• There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

ASTM D 1126 : 1996

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Standard Test Method for Hardness in Water
Superseded date

11-11-2014

Published date

31-12-2010

1.1 This test method covers the determination of hardness in water by titration. This test method is applicable to waters that are clear in appearance and free of chemicals that will complex calcium or magnesium. The lower detection limit of this test method is approximately 2 to 5 mg/L as CaCO3; the upper limit can be extended to all concentrations by sample dilution. It is possible to differentiate between hardness due to calcium ions and that due to magnesium ions by this test method.

1.2 This test method was tested on reagent water only. It is the user's responsibility to ensure the validity of the test method for waters of untested matrices.

1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Committee
D 19
DocumentType
Test Method
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy

ASTM D 5752 : 2010 : R2017 Standard Specification for Supplemental Coolant Additives (SCAs) for Use in Precharging Coolants for Heavy-Duty Engines
ASTM D 7715 : 2012 : R2016 : EDT 1 Standard Specification for Fully-Formulated Glycerin Base Engine Coolant for Heavy-Duty Engines
ASTM D 3376 : 2018 Standard Test Methods of Sampling and Testing Pulps to be Used in the Manufacture of Electrical Insulation
ASTM E 1910/E1910M : 2015 Standard Test Method for Agricultural pH Control Agents, Measurement of pH Change and Buffering Capacity
ASTM D 6469 : 2017 Standard Guide for Microbial Contamination in Fuels and Fuel Systems
ASTM D 8039 : 2016 Standard Specification for Heat Transfer Fluids (HTF) for Heating and Air Conditioning (HVAC) Systems
ASTM D 6210 : 2017 Standard Specification for Fully-Formulated Glycol Base Engine Coolant for Heavy-Duty Engines<rangeref></rangeref >
ASTM E 1391 : 2003 : R2014 Standard Guide for Collection, Storage, Characterization, and Manipulation of Sediments for Toxicological Testing and for Selection of Samplers Used to Collect Benthic Invertebrates
ASTM D 7517 : 2019 Standard Specification for Fully-Formulated 1,3 Propanediol (PDO) Base Engine Coolant for Heavy-Duty Engines
ASTM E 1945 : 2002 : R2016 Standard Test Method for Percent Dispersibility
ASTM C 500/C500M : 2007 : R2019 Standard Test Methods for Asbestos-Cement Pipe (Withdrawn 2022)
ASTM D 1782 : 2017 Standard Test Methods for Operating Performance of Particulate Cation-Exchange Materials
ASTM C 375 : 1958 : R2016 Standard Classification of Water Used in Milling of Porcelain Enamel
ASTM E 1116 : 1998 : R2014 Standard Test Method for Emulsification Characteristics of Pesticide Emulsifiable Concentrates
ASTM D 3342 : 1990 : R2017 Standard Test Method for Dispersion Stability of New (Unused) Rolling Oil Dispersions in Water
ASTM E 1673 : 1996 : R2017 Standard Test Method for Percent Suspensibility
ASTM D 2946 : 2001 : R2018 Standard Terminology for Asbestos and Asbestos–Cement Products (Withdrawn 2022)
ASTM D 4985 : 2010 : R2015 Standard Specification for Low Silicate Ethylene Glycol Base Engine Coolant for Heavy Duty Engines Requiring a Pre-Charge of Supplemental Coolant Additive (SCA)
ASTM D 7518 : 2010 : R2015 : EDT 1 Standard Specification for 1,3 Propanediol (PDO) Base Engine Coolant for Automobile and Light-Duty Service
ASTM D 3306 : 2019 Standard Specification for Glycol Base Engine Coolant for Automobile and Light-Duty Service
ASTM D 7714 : 2011 : R2016 : EDT 1 Standard Specification for Glycerin Base Engine Coolant for Automobile and Light-Duty Service
ASTM E 1116 : 1998(R2019) Standard Test Method for Emulsification Characteristics of Pesticide Emulsifiable Concentrates
ASTM D 3306 : 2020 Standard Specification for Glycol Base Engine Coolant for Automobile and Light-Duty Service
ASTM D 6469 : 2020 Standard Guide for Microbial Contamination in Fuels and Fuel Systems
ASTM D 7518 : 2020 Standard Specification for 1,3 Propanediol (PDO) Base Engine Coolant for Automobile and Light-Duty Service

View more information
Sorry this product is not available in your region.

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.