ASTM C 989/C989M : 2018 : REV A
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
Standard Specification for Slag Cement for Use in Concrete and Mortars
Hardcopy , PDF
08-03-2024
English
06-02-2019
This specification covers slag cement for use as a cementitious material in concrete and mortar.
1.1This specification covers slag cement for use as a cementitious material in concrete and mortar.
Note 1:The material described in this specification may be used for blending with portland cement to produce a cement meeting the requirements of Specification C595/C595M or as a separate ingredient in concrete or mortar mixtures. The material may also be useful in a variety of special grouts and mortars, and when used with an appropriate activator, as the principal cementitious material in some applications.
Note 2:Information on technical aspects of the use of the material described in this specification is contained in Appendix X1, Appendix X2, and Appendix X3. More detailed information on that subject is contained in ACI 233R-17.2
1.2The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text, the inch-pound units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. Values are stated in only SI units when inch-pound units are not used in practice.
1.3The text of this standard references notes and footnotes that provide explanatory information. These notes and footnotes (excluding those in tables) shall not be considered as requirements of this standard.
1.4The following safety hazards caveat pertains only to the test methods described in this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.5This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| Committee |
C 09
|
| DocumentType |
Standard
|
| Pages |
7
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| ASTM C 1776/C1776M : 2017 : R2022 | Standard Specification for Wet-Cast Precast Modular Retaining Wall Units |
| ASTM C 685/C685M : 2017 | Standard Specification for Concrete Made by Volumetric Batching and Continuous Mixing |
| ASTM C 505M : 2019 | Standard Specification for Nonreinforced Concrete Irrigation Pipe With Rubber Gasket Joints (Metric) |
| ASTM C 1782/C1782M : 2021 | Standard Specification for Segmental Concrete Paving Slabs |
| ASTM C 1765 : 2019 | Standard Specification for Steel Fiber Reinforced Concrete Culvert, Storm Drain, and Sewer Pipe |
| ASTM E 2129 : 2018 | Standard Practice for Data Collection for Sustainability Assessment of Building Products |
| ASTM C 654M : 2019 | Standard Specification for Porous Concrete Pipe (Metric) |
| ASTM C 1433M : 2020 | Standard Specification for Precast Reinforced Concrete Monolithic Box Sections for Culverts, Storm Drains, and Sewers (Metric) |
| ASTM C 913 : 2021 | Standard Specification for Precast Concrete Water and Wastewater Structures |
| ASTM C 506M : 2020 | Standard Specification for Reinforced Concrete Arch Culvert, Storm Drain, and Sewer Pipe (Metric) |
| ASTM C 1504M : 2020 | Standard Specification for Manufacture of Precast Reinforced Concrete Three-Sided Structures for Culverts and Storm Drains (Metric) |
| ASTM C 1293 : 2020 : REV A | Standard Test Method for Determination of Length Change of Concrete Due to Alkali-Silica Reaction |
| ASTM C 1837 : 2022 | Standard Specification for Production of Dry Cast Concrete Used for Manufacturing Pipe, Box, and Precast Structures |
| ASTM C 1417 : 2019 | Standard Specification for Manufacture of Reinforced Concrete Sewer, Storm Drain, and Culvert Pipe for Direct Design |
| ASTM C 1804 : 2020 | Standard Specification for Spun Cast Prestressed Concrete Bases for Tapered Steel Lighting Poles |
| ASTM C 655 : 2019 : REV A | Standard Specification for Reinforced Concrete D-Load Culvert, Storm Drain, and Sewer Pipe |
| ASTM C 1884 : 2019 | Standard Specification for Concrete Ballast Block |
| ASTM C 1904 : 2020 | Standard Test Methods for Determination of the Effects of Biogenic Acidification on Concrete Antimicrobial Additives and/or Concrete Products |
| ASTM C 985 : 2019 | Standard Specification for Nonreinforced Concrete Specified Strength Culvert, Storm Drain, and Sewer Pipe |
| ASTM C 90 : 2022 | Standard Specification for Loadbearing Concrete Masonry Units |
| ASTM C 936/C936M : 2021 : REV B | Standard Specification for Solid Concrete Interlocking Paving Units |
| ASTM D 8021 : 2020 | Standard Guide for Blast Furnace and Steel Furnace Slag as Produced During the Manufacture of Iron and Steel |
| ASTM C 441/C441M : 2017 | Standard Test Method for Effectiveness of Pozzolans or Ground Blast-Furnace Slag in Preventing Excessive Expansion of Concrete Due to the Alkali-Silica Reaction |
| ASTM C 1634 : 2020 | Standard Specification for Concrete Facing Brick and Other Concrete Masonry Facing Units |
| ASTM C 654 : 2019 | Standard Specification for Porous Concrete Pipe |
| ASTM C 1417M : 2019 | Standard Specification for Manufacture of Reinforced Concrete Sewer, Storm Drain, and Culvert Pipe for Direct Design (Metric) |
| ASTM C 1319 : 2021 | Standard Specification for Concrete Grid Paving Units |
| ASTM C 1577 : 2020 : EDT 1 | Standard Specification for Precast Reinforced Concrete Monolithic Box Sections for Culverts, Storm Drains, and Sewers Designed According to AASHTO LRFD |
| ASTM C 505 : 2019 | Standard Specification for Nonreinforced Concrete Irrigation Pipe with Rubber Gasket Joints |
| ASTM C 1504 : 2020 | Standard Specification for Manufacture of Precast Reinforced Concrete Three-Sided Structures for Culverts and Storm Drains |
| ASTM C 14 : 2020 | Standard Specification for Nonreinforced Concrete Sewer, Storm Drain, and Culvert Pipe |
| ASTM C 1903 : 2021 | Standard Specification for Precast Concrete Duct Bank |
| ASTM C 507 : 2020 | Standard Specification for Reinforced Concrete Elliptical Culvert, Storm Drain, and Sewer Pipe |
| ASTM C 109/C109M : 2021 | Standard Test Method for Compressive Strength of Hydraulic Cement Mortars (Using 2-in. or [50mm] Cube Specimens) |
| ASTM C 14M : 2020 | Standard Specification for Nonreinforced Concrete Sewer, Storm Drain, and Culvert Pipe (Metric) |
| ASTM C 1141/C1141M : 2015 | Standard Specification for Admixtures for Shotcrete (Withdrawn 2024) |
| ASTM C 94/C94M : 2022 | Standard Specification for Ready-Mixed Concrete |
| ASTM C 1688/C1688M : 2014 : REV A | Standard Test Method for Density and Void Content of Freshly Mixed Pervious Concrete (Withdrawn 2023) |
| ASTM C 858 : 2019 | Standard Specification for Underground Precast Concrete Utility Structures |
| ASTM C 118M : 2019 | Standard Specification for Concrete Pipe for Irrigation or Drainage (Metric) (Withdrawn 2024) |
| ASTM C 76M : 2022 | Standard Specification for Reinforced Concrete Culvert, Storm Drain, and Sewer Pipe (Metric) |
| ASTM C 412 : 2019 | Standard Specification for Concrete Drain Tile |
| ASTM C 476 : 2020 | Standard Specification for Grout for Masonry |
| ASTM C 506 : 2020 : EDT 1 | Standard Specification for Reinforced Concrete Arch Culvert, Storm Drain, and Sewer Pipe |
| ASTM C 507M : 2020 | Standard Specification for Reinforced Concrete Elliptical Culvert, Storm Drain, and Sewer Pipe (Metric) |
| ASTM C 1786 : 2019 | Standard Specification for Segmental Precast Reinforced Concrete Box Sections for Culverts, Storm Drains, and Sewers Designed According to AASHTO LRFD |
| ASTM C 1697 : 2021 | Standard Specification for Blended Supplementary Cementitious Materials |
| ASTM C 1670/C1670M : 2021 : REV B | Standard Specification for Adhered Manufactured Stone Masonry Veneer Units |
| ASTM C 1778 : 2022 | Standard Guide for Reducing the Risk of Deleterious Alkali-Aggregate Reaction in Concrete |
| ASTM C 1894 : 2022 | Standard Guide for Microbially Induced Corrosion of Concrete Products |
| ASTM C 76 : 2022 | Standard Specification for Reinforced Concrete Culvert, Storm Drain, and Sewer Pipe |
| ASTM C 1433 : 2020 : EDT 1 | Standard Specification for Precast Reinforced Concrete Monolithic Box Sections for Culverts, Storm Drains, and Sewers |
| ASTM C 1846/C1846M : 2019 | Standard Specification for Performance Based Manufacture of Reinforced Concrete Culvert, Storm Drain, and Sewer Pipe |
| ASTM C 118 : 2019 | Standard Specification for Concrete Pipe for Irrigation or Drainage |
| ASTM C 412M : 2019 | Standard Specification for Concrete Drain Tile (Metric) |
| ASTM C 1491 : 2019 | Standard Specification for Concrete Roof Pavers (Withdrawn 2023) |
| ASTM C 1818 : 2022 | Standard Specification for Synthetic Fiber Reinforced Concrete Culvert, Storm Drain, and Sewer Pipe |
| ASTM C 1731 : 2021 | Standard Specification for Concrete Floor Tile |
| ASTM C 1492 : 2022 | Standard Specification for Concrete Roof Tile |
| ASTM C 655M : 2019 : REV A | Standard Specification for Reinforced Concrete D-Load Culvert, Storm Drain, and Sewer Pipe (Metric) |
| ASTM C 125 : 2021 | Standard Terminology Relating to Concrete and Concrete Aggregates |
| ASTM C 1437 : 2001 | Standard Test Method for Flow of Hydraulic Cement Mortar |
| ASTM D 3665 : 2002 | Standard Practice for Random Sampling of Construction Materials |
| ASTM C 452 : 2021 | Standard Test Method for Potential Expansion of Portland-Cement Mortars Exposed to Sulfate |
| ASTM C 452 : 2019 : EDT 1 | Standard Test Method for Potential Expansion of Portland-Cement<brk/> Mortars Exposed to Sulfate |
| ASTM C 109/C109M : 2020 : REV B | Standard Test Method for Compressive Strength of Hydraulic Cement Mortars (Using 2-in. or [50mm] Cube Specimens) |
| ASTM C 465 : 2019 | Standard Specification for Processing Additions for Use in the Manufacture<brk/> of Hydraulic Cements |
| ASTM C 1778 : 2019 | Standard Guide for Reducing the Risk of Deleterious Alkali-Aggregate Reaction in Concrete |
| ASTM C 1437 : 2013 | Standard Test Method for Flow of Hydraulic Cement Mortar |
| ASTM C 595/C595M : 2021 | Standard Specification for Blended Hydraulic Cements |
| ASTM C 1778 : 2016 | Standard Guide for Reducing the Risk of Deleterious Alkali-Aggregate Reaction in Concrete |
| ASTM C 109/C109M : 2021 | Standard Test Method for Compressive Strength of Hydraulic Cement Mortars (Using 2-in. or [50mm] Cube Specimens) |
| ASTM C 125 : 2000 | Standard Terminology Relating to Concrete and Concrete Aggregates |
| ASTM D 3665 : 2012 : R2017 | Standard Practice for Random Sampling of Construction Materials |
| ASTM C 595/C595M : 2020 | Standard Specification for Blended Hydraulic Cements |
| ASTM D 3665 : 2007 | Standard Practice for Random Sampling of Construction Materials |
| ASTM C 150/C150M : 2021 | Standard Specification for Portland Cement |
| ASTM D 3665 : 2012 | Standard Practice for Random Sampling of Construction Materials |
| ASTM C 1778 : 2022 | Standard Guide for Reducing the Risk of Deleterious Alkali-Aggregate Reaction in Concrete |
| ASTM C 1778 : 2014 | Standard Guide for Reducing the Risk of Deleterious Alkali-Aggregate Reaction in Concrete |
| ASTM C 1778 : 2019 : REV B | Standard Guide for Reducing the Risk of Deleterious Alkali-Aggregate Reaction in Concrete |
| ASTM C 114 : 2009 | Standard Test Methods for Chemical Analysis of Hydraulic Cement |
| ASTM C 125 : 2021 : REV A | Standard Terminology Relating to Concrete and Concrete Aggregates |
| ASTM C 1437 : 2007 | Standard Test Method for Flow of Hydraulic Cement Mortar |
| ASTM C 1778 : 2019 : REV A | Standard Guide for Reducing the Risk of Deleterious Alkali-Aggregate Reaction in Concrete |
| ASTM C 1778 : 2020 | Standard Guide for Reducing the Risk of Deleterious Alkali-Aggregate Reaction in Concrete |
| ASTM C 150/C150M : 2020 | Standard Specification for Portland Cement |
| ASTM C 125 : 2020 | Standard Terminology Relating to Concrete and Concrete Aggregates |
| ASTM D 3665 : 2007 : EDT 1 | Standard Practice for Random Sampling of Construction Materials |
| ASTM C 1437 : 2015 | Standard Test Method for Flow of Hydraulic Cement Mortar |
| ASTM D 3665 : 2006 | Standard Practice for Random Sampling of Construction Materials |
| ASTM C 150/C150M : 2022 | Standard Specification for Portland Cement |
| ASTM C 1437 : 1999 | Standard Test Method for Flow of Hydraulic Cement Mortar |
| ASTM C 465 : 2022 | Standard Specification for Processing Additions for Use in the Manufacture<brk/> of Hydraulic Cements |
| ASTM D 3665 : 1999 | Standard Practice for Random Sampling of Construction Materials |
| ASTM C 125 : 2009 | Standard Terminology Relating to Concrete and Concrete Aggregates |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.