• There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

ASTM D 2007 : 2011

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Standard Test Method for Characteristic Groups in Rubber Extender and Processing Oils and Other Petroleum-Derived Oils by the Clay-Gel Absorption Chromatographic Method
Available format(s)

Hardcopy , PDF

Superseded date

11-11-2014

Language(s)

English

Published date

01-05-2011

CONTAINED IN VOL. 05.01, 2015 Defines a procedure for classifying oil samples of initial boiling point of at least 260 degrees C (500 degrees F) into the hydrocarbon types of polar compounds, aromatics and saturates, and recovery of representative fractions of these types.

1.1 This test method covers a procedure for classifying oil samples of initial boiling point of at least 260°C (500°F) into the hydrocarbon types of polar compounds, aromatics and saturates, and recovery of representative fractions of these types. This classification is used for specification purposes in rubber extender and processing oils.

Note 1—See Test Method D2226.

1.2 This test method is not directly applicable to oils of greater than 0.1 mass % pentane insolubles. Such oils can be analyzed after removal of these materials, but precision is degraded (see Appendix X1).

1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.

1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Specific warning statements are given in 6.1, Section 7, A1.4.1, and A1.5.5.

Committee
D 02
DocumentType
Test Method
Pages
8
ProductNote
Reconfirmed 2011
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy
Supersedes

ASTM D 2140 : 2008 : R2017 Standard Practice for Calculating Carbon-Type Composition of Insulating Oils of Petroleum Origin
ASTM D 4552/D4552M : 2010 : R2016 : EDT 1 Standard Practice for Classifying Hot-Mix Recycling Agents
ASTM D 7419 : 2018 Standard Test Method for Determination of Total Aromatics and Total Saturates in Lube Basestocks by High Performance Liquid Chromatography (HPLC) with Refractive Index Detection
ASTM D 2549 : 2002 : R2017 Standard Test Method for Separation of Representative Aromatics and Nonaromatics Fractions of High-Boiling Oils by Elution Chromatography
ASTM D 5900 : 2017 : EDT 1 Standard Specification for Physical and Chemical Properties of Industry Reference Materials (IRM)
ASTM D 2864 : 2019 Standard Terminology Relating to Electrical Insulating Liquids and Gases
ASTM D 6074 : 2015 Standard Guide for Characterizing Hydrocarbon Lubricant Base Oils
ASTM D 2226 : 1993 : R2018 Standard Classification for Various Types of Petroleum Oils for Rubber Compounding Use

ASTM D 5309 : 2017 : REDLINE Standard Specification for Cyclohexane 999

View more information
£62.61
Excluding VAT

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.