• There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

ASTM D 2369 : 2010

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Standard Test Method for Volatile Content of Coatings
Superseded date

11-11-2014

Published date

01-07-2010

CONTAINED IN VOL. 06.01, 2017 Specifies a procedure for the determination of the weight percent volatile content of solventborne and waterborne coatings.

1.1 This test method describes a procedure for the determination of the weight percent volatile content of solventborne and waterborne coatings. Test specimens are heated at 110 ± 5°C for 60 min.

Note 1—The coatings used in these round-robin studies represented air-dried, air-dried oxidizing, heat-cured baking systems, and also included multicomponent paint systems.

1.2 Sixty minutes at 110 ± 5°C is a general purpose test method based on the precision obtained with both solventborne and waterborne coatings (see Section 9).

1.3 This test method is viable for coatings wherein one or more parts may, at ambient conditions, contain liquid coreactants that are volatile until a chemical reaction has occurred with another component of the multi-package system.

Note 2—Committee D01 has run round-robin studies on volatiles of multicomponent paint systems. The only change in procedure is to premix the weighed components in the correct proportions and allow the specimens to stand at room temperature for 1 h prior to placing them into the oven.

Committee
D 01
DocumentType
Test Method
ProductNote
Reconfirmed 2010
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy
Supersedes

ASTM D 3794 : 2018 Standard Guide for Testing Coil Coatings
ASTM D 2832 : 1992 : R2016 Standard Guide for Determining Volatile and Nonvolatile Content of Paint and Related Coatings
ASTM D 7805 : 2013 Standard Terminology for Printing Ink Vehicles and Related Materials
ASTM D 5403 : 1993 : R2013 Standard Test Methods for Volatile Content of Radiation Curable Materials
ASTM F 940 : 1999 : R2013 Standard Practice for Quality Control Receipt Inspection Procedures for Protective Coatings (Paint), Used in Marine Construction and Shipbuilding
ASTM D 7232 : 2006 : R2016 Standard Test Method for Rapid Determination of the Nonvolatile Content of Coatings by Loss in Weight
ASTM D 6419 : 2000 : R2017 Standard Test Method for Volatile Content of Sheet-Fed and Coldset Web Offset Printing Inks
ASTM D 5327 : 1997 : R2013 Standard Practice for Evaluating and Comparing Transfer Efficiency of Spray Applied Coatings Under General Laboratory Conditions
ASTM D 4302 : 2014 Standard Specification for Artists’ Oil, Resin-Oil, and Alkyd Paints
ASTM D 5087 : 2002 : R2014 Standard Test Method for Determining Amount of Volatile Organic Compound (VOC) Released from Solventborne Automotive Coatings and Available for Removal in a VOC Control Device (Abatement)
ASTM D 4713 : 2012 Standard Test Methods for Nonvolatile Content of Heatset and Liquid Printing Ink Systems
ASTM D 2205 : 2015 Standard Guide for Selection of Tests for Traffic Paints
ASTM C 309 : 2011 Standard Specification for Liquid Membrane-Forming Compounds for Curing Concrete
ASTM C 461 : 2017 Standard Test Methods for Mastics and Coatings Used With Thermal Insulation
ASTM D 4764 : 2001 : R2016 Standard Test Method for Determination by X-ray Fluorescence Spectroscopy of Titanium Dioxide Content in Paint
ASTM D 6583 : 2013 : R2019 Standard Test Method for Porosity of Paint Film by Mineral Oil Absorption
ASTM D 5286 : 2001 : R2017 Standard Test Methods for Determination of Transfer Efficiency Under General Production Conditions for Spray Application of Paints
ASTM D 4209 : 2007 : R2019 Standard Practice for Determining Volatile and Nonvolatile Content of Cellulosics, Emulsions, Resin Solutions, Shellac, and Varnishes
ASTM D 3451 : 2006 : R2017 Standard Guide for Testing Coating Powders and Powder Coatings
ASTM D 6763 : 2016 Standard Guide for Testing Exterior Wood Stains and Clear Water Repellents
ASTM D 5325 : 2003 : R2014 Standard Test Method for Determination of Weight Percent Volatile Content of Water-Borne Aerosol Paints
ASTM C 156 : 2017 Standard Test Method for Water Loss [from a Mortar Specimen] Through Liquid Membrane-Forming Curing Compounds for Concrete
ASTM D 6266 : 2000 : REV A : R2017 Standard Test Method for Determining the Amount of Volatile Organic Compound (VOC) Released From Waterborne Automotive Coatings and Available for Removal in a VOC Control Device (Abatement)
ASTM C 1315 : 2011 Standard Specification for Liquid Membrane-Forming Compounds Having Special Properties for Curing and Sealing Concrete
ASTM D 4143 : 2016 Standard Guide for Testing Latex Vehicles
ASTM D 3105 : 2017 Standard Index of Methods for Testing Elastomeric and Plastomeric Roofing and Waterproofing Materials
ASTM D 5201 : 2005 : REV A : R2014 Standard Practice for Calculating Formulation Physical Constants of Paints and Coatings
ASTM D 6886 : 2018 Standard Test Method for Determination of the Weight Percent Individual Volatile Organic Compounds in Waterborne Air-Dry Coatings by Gas Chromatography
ASTM D 5009 : 2002 : R2017 Standard Test Method for Evaluating and Comparing Transfer Efficiency of Spray Applied Coatings Under Laboratory Conditions
ASTM D 2698 : 2005 : R2015 Standard Test Method for Determination of the Pigment Content of Solvent-Reducible Paints by High-Speed Centrifuging
ASTM D 3960 : 2005 : R2018 Standard Practice for Determining Volatile Organic Compound (VOC) Content of Paints and Related Coatings
ASTM D 7270 : 2007 : R2013 Standard Guide for Environmental and Performance Verification of Factory-Applied Liquid Coatings
ASTM D 5324 : 2016 Standard Guide for Testing Water-Borne Architectural Coatings
ASTM D 6093 : 1997 : R2016 Standard Test Method for Percent Volume Nonvolatile Matter in Clear or Pigmented Coatings Using a Helium Gas Pycnometer
ASTM D 3730 : 2017 Standard Guide for Testing High-Performance Interior Architectural Wall Coatings
ASTM D 5066 : 1991 : R2017 Standard Test Method for Determination of the Transfer Efficiency Under Production Conditions for Spray Application of Automotive Paints—Weight Basis
ASTM D 2697 : 2003 : R2014 Standard Test Method for Volume Nonvolatile Matter in Clear or Pigmented Coatings
ASTM D 6577 : 2015 Standard Guide for Testing Industrial Protective Coatings

ASTM E 177 : 2014 : REDLINE Standard Practice for Use of the Terms Precision and Bias in ASTM Test Methods
ASTM E 180 : 2003 Standard Practice for Determining the Precision of ASTM Methods for Analysis and Testing of Industrial and Specialty Chemicals (Withdrawn 2009)

View more information
Sorry this product is not available in your region.

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.