Coefficient by Partial Immersion |
| ASTM C 1410 : 2017 : REDLINE | Standard Specification for Cellular Melamine Thermal and Sound-Absorbing Insulation |
| ASTM C 1015 : 2017 : REDLINE | Standard Practice for Installation of Cellulosic and Mineral Fiber Loose-Fill Thermal Insulation |
| ASTM C 1086 : 2009 | Standard Specification for Glass Fiber Mechanically Bonded Felt Thermal Insulation |
| ASTM C 1744 : 2012 : REDLINE | Standard Practice for Installation and Use of Radiant Barrier Systems (RBS) in Commercial/Industrial Building Construction |
| ASTM C 1146 : 2009 : R2013 | Standard Guide for Prefabricated Panel and H–bar Insulation Systems for Vessels, Ducts and Equipment Operating at Temperatures Above Ambient Air |
| ASTM C 1340 : 2004 | Standard Practice for Estimation of Heat Gain or Loss Through Ceilings Under Attics Containing Radiant Barriers by Use of a Computer Program |
| ASTM C 1620 : 2016-03 | SPECIFICATION FOR AEROSOL POLYURETHANE AND AEROSOL LATEX FOAM SEALANTS |
| ASTM C 1512 : 2010 | Standard Test Method for Characterizing the Effect of Exposure to Environmental Cycling on Thermal Performance of Insulation Products |
| ASTM C 1060 : 2011 : REV A : R2015 | Standard Practice for Thermographic Inspection of Insulation Installations in Envelope Cavities of Frame Buildings |
| ASTM E 2599 : 2018 : REDLINE | Standard Practice for Specimen Preparation and Mounting of Reflective Insulation, Radiant Barrier and Vinyl Stretch Ceiling Materials for Building Applications to Assess Surface Burning Characteristics |
| ASTM C 835 : 2006 | Standard Test Method for Total Hemispherical Emittance of Surfaces up to 1400°C |
| ASTM C 929 : 2014 : REDLINE | Standard Practice for Handling, Transporting, Shipping, Storage, Receiving, and Application of Thermal Insulation Materials For Use in Contact with Austenitic Stainless Steel |
| ASTM C 1014 : 2017 : REDLINE | Standard Specification for Spray-Applied Mineral Fiber Thermal and Sound Absorbing Insulation |
| ASTM C 461 : 2017 : REDLINE | Standard Test Methods for Mastics and Coatings Used With Thermal Insulation |
| ASTM C 166 : 2005 : R2016 | Standard Test Method for Covering Capacity and Volume Change Upon Drying of Thermal Insulating Cement |
| ASTM C 680 : 2014 : REDLINE | Standard Practice for Estimate of the Heat Gain or Loss and the Surface Temperatures of Insulated Flat, Cylindrical, and Spherical Systems by Use of Computer Programs |
| ASTM C 419 : 2008 : R2013 | Standard Practice for Making and Curing Test Specimens of Mastic Thermal Insulation Coatings |
| ASTM C 1101/C1101M : 2006 | Standard Test Methods for Classifying the Flexibility or Rigidity of Mineral Fiber Blanket and Board Insulation |
| ASTM C 1044 : 2016 : REDLINE | Standard Practice for Using a Guarded-Hot-Plate Apparatus or Thin-Heater Apparatus in the Single-Sided Mode |
| ASTM C 196 : 2000 : R2016 | Standard Specification for Expanded or Exfoliated Vermiculite Thermal Insulating Cement |
| ASTM C 195 : 2007 : R2013 | Standard Specification for Mineral Fiber Thermal Insulating Cement |
| ASTM C 945 : 2005 : R2017 | Standard Practice for Design Considerations and Spray Application of a Rigid Cellular Polyurethane Insulation System on Outdoor Service Vessels |
| ASTM C 871 : 2018 : REDLINE | Standard Test Methods for Chemical Analysis of Thermal Insulation Materials for Leachable Chloride, Fluoride, Silicate, and Sodium Ions |
| ASTM C 421 : 2008 : R2014 | Standard Test Method for Tumbling Friability of Preformed Block-Type and Preformed Pipe-Covering-Type Thermal Insulation |
| ASTM C 553 : 2013 : REDLINE | Standard Specification for Mineral Fiber Blanket Thermal Insulation for Commercial and Industrial Applications |
| ASTM C 1483 : 2004 | Standard Specification for Exterior Solar Radiation Control Coatings on Buildings |
| ASTM C 335/C335M : 2017 : REDLINE | Standard Test Method for Steady-State Heat Transfer Properties of Pipe Insulation |
| ASTM C 335 : 2005 : REV A | Standard Test Method for Steady-State Heat Transfer Properties of Pipe Insulation |
| ASTM C 1574 : 2004 : R2008 : EDT 1 | Standard Guide for Determining Blown Density of Pneumatically Applied Loose-Fill Mineral Fiber Thermal Insulation |
| ASTM C 950/C950M : 2008 | Standard Practice for Repair of a Rigid Cellular Polyurethane Insulation System on Outdoor Service Vessels |
| ASTM C 1060 : 2011 : REV A | Standard Practice for Thermographic Inspection of Insulation Installations in Envelope Cavities of Frame Buildings |
| ASTM C 1574 : 2004 : R2013 | Standard Guide for Determining Blown Density of Pneumatically Applied Loose-Fill Mineral Fiber Thermal Insulation |
| ASTM C 1373 : 2003 | Standard Practice for Determination of Thermal Resistance of Attic Insulation Systems Under Simulated Winter Conditions |
| ASTM C 1086 : 2009 : R2016 | Standard Specification for Glass Fiber Mechanically Bonded Felt Thermal Insulation |
| ASTM C 165 : 2007 : R2017 | Standard Test Method for Measuring Compressive Properties of Thermal Insulations |
| ASTM C 1512 : 2010 : R2015 : EDT 1 | Standard Test Method for Characterizing the Effect of Exposure to Environmental Cycling on Thermal Performance of Insulation Products |
| ASTM C 1784 : 2014 : REDLINE | Standard Test Method for Using a Heat Flow Meter Apparatus for Measuring Thermal Storage Properties of Phase Change Materials and Products |
| ASTM C 1767M : 2016-03 | SPECIFICATION FOR STAINLESS STEEL JACKETING FOR INSULATION |
| ASTM C 516 : 2008 | Standard Specification for Vermiculite Loose Fill Thermal Insulation |
| ASTM C 165 : 2007 | Standard Test Method for Measuring Compressive Properties of Thermal Insulations |
| ASTM C 1574 : 2004 : R2008 | Standard Guide for Determining Blown Density of Pneumatically Applied Loose-Fill Mineral Fiber Thermal Insulation |
| ASTM C 1313/C1313M : 2013 : REDLINE | Standard Specification for Sheet Radiant Barriers for Building Construction Applications |
| ASTM C 1616 : 2007 | Standard Test Method for Determining the Moisture Content of Organic and Inorganic Insulation Materials by Weight |
| ASTM C 656 : 2017 : REDLINE | Standard Specification for Structural Insulating Board, Calcium Silicate |
| ASTM C 755 : 2010 : R2015 : EDT 1 | Standard Practice for Selection of Water Vapor Retarders for Thermal Insulation |
| ASTM C 1153 : 2010 : R2015 | Standard Practice for Location of Wet Insulation in Roofing Systems Using Infrared Imaging |
| ASTM E 241 : 2009 | Standard Guide for Limiting Water-Induced Damage to Buildings |
| ASTM C 1304 : 2008 : R2013 | Standard Test Method for Assessing the Odor Emission of Thermal Insulation Materials |
| ASTM C 795 : 2008 : R2013 | Standard Specification for Thermal Insulation for Use in Contact with Austenitic Stainless Steel |
| ASTM C 1594 : 2011 | Standard Specification for Polyimide Rigid Cellular Thermal Insulation |
| ASTM C 335 : 2005 : REV A : EDT 1 | Standard Test Method for Steady-State Heat Transfer Properties of Pipe Insulation |
| ASTM C 390 : 2008 : EDT 1 | Standard Practice for Sampling and Acceptance of Thermal Insulation Lots |
| ASTM C 1101/C1101M : 2006 : R2017 | Standard Test Methods for Classifying the Flexibility or Rigidity of Mineral Fiber Blanket and Board Insulation |
| ASTM C 1852 : 2017 | Standard Guide for Product Selection/Delivery Systems for Aerosol Foam Sealants and Adhesives |
| ASTM D 7425 : 2008 | Standard Specification for Spray Polyurethane Foam Used for Roofing Applications |
| ASTM F 2165 : 2013-12 | SPECIFICATION FOR FLEXIBLE PRE-INSULATED PIPING |
| ASTM C 950 : 2005 | Standard Practice for Repair of a Rigid Cellular Polyurethane Insulation System on Outdoor Service Vessels |
| ASTM C 1058/C1058M : 2010 : R2015 | Standard Practice for Selecting Temperatures for Evaluating and Reporting Thermal Properties of Thermal Insulation |
| ASTM C 195 : 2007 | Standard Specification for Mineral Fiber Thermal Insulating Cement |
| ASTM C 1848 : 2017 | Standard Practice for Installation of High-Pressure Spray Polyurethane Foam Insulation for the Building Enclosure |
| ASTM C 653 : 2017 : REDLINE | Standard Guide for Determination of the Thermal Resistance of Low-Density Blanket-Type Mineral Fiber Insulation |
| ASTM C 419 : 2008 | Standard Practice for Making and Curing Test Specimens of Mastic Thermal Insulation Coatings |
| ASTM C 449 : 2007 : R2019 | Standard Specification for Mineral Fiber Hydraulic-Setting Thermal Insulating and Finishing Cement |
| ASTM C 1153 : 2010 | Standard Practice for Location of Wet Insulation in Roofing Systems Using Infrared Imaging |
| ASTM C 1060 : 2011 | Standard Practice for Thermographic Inspection of Insulation Installations in Envelope Cavities of Frame Buildings |
| ASTM C 612 : 2014 : REDLINE | Standard Specification for Mineral Fiber Block and Board Thermal Insulation |
| ASTM C 166 : 2005 : R2010 | Standard Test Method for Covering Capacity and Volume Change Upon Drying of Thermal Insulating Cement |
| ASTM C 1630 : 2011 : R2016 | Standard Guide for Development of Coverage Charts for Loose-Fill Thermal Building Insulations |
| ASTM C 1574 : 2004 : R2018 | Standard Guide for Determining Blown Density of Pneumatically Applied Loose-Fill Mineral Fiber Thermal Insulation |
| ASTM C 727 : 2012 : REDLINE | Standard Practice for Installation and Use of Reflective Insulation in Building Constructions |
| ASTM E 1745 : 2017 : REDLINE | Standard Specification for Plastic Water Vapor Retarders Used in Contact with Soil or Granular Fill under Concrete Slabs |
| ASTM C 755 : 2010 : R2015 | Standard Practice for Selection of Water Vapor Retarders for Thermal Insulation |
| ASTM C 449 : 2007 : R2013 | Standard Specification for Mineral Fiber Hydraulic-Setting Thermal Insulating and Finishing Cement |
| ASTM C 764 : 2017 : REDLINE | Standard Specification for Mineral Fiber Loose-Fill Thermal Insulation |
| ASTM C 550 : 2015 : REDLINE | Standard Test Method for Measuring Trueness and Squareness of Rigid Block and Board Thermal Insulation |
| ASTM C 421 : 2008 | Standard Test Method for Tumbling Friability of Preformed Block-Type and Preformed Pipe-Covering-Type Thermal Insulation |
| ASTM C 165 : 2007 : R2012 | Standard Test Method for Measuring Compressive Properties of Thermal Insulations |
| ASTM C 449 : 2007 | Standard Specification for Mineral Fiber Hydraulic-Setting Thermal Insulating and Finishing Cement |
| ASTM C 390 : 2008 : R2013 | Standard Practice for Sampling and Acceptance of Thermal Insulation Lots |
| ASTM C 916 : 2014 : REDLINE | Standard Specification for Adhesives for Duct Thermal Insulation |
| ASTM C 1774 : 2013 | Standard Guide for Thermal Performance Testing of Cryogenic Insulation Systems |
| ASTM C 166 : 2005 | Standard Test Method for Covering Capacity and Volume Change Upon Drying of Thermal Insulating Cement |
| ASTM C 1785 : 2017 : REDLINE | Standard Test Method for Concentration of Pinhole Detections in Moisture Barriers on Metal Jacketing |
| ASTM C 1304 : 2008 | Standard Test Method for Assessing the Odor Emission of Thermal Insulation Materials |
| ASTM C 795 : 2008 : R2018 | Standard Specification for Thermal Insulation for Use in Contact with Austenitic Stainless Steel |
| ASTM C 795 : 2008 | Standard Specification for Thermal Insulation for Use in Contact with Austenitic Stainless Steel |
| ASTM C 516 : 2008 : R2013 : EDT 1 | Standard Specification for Vermiculite Loose Fill Thermal Insulation |
| ASTM C 1058/C1058M : 2010 | Standard Practice for Selecting Temperatures for Evaluating and Reporting Thermal Properties of Thermal Insulation |
| ASTM C 450 : 2018 : REDLINE | Standard Practice for Fabrication of Thermal Insulating Fitting Covers for NPS Piping, and Vessel Lagging |
| ASTM C 1512 : 2010 : R2015 | Standard Test Method for Characterizing the Effect of Exposure to Environmental Cycling on Thermal Performance of Insulation Products |
| ASTM C 163 : 2005 | Standard Practice for Mixing Thermal Insulating Cement Samples |
| ASTM C 488 : 2016 : REDLINE | Standard Test Method for Conducting Exterior Exposure Tests of Finishes for Thermal Insulation |
| ASTM C 1616 : 2007 : R2012 | Standard Test Method for Determining the Moisture Content of Organic and Inorganic Insulation Materials by Weight |
| ASTM C 1594 : 2011 : R2017 | Standard Specification for Polyimide Rigid Cellular Thermal Insulation |
| ASTM C 1676 : 2008 | Standard Specification for Microporous Thermal Insulation |
| ASTM E 1993/E1993M : 1998 : R2013 : EDT 1 | Standard Specification for Bituminous Water Vapor Retarders Used in Contact with Soil or Granular Fill Under Concrete Slabs |
| ASTM C 449/C449M : 2000 | Standard Specification for Mineral Fiber Hydraulic-Setting Thermal Insulating and Finishing Cement |
| ASTM C 549 : 2006 | Standard Specification for Perlite Loose Fill Insulation |
| ASTM C 520 : 2015 : REDLINE | Standard Test Methods for Density of Granular Loose Fill Insulations |
| ASTM C 1101/C1101M : 2006 : R2012 | Standard Test Methods for Classifying the Flexibility or Rigidity of Mineral Fiber Blanket and Board Insulation |
| ASTM C 390 : 2008 | Standard Practice for Sampling and Acceptance of Thermal Insulation Lots |
| ASTM E 3054/E3054M : 2016 | Standard Guide for Characterization and Use of Hygrothermal Models for Moisture Control Design in Building Envelopes |
| ASTM C 1616 : 2007 : EDT 1 | Standard Test Method for Determining the Moisture Content of Organic and Inorganic Insulation Materials by Weight |
| ASTM C 945 : 2005 | Standard Practice for Design Considerations and Spray Application of a Rigid Cellular Polyurethane Insulation System on Outdoor Service Vessels |
| ASTM C 647 : 2008 | Standard Guide to Properties and Tests of Mastics and Coating Finishes for Thermal Insulation |
| ASTM C 1129 : 2017 : REDLINE | Standard Practice for Estimation of Heat Savings by Adding Thermal Insulation to Bare Valves and Flanges |
| ASTM C 1630 : 2011 | Standard Guide for Development of Coverage Charts for Loose-Fill Thermal Building Insulations |
| ASTM C 1313 : 2005 | Standard Specification for Sheet Radiant Barriers for Building Construction Applications |
| ASTM E 2988 : 2017 : REDLINE | Standard Practice for Specimen Preparation and Mounting of Flexible Fibrous Glass Insulation for Metal Buildings to Assess Surface Burning Characteristics |
| ASTM C 1482 : 2017 : REDLINE | Standard Specification for Polyimide Flexible Cellular Thermal and Sound Absorbing Insulation |
| ASTM E 154/E154M : 2008 : REV A : R2013 : EDT 1 | Standard Test Methods for Water Vapor Retarders Used in Contact with Earth Under Concrete Slabs, on Walls, or as Ground Cover |
| ASTM C 1263 : 1995 : R2010 | Standard Test Method for Thermal Integrity of Flexible Water Vapor Retarders |
| ASTM C 739 : 2017 : REDLINE | Standard Specification for Cellulosic Fiber Loose-Fill Thermal Insulation |
| ASTM C 1696 : 2016 : REDLINE | Standard Guide for Industrial Thermal Insulation Systems |
| ASTM C 1363 : 2011 : REDLINE | Standard Test Method for Thermal Performance of Building Materials and Envelope Assemblies by Means of a Hot Box Apparatus |
| ASTM C 1029 : 2015 : REDLINE | Standard Specification for Spray-Applied Rigid Cellular Polyurethane Thermal Insulation |
| ASTM C 1045 : 2007 : R2013 | Standard Practice for Calculating Thermal Transmission Properties Under Steady-State Conditions |
| ASTM C 1132 : 1995 | Standard Practice for Calibration of the Heat Flow Meter Apparatus (Withdrawn 2002) |
| ASTM C 383 : 1997 | Standard Test Method for Wet Adhesion of Thermal Insulating Cements to Metal (Withdrawn 2002) |
| ASTM C 354 : 1997 | Standard Test Method for Compressive Strength of Thermal Insulating or Finishing Cement (Withdrawn 2002) |
| ASTM C 667 : 2017 : REDLINE | Standard Specification for Prefabricated Reflective Insulation Systems for Equipment and Pipe Operating at Temperatures above Ambient Air |
| ASTM C 1033 : 1985 : R2000 | Standard Test Method for Steady-State Heat Transfer Properties of Pipe Insulation Installed Vertically (Withdrawn 2003) |
| ASHRAE HDBK REFRIGERATION : 2014 | ASHRAE HANDBOOK - REFRIGERATION |
| ASTM D 7425/D7425M : 2013 : REDLINE | Standard Specification for Spray Polyurethane Foam Used for Roofing Applications |
| ASTM C 447 : 2015 : REDLINE | Standard Practice for Estimating the Maximum Use Temperature of Thermal Insulations |
| ASTM C 356 : 2017 : REDLINE | Standard Test Method for Linear Shrinkage of Preformed High-Temperature Thermal Insulation Subjected to Soaking Heat |
| ASTM C 585 : 2010 : R2016 | Standard Practice for Inner and Outer Diameters of Thermal Insulation for Nominal Sizes of Pipe and Tubing |
| ASTM C 547 : 2017 : REDLINE | Standard Specification for Mineral Fiber Pipe Insulation |
| ASTM C 1013 : 1994 | Specification for Faced Rigid Cellular Polyisocyanurate Roof Insulation (Withdrawn 1997) |
| ASTM C 353 : 1997 | Standard Test Method for Adhesion of Dried Thermal Insulating or Finishing Cement (Withdrawn 2002) |
| ASTM E 2094 : 2002 | Standard Practice for Evaluating the Service Life of Chromogenic Glazings (Withdrawn 2011) |
| ASTM C 203 : 2005 : REV A : R2017 | Standard Test Methods for Breaking Load and Flexural Properties of Block-Type Thermal Insulation |
| ASTM C 585 : 2010 | Standard Practice for Inner and Outer Diameters of Thermal Insulation for Nominal Sizes of Pipe and Tubing |
| ASTM C 1809 : 2016 : REDLINE | Standard Practice for Preparation of Specimens and Reporting of Results for Permeance Testing of Pressure Sensitive Adhesive Sealed Joints in Insulation Vapor Retarders |
| ASTM C 203 : 2005 | Standard Test Methods for Breaking Load and Flexural Properties of Block-Type Thermal Insulation |
| ASTM C 203 : 2005 : REV A : R2012 | Standard Test Methods for Breaking Load and Flexural Properties of Block-Type Thermal Insulation |
| ASTM C 203 : 2005 : REV A | Standard Test Methods for Breaking Load and Flexural Properties of Block-Type Thermal Insulation |
| ASTM C 1483/C1483M : 2017 : REDLINE | Standard Specification for Exterior Solar Radiation Control Coatings on Buildings |
| ASTM C 1057 : 2017 : REDLINE | Standard Practice for Determination of Skin Contact Temperature from Heated Surfaces Using a Mathematical Model and Thermesthesiometer |
| ASTM C 1033 : 1985 : R1994 : EDT 1 | Standard Test Method for Steady-State Heat Transfer Properties of Pipe Insulation Installed Vertically |
| ASTM C 971 : 1982 : R1992 | Standard Guide for Selection and Application of Insulation Systems for Heating, Ventilating, and Air Conditioning Duct Work |
| ASTM C 1710 : 2016 : REDLINE | Standard Guide for Installation of Flexible Closed Cell Preformed Insulation in Tube and Sheet Form |
| ASTM C 1263 : 1995 : R2005 | Standard Test Method for Thermal Integrity of Flexible Water Vapor Retarders |
| ASTM C 1263 : 1995 : R2015 | Standard Test Method for Thermal Integrity of Flexible Water Vapor Retarders |
| ASTM C 1423 : 2016 : REDLINE | Standard Guide for Selecting Jacketing Materials for Thermal Insulation |
| ASTM C 976 : 1990 : R1996 : EDT 1 | Standard Test Method for Thermal Performance of Building Assemblies by Means of a Calibrated Hot Box (Withdrawn 2002) |
| ASTM E 1993 : 1998 : R2008 | Standard Specification for Bituminous Water Vapor Retarders Used in Contact with Soil or Granular Fill Under Concrete Slabs |
| ASTM E 1993 : 1998 : R2002 | Standard Specification for Bituminous Water Vapor Retarders Used in Contact with Soil or Granular Fill Under Concrete Slabs |
| ASTM C 1050 : 1991 | Standard Specification for Rigid Cellular Polystyrene-Cellulosic Fiber Composite Roof Insulation (Withdrawn 1999) |
| ASTM C 1340/C1340M : 2010 : R2015 | Standard Practice for Estimation of Heat Gain or Loss Through Ceilings Under Attics Containing Radiant Barriers by Use of a Computer Program |
| ASTM C 1134 : 2017 : REDLINE | Standard Test Method for Water Retention of Rigid Thermal Insulations Following Partial Immersion |
| ASTM C 592 : 2016 : REDLINE | Standard Specification for Mineral Fiber Blanket Insulation and Blanket-Type Pipe Insulation (Metal-Mesh Covered) (Industrial Type) |
| ASTM C 1775 : 2014 : REDLINE | Standard Specification for Laminate Protective Jacket and Tape for Use over Thermal Insulation for Outdoor Applications |
| ASTM C 208 : 2012 | Standard Specification for Cellulosic Fiber Insulating Board |
| ASTM C 208 : 2012 : R2017 : EDT 1 | Standard Specification for Cellulosic Fiber Insulating Board |
| ASTM C 1263 : 1995 : R2000 | Standard Test Method for Thermal Integrity of Flexible Water Vapor Retarders |
| ASTM C 1685 : 2015 : REDLINE | Standard Specification for Pneumatically Applied High-Temperature Fiber Thermal Insulation for Industrial Applications |
| ASTM C 1263 : 1995. | Standard Test Method for Thermal Integrity of Flexible Water Vapor Retarders |
