• There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

ASTM D 1653 : 2013 : REDLINE

Current
Current

The latest, up-to-date edition.

Standard Test Methods for Water Vapor Transmission of Organic Coating Films
Available format(s)

PDF

Language(s)

English

Published date

01-06-2013

CONTAINED IN VOL. 06.01, 2017 Defines the determination of the rate at which water vapor passes through films of paint, varnish, lacquer, and other organic coatings.

1.1These test methods cover the determination of the rate at which water vapor passes through films of paint, varnish, lacquer, and other organic coatings. The films may be free films or they may be applied to porous substrates.

1.2A similar, but more generally applicable test method is Test Methods E96 which should be considered when other materials are involved.

1.3Two test methods are covered in Test Methods D1653 as follows:

1.3.1Test Method A—Dry Cup Method, and

1.3.2Test Method B—Wet (Payne) Cup Method.

1.3.3Agreement should not be expected between results obtained by different methods or test conditions. The method that most closely approaches the conditions of use should be selected.

1.4The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. Factors for conversion are stated in 13.2.1.2 and 13.2.2.2.

1.5There are instruments on the market that purport to measure water vapor transmission of films more easily and rapidly than the methods described in Test Methods D1653 and E96. They run essentially the same kinds of tests as in the ASTM methods, but do so instrumentally. However, it appears that no side-by-side tests have been run comparing results from measurements with such instruments to these ASTM methods for precision and accuracy.

1.6This standard does not purport to address the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Committee
D 01
DocumentType
Redline
Pages
7
PublisherName
American Society for Testing and Materials
Status
Current

ASTM C 156 : 2017 : REDLINE Standard Test Method for Water Loss [from a Mortar Specimen] Through Liquid Membrane-Forming Curing Compounds for Concrete
ASTM D 6083 : 2005 : EDT 1 Standard Specification for Liquid Applied Acrylic Coating Used in Roofing (Withdrawn 2014)
SSPC-PAINT 44 : 2013 LIQUID-APPLIED ORGANIC POLYMERIC COATINGS AND LININGS FOR CONCRETE STRUCTURES IN MUNICIPAL WASTEWATER FACILITIES, PERFORMANCE-BASED
NACE TM 01 05 : 2016 EVALUATION OF COATINGS CONTAINING CONDUCTIVE CARBON PIGMENTATION FOR USE AS AN ANODE ON ATMOSPHERICALLY EXPOSED REINFORCED CONCRETE
ASTM E 1795 : 2017 : REDLINE Standard Specification for Non-Reinforced Liquid Coating Encapsulation Products for Leaded Paint in Buildings
ASTM D 6947 : 2007 Standard Specification for Liquid Applied Moisture Cured Polyurethane Coating Used in Spray Polyurethane Foam Roofing System
ASTM E 1797 : 2012 Standard Specification for Reinforced Liquid Coating Encapsulation Products for Leaded Paint in Buildings
ASTM D 6083 : 2005 Standard Specification for Liquid Applied Acrylic Coating Used in Roofing
ASTM D 3105 : 2017 : REDLINE Standard Index of Methods for Testing Elastomeric and Plastomeric Roofing and Waterproofing Materials
ASTM D 16 : 2016 : REDLINE TERMINOLOGY FOR PAINT, RELATED COATINGS, MATERIALS, AND APPLICATIONS
SS-S-1996 Base Document:1976 SEALER, WATER AND WEATHER RESISTANT, FOR ASPHALT, CONCRETE, AND MASONRY SURFACES
CSA Z662 PACKAGE : 2011 CONSISTS OF Z662-11, OIL AND GAS PIPELINE SYSTEMS AND Z662.1-11, COMMENTARY ON CSA Z662-11, OIL AND GAS PIPELINE SYSTEMS
AASHTO T 155 : 2013(R2017) METHOD OF TEST FOR WATER RETENTION BY LIQUID MEMBRANE-FORMING CURING COMPOUNDS FOR CONCRETE
ASTM D 6947/D6947M : 2016 : REDLINE Standard Specification for Liquid Applied Moisture Cured Polyurethane Coating Used in Spray Polyurethane Foam Roofing System
CAN/CSA-Z662-15 Oil and gas pipeline systems
SSPC-PAINT 46 : 2015 ELASTOMERIC, WATER BASED, HIGH BUILD, FLAT, PERFORMANCE-BASED COATING FOR MASONRY AND CONCRETE
ASTM D 4712 : 1987 : REV A : R1996 Standard Guide for Testing Industrial Water-Reducible Coatings
ASTM D 4712 : 1987 : REV A : R2001 Standard Guide for Testing Industrial Water-Reducible Coatings
TT-C-535 Revision B:1972 COATING EPOXY, TWO COMPONENT, FOR INTERIOR USE ON METAL, WOOD, WALLBOARD, PAINTED SURFACES CONCRETE AND MASONRY
CGSB 1.501 : M89 METHOD FOR PERMEANCE OF COATED WALLBOARD
ASTM D 6947 : 2007 : R2013 Standard Specification for Liquid Applied Moisture Cured Polyurethane Coating Used in Spray Polyurethane Foam Roofing System
ASTM D 6577 : 2015 : REDLINE Standard Guide for Testing Industrial Protective Coatings
ASTM D 4712 : 1987 : REV A : R2005 Standard Guide for Testing Industrial Water-Reducible Coatings (Withdrawn 2014)
ASTM E 1797 : 2012 : R2017 : EDT 1 Standard Specification for Reinforced Liquid Coating Encapsulation Products for Leaded Paint in Buildings
ASTM D 4708 : 2012 : REDLINE Standard Practice for Preparation of Uniform Free Films of Organic Coatings

ASTM D 823 : 1995 Standard Practices for Producing Films of Uniform Thickness of Paint, Varnish, and Related Products on Test Panels
ASTM E 104 : 2002 Standard Practice for Maintaining Constant Relative Humidity by Means of Aqueous Solutions
ASTM D 4708 : 2012 : REDLINE Standard Practice for Preparation of Uniform Free Films of Organic Coatings

View more information
£62.61
Excluding VAT

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.