Standard Test Methods for Apparent Density, Bulk Factor, and Pourability of Plastic Materials

Available format(s)

PDF

Language(s)

English

Published date

01-09-2017

Publisher

American Society for Testing and Materials

CONTAINED IN VOL. 08.01, 2017 Describes the measurement of apparent density, bulk factor, and where applicable, the pourability of plastic materials such as molding powders.

1.1These test methods cover the measurement of apparent density, bulk factor, and where applicable, the pourability of plastic materials such as molding powders. Different procedures are given for application to the various forms of these materials that are commonly encountered, from fine powders and granules to large flakes and cut fibers.

1.2The values stated in SI units are to be regarded as the standard. The values in parentheses are for information only.

1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health and environmental practices and determine the applicability of regulatory limitations prior to use.

Note 1:Test Method A is equivalent to ISO Method R 60 as described in the appendix. Test Method C is identical with ISO Method R 61.

1.4This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Committee	D 20
DocumentType	Redline
Pages	8
PublisherName	American Society for Testing and Materials
Status	Current

ASTM D 6881/D6881M : 2003 : R2008 : EDT 1	Standard Classification for Standard Plastics Industry Bulk Box/Pallet Unit Size Classified By Bulk Density
MIL-PRF-24667 Revision C:2008	COATING SYSTEM, NON-SKID, FOR ROLL, SPRAY, OR SELF-ADHERING APPLICATION
DOD-D-51524 Base Document:1986	DYE, DISPERSE BLUE 3 (METRIC)
ASTM D 1457 : 1992	Specification for Polytetrafluorethylene (PTFE) Molding and Extrusion Materials (Withdrawn 1996)
16/30338304 DC : 0	BS ISO/ASTM 52903-1 - ADDITIVE MANUFACTURING - STANDARD SPECIFICATION FOR MATERIAL EXTRUSION BASED ADDITIVE MANUFACTURING OF PLASTIC MATERIALS - PART 1: FEEDSTOCK MATERIALS
MIL-DTL-51522 Revision A:2010	DYE, DISPERSE RED 11 (METRIC)
MIL-S-14374 Revision C:1983	SILICA GEL, IRON FREE
DOD-D-51486 Revision A:1986	DYE MIX, GREEN SMOKE 7
ASTM E 1099 : 1996	Standard Specification for Soda Ash, Anhydrous (Sodium Carbonate, Anhydrous) (Withdrawn 2001)
ASTM D 3214 : 1996	Standard Test Methods for Coating Powders and Their Coatings Used for Electrical Insulation (Withdrawn 2002)
DOD D 51485 : A	DYE, SOLVENT YELLOW 33 (METRIC)
MIL-DTL-3691 Revision E:2006	DYE MIX, VIOLET
ASTM D 704 : 1999	Standard Specification for Melamine-Formaldehyde Molding Compounds
MIL-D-3718 Revision C:1986	DYE MIX, DISPERSE RED 9 - DEXTRIN (METRIC)
ASTM D 704 : 1999 : R2012	Standard Specification for Melamine-Formaldehyde Molding Compounds
ASTM D 704 : 1999 : R2004	Standard Specification for Melamine-Formaldehyde Molding Compounds
ASTM D 345 : 2002	Side bearings of the freight wagon bogies. General specifications
SAE AMS 3753 : 2016	MICROSPHERES, CARBON, HOLLOW
ASTM D 2474 : 1992	Specification for Vinyl Chloride Copolymer Resins (Withdrawn 1999)
MIL-D-20550 Revision B:1968	DIATOMACEOUS EARTH
MIL-DTL-51523 Revision A:2010	DYE, SOLVENT RED 1 (METRIC)
ASTM D 3451 : 2006	Standard Guide for Testing Coating Powders and Powder Coatings
ASTM D 6881 : 2003	Standard Classification for Standard Plastics Industry Bulk Box/Pallet Unit Size Classified By Bulk Density
MIL-M-46891 Revision A:1980	MOLDING COMPOUND, PHENOLIC RESIN, ASBESTOS REINFORCED
MIL-DTL-3284 Revision F:2006	Dye, Disperse Red 9
ASTM D 6881/D6881M : 2003 : R2013	Standard Classification for Standard Plastics Industry Bulk Box/Pallet Unit Size Classified By Bulk Density
MIL-DTL-51485 Revision B:2006	DYE, SOLVENT YELLOW 33
DOD D 51522 : 0	DYE, DISPERSE RED 11 (METRIC)
ASTM D 3451 : 2006 : R2012	Standard Guide for Testing Coating Powders and Powder Coatings
ASTM D 1755 : 2015 : REDLINE	Standard Specification for Poly(Vinyl Chloride) Resins
MIL-T-50036 Revision B:1992	TALC, TECHNICAL, T1 AND T3
MIL-DTL-3277 Revision F:2006	Dye, Solvent Green 3
MIL-DTL-3668 Revision E:2006	Dye, 1,4-Diamino-2,3-Dihydroanthraquinone (Blue)
ASTM D 3451 : 2006 : R2017	Standard Guide for Testing Coating Powders and Powder Coatings

ASTM D 792 : 2013 : REDLINE	Standard Test Methods for Density and Specific Gravity (Relative Density) of Plastics by Displacement
ISO 60:1977	Plastics — Determination of apparent density of material that can be poured from a specified funnel
ISO 61:1976	Plastics — Determination of apparent density of moulding material that cannot be poured from a specified funnel

View more information

£62.61

Excluding VAT

Product format

I agree to the DRM document license rules apply against the PDF selection made.

Please confirm that you agree to the document license rules for this document.

I agree to the document license rules .

Please confirm that you agree to the document license rules for this document.

Access your standards online with a subscription

Features

Simple online access to standards, technical information and regulations.
Critical updates of standards and customisable alerts and notifications.
Multi-user online standards collection: secure, flexible and cost effective.

Learn more on subscription solutions

Get in touch with us

ASTM D 1895 : 2017 : REDLINE

Standard Test Methods for Apparent Density, Bulk Factor, and Pourability of Plastic Materials

Abstract

Scope

General Product Information

Standards Referenced By This Book

Standards Referencing This Book

Category

Subcategory