We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
  • ASTM D 1621 : 2004 : REV A

    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    Add to Watchlist
    This Standard has been added successfully to your Watchlist.
    Please visit My Watchlist to see all standards that you are watching.
    Please log in or to add this standard to your Watchlist.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    You need to be logged in to add this standard to your Watchlist.
    Please log in now or create an account to add.
    You already added this Product in the Watchlist.

    Standard Test Method for Compressive Properties Of Rigid Cellular Plastics

    Available format(s):  Hardcopy, PDF

    Superseded date:  11-11-2014

    Language(s):  English

    Published date:  01-10-2004

    Publisher:  American Society for Testing and Materials

    Add to Watchlist

    Add To Cart

    Scope - (Show below) - (Hide below)

    1.1 This test method describes a procedure for determining the compressive properties of rigid cellular materials, particularly expanded plastics.

    1.2 The values stated in SI units are to be regarded as the standard. The values in brackets are for information only.

    1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

    Note 1—This test method and ISO 844 are technically equivalent.

    General Product Information - (Show below) - (Hide below)

    Committee D 20
    Document Type Test Method
    Publisher American Society for Testing and Materials
    Status Superseded
    Superseded By
    Supersedes

    Standards Referenced By This Book - (Show below) - (Hide below)

    ASTM C 1594 : 2011 : R2017 Standard Specification for Polyimide Rigid Cellular Thermal Insulation
    ASTM C 1029 : 2015 Standard Specification for Spray-Applied Rigid Cellular Polyurethane Thermal Insulation
    ASTM F 2883 : 2011 Standard Guide for Characterization of Ceramic and Mineral Based Scaffolds used for Tissue-Engineered Medical Products (TEMPs) and as Device for Surgical Implant Applications (Withdrawn 2020)
    ASTM F 755 : 1999 : R2011 Standard Specification for Selection of Porous Polyethylene for Use in Surgical Implants
    ASTM E 1975 : 2018 Standard Specification for Shelter, Electrical, Equipment S-280/G
    ASTM C 591 : 2019 Standard Specification for Unfaced Preformed Rigid Cellular Polyisocyanurate Thermal Insulation
    ASTM D 7826 : 2019 Standard Guide for Evaluation of New Aviation Gasolines and New Aviation Gasoline Additives
    ASTM C 447 : 2015 Standard Practice for Estimating the Maximum Use Temperature of Thermal Insulations
    ASTM C 578 : 2019 Standard Specification for Rigid, Cellular Polystyrene Thermal Insulation
    ASTM F 2150 : 2013 Standard Guide for Characterization and Testing of Biomaterial Scaffolds Used in Tissue-Engineered Medical Products
    ASTM D 7119/D7119M : 2013 : REV A Standard Guide for Sampling Spray Polyurethane Foam and Coating in Roofing
    ASTM D 7361 : 2007 : R2018 Standard Test Method for Accelerated Compressive Creep of Geosynthetic Materials Based on Time-Temperature Superposition Using the Stepped Isothermal Method
    ASTM F 1839 : 2008 : R2016 Standard Specification for Rigid Polyurethane Foam for Use as a Standard Material for Testing Orthopaedic Devices and Instruments
    ASTM F 561 : 2019 Standard Practice for Retrieval and Analysis of Medical Devices, and Associated Tissues and Fluids
    ASTM C 1289 : 2018 : REV A Standard Specification for Faced Rigid Cellular Polyisocyanurate Thermal Insulation Board
    ASTM D 7425/D7425M : 2013 Standard Specification for Spray Polyurethane Foam Used for Roofing Applications
    ASTM D 6817/D6817M : 2017 Standard Specification for Rigid Cellular Polystyrene Geofoam
    ASTM C 1512 : 2010 : R2015 : EDT 1 Standard Test Method for Characterizing the Effect of Exposure to Environmental Cycling on Thermal Performance of Insulation Products
    ASTM C 1126 : 2019 Standard Specification for Faced or Unfaced Rigid Cellular Phenolic Thermal Insulation
    ASTM C 1696 : 2016 Standard Guide for Industrial Thermal Insulation Systems
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective