• There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

ASTM D 2093 : 2003

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Standard Practice for Preparation of Surfaces of Plastics Prior to Adhesive Bonding
Available format(s)

Hardcopy , PDF

Superseded date

11-11-2014

Language(s)

English

Published date

10-04-2003

CONTAINED IN VOL. 15.06, 2017 Specifies surface preparations for plastic adherends, to be used prior to adhesive bonding of test specimens.

1.1 This practice describes surface preparations for plastic adherends, to be used prior to adhesive bonding of test specimens. It should be noted, however, that this practice specifies only the pretreating conditions of the plastic and does not cover the preparation of test specimens, testing conditions, or evaluation of tests. These are covered in the various ASTM test methods or specifications for specific materials.

1.2 Physical Treatments (for example, sanding and solvent wiping) are used in order to remove the glossy finish and all traces of dirt, grease, mold release, or other contaminants from the bonding surfaces.

1.3 Chemical Treatments (for example, sulfuric aciddichromate solution and sodium naphthalene complex) are used in some cases to alter chemically the surface layers of the polymer itself to improve its adhesion characteristics.

1.4 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.

1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Specific precautionary statements are given in 6.1.

Committee
D 14
DocumentType
Standard Practice
Pages
3
ProductNote
Reconfirmed 2003
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy
Supersedes

ASTM D 3164 : 2003 : R2017 Standard Test Method for Strength Properties of Adhesively Bonded Plastic Lap-Shear Sandwich Joints in Shear by Tension Loading
ASTM D 6465 : 1999 : R2016 Standard Guide for Selecting Aerospace and General Purpose Adhesives and Sealants
ASTM D 3163 : 2001 : R2014 Standard Test Method for Determining Strength of Adhesively Bonded Rigid Plastic Lap-Shear Joints in Shear by Tension Loading
ASTM D 3165 : 2007 : R2014 Standard Test Method for Strength Properties of Adhesives in Shear by Tension Loading of Single-Lap-Joint Laminated Assemblies
ASTM D 5041 : 1998 : R2019 Standard Test Method for Fracture Strength in Cleavage of Adhesives in Bonded Joints
ASTM D 2094 : 2000 : R2014 Standard Practice for Preparation of Bar and Rod Specimens for Adhesion Tests
ASTM D 5868 : 2001 : R2014 Standard Test Method for Lap Shear Adhesion for Fiber Reinforced Plastic (FRP) Bonding

ASTM D 952 : 2015 : REDLINE Standard Test Method for Bond or Cohesive Strength of Sheet Plastics and Electrical Insulating Materials
ASTM D 907 : 2015 : REDLINE Standard Terminology of Adhesives
ASTM D 905 : 2008 Standard Test Method for Strength Properties of Adhesive Bonds in Shear by Compression Loading

View more information
£55.10
Excluding VAT

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.