ASTM D 1177 : 2017 : REDLINE
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
Standard Test Method for Freezing Point of Aqueous Engine Coolants
28-09-2022
English
12-04-2017
CONTAINED IN VOL. 15.05, 2017 Specifies the determination of the freezing point of an aqueous engine coolant solution in the laboratory.
1.1This test method covers the determination of the freezing point of an aqueous engine coolant solution in the laboratory.
Note 1:Where solutions of specific concentrations are to be tested, they shall be prepared from representative samples as directed in Practice D1176. Secondary phases separating on dilution need not be separated.
Note 2:These products may also be marketed in a ready-to-use form (prediluted).
1.2The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.
1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
1.4This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| Committee |
D 15
|
| DocumentType |
Redline
|
| Pages |
4
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy |
| 14/30301257 DC : 0 | BS EN 13160-3 - LEAK DETECTION SYSTEMS - PART 3: REQUIREMENTS AND TEST/ASSESSMENT METHODS FOR LIQUID SYSTEMS FOR TANKS |
| SAE ARP 6207 : 2017 | QUALIFICATIONS REQUIRED FOR SAE TYPE 1 AIRCRAFT DEICING/ANTI-ICING FLUIDS |
| O-A-548 Revision D:1974 | ANTIFREEZE COOLANT, ENGINE, ETHYLENE GLYCOL, INHIBITED, CONCENTRATED |
| SAE J 814 : 2018 | COOLANTS FOR INTERNAL COMBUSTION ENGINES |
| ASTM D 6660 : 2001 | Standard Test Method for Freezing Point of Aqueous Ethylene Glycol Base Engine Coolants by Automatic Phase Transition Method |
| DIN EN 14291 E : 2005 | FOAM PRODUCING SOLUTIONS FOR LEAK DETECTION ON GAS INSTALLATIONS |
| BS EN 14291:2004 | Foam producing solutions for leak detection on gas installations |
| EN 13160-3:2016 | Leak detection systems - Part 3: Requirements and test/assessment methods for liquid systems for tanks |
| DEFSTAN 68-118/2(1997) : 1997 | DE-ICING/ANTI-ICING FLUID FOR RUNWAYS |
| DEFSTAN 68-118/3(2002) : 2002 | DE-ICING/ANTI-ICING FLUID FOR RUNWAYS |
| DEFSTAN 68-147/2(2002) : 2002 | LIQUID CLEANER FOR USE ON AIRCRAFT TRANSPARENCIES |
| DEFSTAN 68-118(PT1)/1(2005) : 2005 | PART 1: DE-ICING FLUID FOR AIRFIELDS AND FLIGHT DECKS |
| SAE AMS 1426 : 2016 | FLUID, DEICING/ANTI-ICING, RUNWAYS AND TAXIWAYS GLYCOL BASE |
| ASTM D 5216 : 1998 | Standard Specification for Propylene Glycol Base Engine Coolant for Automobile and Light-Duty Service (Withdrawn 2000) |
| 09/30163562 DC : DRAFT SEP 2009 | BS 6580 AMD2 - SPECIFICATION FOR CORROSION INHIBITING, ENGINE COOLANT CONCENTRATE ('ANTIFREEZE') |
| SAE AMS 1428 : 2017 | FLUID, AIRCRAFT DEICING/ANTI-ICING, NON-NEWTONIAN, (PSEUDOPLASTIC), SAE TYPES 2, 3 AND 4 |
| SAE ARP 5718 : 2017 | Qualifications Required for SAE Type II/III/IV Aircraft Deicing/Anti-Icing Fluid |
| DEFSTAN 68-217/1(1993) : INTERIM | ICE CONTROL AGENTS FOR AIRCRAFT RUNWAYS |
| ASTM D 4656 : 1998 | Standard Specification for Prediluted Aqueous Ethylene Glycol Base Engine Coolant (50 Volume % Minimum) for Automobiles and Light-Duty Service (Withdrawn 2000) |
| ASTM D 3585 : 2008 | Standard Specification for ASTM Reference Fluid for Coolant Tests |
| ASTM D 3585 : 2008 : R2013 | Standard Specification for ASTM Reference Fluid for Coolant Tests |
| ASTM D 6660 : 2001 : R2019 | Standard Test Method for Freezing Point of Aqueous Ethylene Glycol Base Engine Coolants by Automatic Phase Transition Method |
| ASTM D 4985 : 2010 | Standard Specification for Low Silicate Ethylene Glycol Base Engine Coolant for Heavy Duty Engines Requiring a Pre-Charge of Supplemental Coolant Additive (SCA) |
| ASTM D 345 : 2002 | Side bearings of the freight wagon bogies. General specifications |
| I.S. EN 13160-3:2016 | LEAK DETECTION SYSTEMS - PART 3: REQUIREMENTS AND TEST/ASSESSMENT METHODS FOR LIQUID SYSTEMS FOR TANKS |
| MIL-T-37402 Base Document:1977 | TESTER, ANTIFREEZE, SOLUTIONS |
| ASTM D 6660 : 2001 : R2007 | Standard Test Method for Freezing Point of Aqueous Ethylene Glycol Base Engine Coolants by Automatic Phase Transition Method |
| MIL-PRF-25567 Revision E:1998 | LEAK DETECTION COMPOUND, OXYGEN SYSTEMS |
| ASTM D 6660 : 2001 : R2014 : EDT 1 | Standard Test Method for Freezing Point of Aqueous Ethylene Glycol Base Engine Coolants by Automatic Phase Transition Method |
| SAE AMS 1424 : 2017 | FLUID, AIRCRAFT DEICING/ANTI-ICING, SAE TYPE 1 |
| ASTM D 3306 : 2014-05 | SPECIFICATION FOR GLYCOL BASE ENGINE COOLANT FOR AUTOMOBILE AND LIGHT-DUTY SERVICE |
| ASTM D 7583 : 2016 : REDLINE | Standard Test Method for John Deere Coolant Cavitation Test |
| ASTM D 8039 : 2016 | Standard Specification for Heat Transfer Fluids (HTF) for Heating and Air Conditioning (HVAC) Systems |
| ASTM D 7714 : 2011 | Standard Specification for Glycerin Base Engine Coolant for Automobile and Light-Duty Service |
| ASTM D 6257 : 1998 | Standard Specification for Prediluted Aqueous Propylene Glycol Base Engine Coolant (50 Volume % Minimum) for Automobile and Light-Duty Service (Withdrawn 2000) |
| ASTM D 5345 : 1998 | Standard Specification for Prediluted Aqueous Ethylene Glycol Base Low-Silicate Engine Coolant (50 Volume % Minimum) for Heavy-Duty Engines Requiring an Initial Charge of Supplemental Coolant Additive (SCA) (Withdrawn 2000) |
| BS 6580:2010 | Specification for corrosion inhibiting, engine coolant concentrate (\'antifreeze\') |
| BS 6846:1987 | Specification for rubber hoses and hose assemblies for use in oil burners |
| MIL-C-52947 Revision B:1986 | COAGULANT, WATER TREATMENT: POLYELECTROLYTE, CATIONIC, LIQUID |
| CSA C448 SERIES : 2016 | DESIGN AND INSTALLATION OF GROUND SOURCE HEAT PUMP SYSTEMS FOR COMMERCIAL AND RESIDENTIAL BUILDINGS |
| MIL-D-83411 Revision A:1973 | DEICER/ANTI-ICER FLUID (FOR RUNWAYS AND TAXIWAYS) |
| DEFSTAN 68-118/1(1993) : INTERIM | DEICING & ANTI ICING FLUID FOR RUNWAYS |
| ASTM D 7518 : 2010 | Standard Specification for 1,3 Propanediol (PDO) Base Engine Coolant for Automobile and Light-Duty Service |
| SAE AMS 1432 : 1995 | FLUID, DEICING/ANTI-ICING, RUNWAYS AND TAXIWAYS, POTASSIUM ACETATE BASE |
| ASTM D 7714 : 2011 : R2016 : EDT 1 | Standard Specification for Glycerin Base Engine Coolant for Automobile and Light-Duty Service |
| ASTM D 6660 : 2001 : EDT 1 | Standard Test Method for Freezing Point of Aqueous Ethylene Glycol Base Engine Coolants by Automatic Phase Transition Method |
| UNE-EN 13160-3:2017 | Leak detection systems - Part 3: Requirements and test/assessment methods for liquid systems for tanks |
| EN 14291:2004 | Foam producing solutions for leak detection on gas installations |
| PREN 13160-3 : DRAFT 2014 | LEAK DETECTION SYSTEMS - PART 3: REQUIREMENTS AND TEST/ASSESSMENT METHODS FOR LIQUID SYSTEMS FOR TANKS |
| MIL-A-11755 Revision E:1994 | ANTIFREEZE, ARCTIC-TYPE |
| CGSB 3.532 : M85 | ANTIFREEZE, WINDSHIELD WASHER, METHANOL BASE |
| MIL L 25567 : D | LEAK DETECTION COMPOUND, OXYGEN SYSTEMS (METRIC) |
| SAE AMS 1435 : 2012 | FLUID, GENERIC, DEICING/ANTI-ICING, RUNWAYS AND TAXIWAYS |
| ASTM D 7518 : 2010 : R2015 : EDT 1 | Standard Specification for 1,3 Propanediol (PDO) Base Engine Coolant for Automobile and Light-Duty Service |
| DEFSTAN 68-147/1(1996) : 1996 | LIQUID CLEANER; FOR USE ON AIRCRAFT TRANSPARENCIES |
| ASTM D 4985 : 2010 : R2015 | Standard Specification for Low Silicate Ethylene Glycol Base Engine Coolant for Heavy Duty Engines Requiring a Pre-Charge of Supplemental Coolant Additive (SCA) |
| DIN EN 14291:2005-02 | Foam producing solutions for leak detection on gas installations; German version EN 14291:2004 |
| ASTM E 1 : 2014 : REDLINE | Standard Specification for ASTM Liquid-in-Glass Thermometers |
| ASTM D 1176 : 2014 : REDLINE | Standard Practice for Sampling and Preparing Aqueous Solutions of Engine Coolants or Antirusts for Testing Purposes |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.