We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
  • ASTM C 449/C449M : 2000

    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    Add to Watchlist
    This Standard has been added successfully to your Watchlist.
    Please visit My Watchlist to see all standards that you are watching.
    Please log in or to add this standard to your Watchlist.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    You need to be logged in to add this standard to your Watchlist.
    Please log in now or create an account to add.
    You already added this Product in the Watchlist.

    Standard Specification for Mineral Fiber Hydraulic-Setting Thermal Insulating and Finishing Cement

    Available format(s): 

    Superseded date:  11-11-2014

    Language(s): 

    Published date:  10-10-2000

    Publisher:  American Society for Testing and Materials

    Add to Watchlist

    Sorry this product is not available in your region.

    Add To Cart

    Abstract - (Show below) - (Hide below)

    CONTAINED IN VOL. 04.06, 2005 Specifies mineral fiber insulating and finishing cement, shipped in dry-mix form, including hydraulic-setting binder, which when mixed with water and applied with the manufacturer's directions affords a smooth surface as a final finish for heated surfaces.

    Scope - (Show below) - (Hide below)

    1.1 This specification covers mineral fiber (rock or slag) insulating and finishing cement shipped in dry-mix form, including hydraulic-setting binder, which, when mixed with water and applied in accordance with the manufacturer's directions, affords a smooth surface as a final finish for heated surfaces up to 1200oF (649oC) for specific applications. The actual temperature limit shall be agreed upon between the purchaser and the manufacturer.

    Note 1--Precautionary measures should be taken with this material as with other hydraulic-setting mixtures. This material should be used within the time period recommended by the manufacturer.

    1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.

    1.3 The following safety hazards caveat pertains only to the test method (Section 10) described in this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

    1.4 When the installation or use of thermal insulation materials, accessories, and systems may pose safety or health problems, the manufacturer shall provide the user with appropriate current information regarding any known problems associated with the recommended use of the company's products and shall also recommend protective measures to be employed in their safe utilization. The user shall establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use.

    General Product Information - (Show below) - (Hide below)

    Committee C 16
    Document Type Standard
    Publisher American Society for Testing and Materials
    Status Superseded
    Superseded By
    Supersedes

    Standards Referenced By This Book - (Show below) - (Hide below)

    ASTM F 683 : 2014 : REDLINE Standard Practice for Selection and Application of Thermal Insulation for Piping and Machinery

    Standards Referencing This Book - (Show below) - (Hide below)

    ASTM C 354 : 1997 Standard Test Method for Compressive Strength of Thermal Insulating or Finishing Cement (Withdrawn 2002)
    ASTM C 518 : 2017 : REDLINE Standard Test Method for Steady-State Thermal Transmission Properties by Means of the Heat Flow Meter Apparatus
    ASTM C 356 : 2017 : REDLINE Standard Test Method for Linear Shrinkage of Preformed High-Temperature Thermal Insulation Subjected to Soaking Heat
    ASTM C 795 : 2008 Standard Specification for Thermal Insulation for Use in Contact with Austenitic Stainless Steel
    ASTM C 168 : 2017-06 TERMINOLOGY RELATING TO THERMAL INSULATION
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective