ASTM C 778 : 2017
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
Hardcopy , PDF
06-01-2022
English
24-08-2017
This specification covers standard sand for use in the testing of hydraulic cements.
1.1This specification covers standard sand for use in the testing of hydraulic cements.
1.2The values stated in SI units are to be regarded as the standard.
1.3Values in SI units shall be obtained by measurement in SI units or by appropriate conversion, using the Rules for Conversion and Rounding given in IEEE/ASTM SI 10, of measurements made in other units.
1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
1.5This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| Committee |
C 01
|
| DocumentType |
Standard
|
| Pages |
3
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| ASTM C 10/C10M : 2019 | Standard Specification for Natural Cement |
| ASTM D 3319 : 2011 : R2017 | Standard Practice for the Accelerated Polishing of Aggregates Using the British Wheel |
| ASTM C 207 : 2018 | Standard Specification for Hydrated Lime for Masonry Purposes |
| ASTM D 7402 : 2009 : R2017 | Standard Practice for Identifying Cationic Emulsified Asphalts |
| ASTM C 932 : 2006 : R2019 | Standard Specification for Surface-Applied Bonding Compounds for Exterior Plastering |
| ASTM C 110 : 2020 | Standard Test Methods for Physical Testing of Quicklime, Hydrated Lime, and Limestone |
| ASTM C 806 : 2018 | Standard Test Method for Restrained Expansion of Expansive Cement Mortar |
| ASTM C 348 : 2021 | Standard Test Method for Flexural Strength of Hydraulic-Cement Mortars |
| ASTM C 141/C141M : 2014 | Standard Specification for Hydrated Hydraulic Lime for Structural Purposes |
| ASTM C 1707 : 2018 | Standard Specification for Pozzolanic Hydraulic Lime for Structural Purposes |
| ASTM E 518/E518M : 2021 | Standard Test Methods for Flexural Bond Strength of Masonry |
| ASTM C 1708/C1708M : 2019 | Standard Test Methods for Self-leveling Mortars Containing Hydraulic Cements |
| ASTM C 471M : 2020 : REV A : EDT 1 | Standard Test Methods for Chemical Analysis of Gypsum and Gypsum Products (Metric) |
| ASTM C 1073 : 2018 | Standard Test Method for Hydraulic Activity of Slag Cement by Reaction with Alkali |
| ASTM C 1474 : 2019 | Standard Test Method for Analysis of Isotopic Composition of Uranium in Nuclear-Grade Fuel Material by Quadrupole Inductively Coupled Plasma-Mass Spectrometry |
| ASTM C 1679 : 2017 | Standard Practice for Measuring Hydration Kinetics of Hydraulic Cementitious Mixtures Using Isothermal Calorimetry |
| ASTM C 1012/C1012M : 2018 : REV B | Standard Test Method for Length Change of Hydraulic-Cement Mortars Exposed to a Sulfate Solution |
| ASTM C 1252 : 2017 | Standard Test Methods for Uncompacted Void Content of Fine Aggregate (as Influenced by Particle Shape, Surface Texture, and Grading) |
| ASTM C 472 : 2020 | Standard Test Methods for Physical Testing of Gypsum, Gypsum Plasters, and Gypsum Concrete |
| ASTM C 1328/C1328M : 2019 : REDLINE | Standard Specification for Plastic (Stucco) Cement |
| ASTM C 1017/C1017M : 2013 : EDT 1 | Standard Specification for Chemical Admixtures for Use in Producing Flowing Concrete (Withdrawn 2022) |
| ASTM D 1734 : 1993 : R2013 | Standard Practice for Making Cementitious Panels for Testing Coatings |
| ASTM C 1329/C1329M : 2016 : REV A | Standard Specification for Mortar Cement |
| ASTM C 418 : 2020 | Standard Test Method for Abrasion Resistance of Concrete by Sandblasting |
| ASTM C 109/C109M : 2021 | Standard Test Method for Compressive Strength of Hydraulic Cement Mortars (Using 2-in. or [50mm] Cube Specimens) |
| ASTM C 1403 : 2015 | Standard Test Method for Rate of Water Absorption of Masonry Mortars |