| ASTM C 1263 : 1995 : R2005 : EDT 1 | Standard Test Method for Thermal Integrity of Flexible Water Vapor Retarders |
| ASTM C 1822 : 2015 | Standard Specification for Insulating Covers on Accessible Lavatory Piping |
| ASTM C 1728 : 2017 : REDLINE | Standard Specification for Flexible Aerogel Insulation |
| ASTM C 303 : 2010 : R2016 | Standard Test Method for Dimensions and Density of Preformed Block and Board–Type Thermal Insulation |
| ASTM E 1993 : 1998 : R2002 : EDT 1 | Standard Specification for Bituminous Water Vapor Retarders Used in Contact with Soil or Granular Fill Under Concrete Slabs |
| ASTM C 1729M : 2017 : REDLINE | Standard Specification for Aluminum Jacketing for Insulation |
| ASTM C 1549 : 2016 : REDLINE | Standard Test Method for Determination of Solar Reflectance Near Ambient Temperature Using a Portable Solar Reflectometer |
| ASTM C 726 : 2017 : REDLINE | Standard Specification for Mineral Wool Roof Insulation Board |
| ASTM C 1045 : 2007 | Standard Practice for Calculating Thermal Transmission Properties Under Steady-State Conditions |
| ASTM C 740/C740M : 2013 : REDLINE | Standard Guide for Evacuated Reflective Insulation In Cryogenic Service |
| ASTM C 921 : 2010 | Standard Practice for Determining the Properties of Jacketing Materials for Thermal Insulation |
| ASTM C 921 : 2010 : R2015 | Standard Practice for Determining the Properties of Jacketing Materials for Thermal Insulation (Withdrawn 2021) |
| ASTM C 518 : 2017 : REDLINE | Standard Test Method for Steady-State Thermal Transmission Properties by Means of the Heat Flow Meter Apparatus |
| ASTM C 1559 : 2015 : REDLINE | Standard Test Method for Determining Wicking of Fibrous Glass Blanket Insulation (Aircraft Type) |
| ASTM C 1511 : 2015 : REDLINE | Standard Test Method for Determining the Water Retention (Repellency) Characteristics of Fibrous Glass Insulation (Aircraft Type) |
| ASTM C 1199 : 2014 : REDLINE | Standard Test Method for Measuring the Steady-State Thermal Transmittance of Fenestration Systems Using Hot Box Methods |
| ASTM C 1155 : 1995 | Standard Practice for Determining Thermal Resistance of Building Envelope Components from the In-Situ Data |
| ASTM E 2032 : 2009 : R2017 | Standard Guide for Extension of Data From Fire Resistance Tests Conducted in Accordance with ASTM E 119 |
| ASTM C 1046 : 1995 : R2013 | Standard Practice for In-Situ Measurement of Heat Flux and Temperature on Building Envelope Components |
| ASTM C 1155 : 1995 : R2013 | Standard Practice for Determining Thermal Resistance of Building Envelope Components from the In-Situ Data |
| ASTM C 1155 : 1995 : R2007 | Standard Practice for Determining Thermal Resistance of Building Envelope Components from the In-Situ Data |
| ASTM E 2750 : 2017 : REDLINE | Standard Guide for Extension of Data from Penetration Firestop System Tests Conducted in Accordance with ASTM E814 |
| ASTM E 2141 : 2014 : REDLINE | Standard Test Method for Accelerated Aging of Electrochromic Devices in Sealed Insulating Glass Units |
| ASTM C 1320 : 2010 : R2016 | Standard Practice for Installation of Mineral Fiber Batt and Blanket Thermal Insulation for Light Frame Construction |
| ASTM D 3941 : 2014 : REDLINE | Standard Test Method for Flash Point by the Equilibrium Method With a Closed-Cup Apparatus |
| ISO 7345:1987 | Thermal insulation Physical quantities and definitions |
Sorry this product is not available in your region.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.