Standard Test Methods for Testing Solvent Containing Varnishes Used for Electrical Insulation

Available format(s)

PDF

Language(s)

English

Published date

14-11-2017

Publisher

American Society for Testing and Materials

CONTAINED IN VOL. 10.01, 2017 Defines tests for solvent containing varnishes primarily intended to provide electrical, mechanical, and chemical protection for electrical equipment.

1.1These test methods cover tests for solvent containing varnishes primarily intended to provide electrical, mechanical, and chemical protection for electrical equipment. These test methods include tests for control and performance as follows:

Procedure	Section
Build	38 – 42
Dielectric Strength	43 – 48
Drainage	26 – 32
Flash Point	18 – 20
Nonvolatile Matter	21 – 25
Oil Resistance	54 – 56
Preparation of Test Specimens	7
Specific Gravity	9 – 12
Temperature Index	49 – 50
Time of Drying	33 – 37
Varnish Compatibility	51 – 53
Viscosity	13 – 17

1.2Where the entire test method is included in this standard, the precision and bias are not known unless given in the stated method.

1.3The values stated in SI units are to be regarded as standard. The values given in parentheses are for information only.

1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific hazard statements, see Section 5.

Note 1:There is no equivalent IEC standard.

1.5This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Committee	D 09
DevelopmentNote	Supersedes ASTM D 1346 (12/2001)
DocumentType	Redline
Pages	9
PublisherName	American Society for Testing and Materials
Status	Current

DWA-M 143-20:2018	TEST METHOD FOR DROP IMPACT RESISTANCE OF BLOW-MOLDED THERMOPLASTIC CONTAINERS
ASTM D 1304 : 1999	Standard Test Methods for Adhesives Relative to Their Use as Electrical Insulation
ASTM D 3089 : 1997 : R2008	Standard Practice for Determining the A-D Dimension of Aerosol Valve Dip Tubes
ASTM D 3955 : 2013 : REDLINE	Standard Specification for Electrical Insulating Varnishes
TAPPI T 666 : OM 86	VISCOSITY OF ADHESIVES USING A LOW-SHEAR ROTATING APPARATUS
ASTM D 2519 : 2007	Standard Test Method for Bond Strength of Electrical Insulating Varnishes by the Helical Coil Test
ASTM D 2756 : 2007 : R2012	Standard Test Method for Weight Loss of Electrical Insulating Varnishes
MIL-C-47221 Revision A:1982	COMPOUND, MOLDING, EPOXY RESIN, SILICON DIOXIDE AND ASBESTOS FIBER FILL
ASTM D 2756 : 2007	Standard Test Method for Weight Loss of Electrical Insulating Varnishes
DIN 65065:1979-08	AEROSPACE; RESINS FOR FIBER REINFORCED, TECHNICAL SPECIFICATION
ASTM D 1304 : 1999 : R2005	Standard Test Methods for Adhesives Relative to Their Use as Electrical Insulation
ASTM D 1084 : 2016 : REDLINE	Standard Test Methods for Viscosity of Adhesives
ASTM D 2519 : 2007 : R2012	Standard Test Method for Bond Strength of Electrical Insulating Varnishes by the Helical Coil Test
ASTM D 2832 : 1992 : R2016	Standard Guide for Determining Volatile and Nonvolatile Content of Paint and Related Coatings
ASTM D 3251 : 2004 : R2009	Standard Test Method for Thermal Endurance Characteristics of Electrical Insulating Varnishes Applied Over Film-Insulated Magnet Wire
NEMA RE 2:1999	Electrical Insulating Varnish
ASTM D 7230 : 2006 : R2013	Standard Guide for Evaluating Polymeric Lining Systems for Water Immersion in Coating Service Level III Safety-Related Applications on Metal Substrates
ASTM D 1304 : 1999 : R2012	Standard Test Methods for Adhesives Relative to Their Use as Electrical Insulation
ASTM D 4209 : 2007	Standard Practice for Determining Volatile and Nonvolatile Content of Cellulosics, Emulsions, Resin Solutions, Shellac, and Varnishes
ASTM D 3251 : 2004 : R2013	Standard Test Method for Thermal Endurance Characteristics of Electrical Insulating Varnishes Applied Over Film-Insulated Magnet Wire
MIL-E-22118 Revision B:1974	ENAMEL, ELECTRICAL INSULATING
MIL-C-47002 Revision A:1991	COATING, POLYURETHANE, SINGLE COMPONENT SYSTEM
MIL-C-47200 Base Document:1974	WIRE AND CABLE, ELECTRICAL, SINGLE CONDUCTOR, TWISTED PAIRS AND MULTICONDUCTOR SHIELDED AND JACKETED, HIGH TEMPERATURE
ASTM D 4882 : 2017 : REDLINE	Standard Test Method for Bond Strength of Electrical Insulating Varnishes by the Twisted-Coil Test
ASTM D 2832 : 1992 : R1999	Standard Guide for Determining Volatile and Nonvolatile Content of Paint and Related Coatings
ASTM D 7230 : 2006	Standard Guide for Evaluating Polymeric Lining Systems for Water Immersion in Coating Service Level III Safety-Related Applications on Metal Substrates
GOST 849:2018	Primary nickel. SpecificationsE
MIL-I-24092 Revision D:1993	INSULATING VARNISHES AND SOLVENTLESS RESINS FOR APPLICATION BY THE DIP PROCESS
ASTM D 2832 : 1992 : R2005	Standard Guide for Determining Volatile and Nonvolatile Content of Paint and Related Coatings
MIL-P-16406 Revision A:1974	PAINT, BLACK, HIGH GLOSS, QUICK DRYING
ASTM D 2756 : 2007 : R2017	Standard Test Method for Weight Loss of Electrical Insulating Varnishes
ASTM D 4209 : 2007 : R2013	Standard Practice for Determining Volatile and Nonvolatile Content of Cellulosics, Emulsions, Resin Solutions, Shellac, and Varnishes
ASTM D 3251 : 2004	Standard Test Method for Thermal Endurance Characteristics of Electrical Insulating Varnishes Applied Over Film-Insulated Magnet Wire
ASTM D 2832 : 1992 : R2011	Standard Guide for Determining Volatile and Nonvolatile Content of Paint and Related Coatings

ASTM D 295 : 2012	Standard Test Methods for Varnished Cotton Fabrics Used for Electrical Insulation (Withdrawn 2020)
ASTM D 580 : 2004	Standard Specification for Greige Woven Glass Tapes and Webbings
ASTM D 202 : 2017 : REDLINE	Standard Test Methods for Sampling and Testing Untreated Paper Used for Electrical Insulation
ASTM D 93 : 2016-07	TEST METHODS FOR FLASH POINT BY PENSKY-MARTENS CLOSED CUP TESTER
ASTM E 104 : 2002	Standard Practice for Maintaining Constant Relative Humidity by Means of Aqueous Solutions
ASTM D 1475 : 2013 : REDLINE	Standard Test Method For Density of Liquid Coatings, Inks, and Related Products
ASTM D 374 : 1999	Standard Test Methods for Thickness of Solid Electrical Insulation
ASTM D 5423 : 2014	Standard Specification for Forced-Convection Laboratory Ovens for Evaluation of Electrical Insulation

View more information

£62.61

Excluding VAT

Product format

I agree to the DRM document license rules apply against the PDF selection made.

Please confirm that you agree to the document license rules for this document.

I agree to the document license rules .

Please confirm that you agree to the document license rules for this document.

Access your standards online with a subscription

Features

Simple online access to standards, technical information and regulations.
Critical updates of standards and customisable alerts and notifications.
Multi-user online standards collection: secure, flexible and cost effective.

Learn more on subscription solutions

Get in touch with us

ASTM D 115 : 2017 : REDLINE

Standard Test Methods for Testing Solvent Containing Varnishes Used for Electrical Insulation

Abstract

Scope

General Product Information

Standards Referenced By This Book

Standards Referencing This Book

Category

Subcategory