| ASTM C 91/C91M : 2018 | Standard Specification for Masonry Cement |
| ASTM D 244 : 2009 : R2017 | Standard Test Methods and Practices for Emulsified Asphalts |
| ASTM C 311/C311M : 2018 | Standard Test Methods for Sampling and Testing Fly Ash or Natural Pozzolans for Use in Portland-Cement Concrete |
| ASTM C 928/C928M : 2020 : REV A | Standard Specification for Packaged, Dry, Rapid-Hardening Cementitious Materials for Concrete Repairs |
| ASTM C 452 : 2021 | Standard Test Method for Potential Expansion of Portland-Cement Mortars Exposed to Sulfate |
| ASTM C 305 : 2020 | Standard Practice for Mechanical Mixing of Hydraulic Cement Pastes and Mortars of Plastic Consistency |
| ASTM C 596 : 2018 | Standard Test Method for Drying Shrinkage of Mortar Containing Hydraulic Cement |
| ASTM A 1096/A1096M : 2015 | Standard Test Method for Evaluating Bond of Individual Steel Wire, Indented or Plain, for Concrete Reinforcement |
| ASTM D 4280 : 2018 | Standard Specification for Extended Life Type, Nonplowable, Raised Retroreflective Pavement Markers |
| ASTM C 156 : 2020 | Standard Test Method for Water Loss [from a Mortar Specimen] Through Liquid Membrane-Forming Curing Compounds for Concrete |
| ASTM C 1439 : 2019 | Standard Test Methods for Evaluating Latex and Powder Polymer Modifiers for use in Hydraulic Cement Concrete and Mortar |
| ASTM C 1810/C1810M : 2021 : REV A | Standard Guide for Comparing Performance of Concrete-Making Materials Using Mortar Mixtures |
| ASTM D 4383 : 2018 | Standard Specification for Plowable, Raised Retroreflective Pavement Markers |
| ASTM C 1038/C1038M : 2019 | Standard Test Method for Expansion of Hydraulic Cement Mortar Bars Stored in Water |
| ASTM C 28/C28M : 2010 : R2020 | Standard Specification for Gypsum Plasters |
| ASTM C 185 : 2020 | Standard Test Method for Air Content of Hydraulic Cement Mortar |
| ASTM C 884/C884M : 2016 | Standard Test Method for Thermal Compatibility Between Concrete and an Epoxy-Resin Overlay |
| ASTM D 7382 : 2020 | Standard Test Methods for Determination of Maximum Dry Unit Weight of Granular Soils Using a Vibrating Hammer |
| ASTM C 109/C109M : 2020 : REV B | Standard Test Method for Compressive Strength of Hydraulic Cement Mortars (Using 2-in. or [50mm] Cube Specimens) |
| ASTM C 1005 : 2019 | Standard Specification for Reference Masses and Devices for Determining Mass and Volume for Use in the Physical Testing of Hydraulic Cements |
| ASTM C 109/C109M : 2021 | Standard Test Method for Compressive Strength of Hydraulic Cement Mortars (Using 2-in. or [50mm] Cube Specimens) |
| ASTM C 1005 : 2000 | Standard Specification for Reference Masses and Devices for Determining Mass and Volume for Use in the Physical Testing of Hydraulic Cements |
| ASTM C 1005 : 2017 | Standard Specification for Reference Masses and Devices for Determining Mass and Volume for Use in the Physical Testing of Hydraulic Cements |
| ASTM C 1005 : 2010 | Standard Specification for Reference Masses and Devices for Determining Mass and Volume for Use in the Physical Testing of Hydraulic Cements |
| ASTM C 1005 : 2018 | Standard Specification for Reference Masses and Devices for Determining Mass and Volume for Use in the Physical Testing of Hydraulic Cements |
| ASTM C 136 : 1996 | Standard Test Method for Sieve Analysis of Fine and Coarse Aggregates |
| ASTM C 1005 : 2005 | Standard Specification for Reference Masses and Devices for Determining Mass and Volume for Use in the Physical Testing of Hydraulic Cements |
| ASTM C 150 : 2002 : REV A : EDT 1 | Standard Specification for Portland Cement |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.