ASTM C 957/C957M : 2017
Current
The latest, up-to-date edition.
Hardcopy , PDF
English
01-10-2017
This specification describes the required properties and test methods for high-solids content, cold liquid-applied elastomeric membrane with integral wearing surface for waterproofing building decks not subject to hydrostatic pressure.
1.1This specification describes the required properties and test methods for a cold liquid-applied elastomeric membrane for waterproofing building decks not subject to hydrostatic pressure. The specification applies only to a membrane system that has an integral wearing surface. This specification does not include specific requirements for skid resistance or fire retardance, although both may be important in specific uses.
1.2The type of membrane system described in this specification is used for pedestrian and vehicular traffic and in high-abrasion applications. The membrane may be single- or multi-component, and may consist of one or more coats (for example base coat, top coat, etc.). The coat(s) may be built to the desired thickness in one or more applications. One coat (base coat) provides the primary waterproofing function and normally comprises the major amount of organic material in the membrane. The function of the top coat(s) is to resist wear and weather. Aggregate may be used as a component of the membrane system, as all or part of a course, to increase wear and skid resistance.
1.3The committee with jurisdiction over this standard is not aware of any comparable standards published by other organizations.
1.4Test methods in this specification require a minimum 0.5-mm [0.020-in.] base coat dry film thickness. Actual thickness required for a particular application and the use of aggregate in topcoats shall be established by the membrane manufacturer.
1.5The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
1.6The following safety hazards caveat pertains only to the test method portion, Section 5, of this specification: This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.7This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Committee |
D 08
|
DocumentType |
Standard
|
Pages |
4
|
PublisherName |
American Society for Testing and Materials
|
Status |
Current
|
Supersedes |
ASTM D 1079 : 2018 : EDT 1 | Standard Terminology Relating to Roofing and Waterproofing |
ASTM D 471 : 2016 : REV A | Standard Test Method for Rubber Property—Effect of Liquids |
ASTM C 501 : 2021 | Standard Test Method for Relative Resistance to Wear of Unglazed Ceramic Tile by the Taber Abraser |
ASTM D 1079 : 2008 : REV A | Standard Terminology Relating to Roofing and Waterproofing |
ASTM D 2370 : 2016 | Standard Test Method for Tensile Properties of Organic Coatings |
ASTM D 1079 : 2016 | Standard Terminology Relating to Roofing and Waterproofing |
ASTM D 1079 : 2006 | Terminology Relating to Roofing and Waterproofing |
ASTM C 1442 : 2011 | Standard Practice for Conducting Tests on Sealants Using Artificial Weathering Apparatus |
ASTM D 2370 : 1998 | Standard Test Method for Tensile Properties of Organic Coatings |
ASTM D 609 : 2017 : R2022 | Standard Practice for Preparation of Cold-Rolled Steel Panels for Testing Paint, Varnish, Conversion Coatings, and Related Coating Products |
ASTM D 1079 : 2020 | Standard Terminology Relating to Roofing and Waterproofing |
ASTM D 1133 : 2013 : R2021 | Standard Test Method for Kauri-Butanol Value of Hydrocarbon Solvents |
ASTM C 501 : 1984 : R2015 | Standard Test Method for Relative Resistance to Wear of Unglazed Ceramic Tile by the Taber Abraser |
ASTM C 1305/C1305M : 2016 : R2023 | Standard Test Method for Crack Bridging Ability of Liquid-Applied Waterproofing Membrane |
ASTM D 412 : 2016 : EDT 1 | Standard Test Methods for Vulcanized Rubber and Thermoplastic Elastomers—Tension |
ASTM D 1079 : 2013 | Standard Terminology Relating to Roofing and Waterproofing |
ASTM D 1079 : 2007 : REV A | Terminology Relating to Roofing and Waterproofing |
ASTM D 1079 : 2010 | Standard Terminology Relating to Roofing and Waterproofing |
ASTM D 1133 : 2010 | Standard Test Method for Kauri-Butanol Value of Hydrocarbon Solvents |
ASTM D 2370 : 1998 : R2002 : EDT 1 | Standard Test Method for Tensile Properties of Organic Coatings |
ASTM D 471 : 2016 : REV A : R2021 | Standard Test Method for Rubber Property—Effect of Liquids |
ASTM C 1442 : 2014 : R2021 | Standard Practice for Conducting Tests on Sealants Using Artificial Weathering Apparatus |
ASTM D 1079 : 2018 | Standard Terminology Relating to Roofing and Waterproofing |
ASTM C 1442 : 2014 | Standard Practice for Conducting Tests on Sealants Using Artificial Weathering Apparatus |
ASTM D 412 : 2016 | Standard Test Methods for Vulcanized Rubber and Thermoplastic Elastomers—Tension |
ASTM D 1133 : 2013 | Standard Test Method for Kauri-Butanol Value of Hydrocarbon Solvents |
ASTM D 2370 : 1998 : R2010 | Standard Test Method for Tensile Properties of Organic Coatings |
ASTM C 1442 : 2006 | Standard Practice for Conducting Tests on Sealants Using Artificial Weathering Apparatus |
ASTM D 1079 : 2005 : REV A | Terminology Relating to Roofing and Waterproofing |
ASTM D 1079 : 2002 | Standard Terminology Relating to Roofing, Waterproofing, and Bituminous Materials |
ASTM D 1079 : 2001 | Standard Terminology Relating to Roofing, Waterproofing, and Bituminous Materials |
ASTM D 1133 : 2002 | Standard Test Method for Kauri-Butanol Value of Hydrocarbon Solvents |
ASTM C 1442 : 2003 | Standard Practice for Conducting Tests on Sealants Using Artificial Weathering Apparatus |
ASTM D 2370 : 1998 : R2002 | Standard Test Method for Tensile Properties of Organic Coatings |
ASTM C 1305/C1305M : 2016 | Standard Test Method for Crack Bridging Ability of Liquid-Applied Waterproofing Membrane |
ASTM D 412 : 2016 : R2021 | Standard Test Methods for Vulcanized Rubber and Thermoplastic Elastomers—Tension |
ASTM D 1079 : 2000 : REV A | Standard Terminology Relating to Roofing, Waterproofing, and Bituminous Materials |
ASTM G 113 : 2016 | Standard Terminology Relating to Natural and Artificial Weathering Tests of Nonmetallic Materials |
ASTM D 1133 : 2004 | Standard Test Method for Kauri-Butanol Value of Hydrocarbon Solvents |
ASTM D 609 : 2017 | Standard Practice for Preparation of Cold-Rolled Steel Panels for Testing Paint, Varnish, Conversion Coatings, and Related Coating Products |
ASTM C 1442 : 1999 | Standard Practice for Conducting Tests on Sealants Using Artificial Weathering Apparatus |
ASTM D 1079 : 2013 : EDT 1 | Standard Terminology Relating to Roofing and Waterproofing |
ASTM D 2370 : 2016 : R2021 | Standard Test Method for Tensile Properties of Organic Coatings |
ASTM D 1079 : 2009 | Standard Terminology Relating to Roofing and Waterproofing |
ASTM D 1133 : 2009 | Standard Test Method for Kauri-Butanol Value of Hydrocarbon Solvents |
ASTM G 113 : 2022 | Standard Terminology Relating to Natural and Artificial Weathering Tests of Nonmetallic Materials |
ASTM D 1133 : 1997 | Standard Test Method for Kauri-Butanol Value of Hydrocarbon Solvents |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.