We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
  • ASTM D 1183 : 2003 : R2011

    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    Add to Watchlist
    This Standard has been added successfully to your Watchlist.
    Please visit My Watchlist to see all standards that you are watching.
    Please log in or to add this standard to your Watchlist.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    You need to be logged in to add this standard to your Watchlist.
    Please log in now or create an account to add.
    You already added this Product in the Watchlist.

    Standard Practices for Resistance of Adhesives to Cyclic Laboratory Aging Conditions

    Available format(s):  Hardcopy, PDF

    Superseded date:  26-04-2019

    Language(s):  English

    Published date:  01-04-2011

    Publisher:  American Society for Testing and Materials

    Add to Watchlist

    Add To Cart

    Abstract - (Show below) - (Hide below)

    CONTAINED IN VOL. 15.06, 2015 Describes the resistance of adhesives to cyclic accelerated service conditions by exposing bonded specimens to conditions of high and low temperatures and high and low relative humidities.

    Scope - (Show below) - (Hide below)

    1.1 These practices cover the determination of the resistance of adhesives to cyclic accelerated service conditions by exposing bonded specimens to conditions of high and low temperatures and high and low relative humidities. The extent of degradation is determined from changes in strength properties as a result of exposure to the test conditions (Note 1). It is recognized that no accelerated procedure for degrading materials correlates perfectly with actual service conditions, and that no single or small group of laboratory test conditions will simulate all actual service conditions. Consequently, care must be exercised in the interpretation and use of data obtained in this practice. The test condition, the number of cycles of the test condition to be used, the particular strength property to be used to determine the extent of degradation, and whether test specimens or test panels are to be used, is specified in the material specification.

    Note 1—These practices/conditions are intended for use with specimens described in the approved ASTM strength test methods for adhesives as follows:

    Test Methods D897, D903, D906, D950, D1002, D1062, and Method .

    1.2 The values stated in SI units are to be regarded as the standard.

    1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

    General Product Information - (Show below) - (Hide below)

    Committee D 14
    Document Type Standard Practice
    Product Note Reconfirmed 2011
    Publisher American Society for Testing and Materials
    Status Superseded
    Superseded By
    Supersedes

    Standards Referenced By This Book - (Show below) - (Hide below)

    ASTM D 7469 : 2016 Standard Test Methods for End-Joints in Structural Wood Products
    ASTM D 7793 : 2017 Standard Specification for Insulated Vinyl Siding
    ASTM D 6465 : 1999 : R2016 Standard Guide for Selecting Aerospace and General Purpose Adhesives and Sealants
    ASTM D 7446 : 2009 : R2017 Standard Specification for Structural Insulated Panel (SIP) Adhesives for Laminating Oriented Strand Board (OSB) to Rigid Cellular Polystryene Thermal Insulation Core Materials
    ASTM D 4896 : 2001 : R2016 Standard Guide for Use of Adhesive-Bonded Single Lap-Joint Specimen Test Results

    Standards Referencing This Book - (Show below) - (Hide below)

    ASTM D 1141 : 1998 : EDT 1 Standard Practice for the Preparation of Substitute Ocean Water
    ASTM D 1344 : 1978 Methods of Testing Cross-Lap Specimens for Tensile Properties of Adhesives (Withdrawn 1985)
    ASTM D 907 : 2015 : REDLINE Standard Terminology of Adhesives
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective