• There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

ASTM D 2486 : 2017 : REDLINE

Current
Current

The latest, up-to-date edition.

Standard Test Methods for Scrub Resistance of Wall Paints
Available format(s)

PDF

Language(s)

English

Published date

01-06-2017

CONTAINED IN VOL. 06.02, 2017 Defines a procedure for determining the resistance of wall paints to erosion caused by scrubbing, referred to herein after as 'scrub resistance.'

1.1These test methods cover a procedure for determining the resistance of wall paints to erosion caused by scrubbing, referred to herein after as “scrub resistance.”

1.2Two test methods are covered as follows:

1.2.1Test Method A—Cycles-to-failure obtained on test paint.

1.2.2Test Method B—Ratio expressed as a percentage of cycles-to-failure obtained on the test paint to that obtained on a concurrent run with a known reference paint.

1.3The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.

1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

1.5This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Committee
D 01
DocumentType
Redline
Pages
5
PublisherName
American Society for Testing and Materials
Status
Current

TT-P-1952 Revision F:2015 PAINT, TRAFFIC AND AIRFIELD MARKING, WATERBORNE
A-A-3126 Base Document:1972 COATING SYSTEM: TILE-LIKE HIGH PERFORMANCE ARCHITECTURAL
MIL A 3316 : C ADHESIVE, FIRE RESISTANT, THERMAL INSULATION
ASTM D 3089 : 1997 : R2008 Standard Practice for Determining the A-D Dimension of Aerosol Valve Dip Tubes
ASTM D 6736 : 2008 Standard Test Method for Burnish Resistance of Latex Paints
ASTM D 6900 : 2010 Standard Test Method for Wet Adhesion of Latex Paints to a Gloss Alkyd Enamel Substrate
ASTM E 1797 : 2012 Standard Specification for Reinforced Liquid Coating Encapsulation Products for Leaded Paint in Buildings
TT-P-29 Revision K:1991 PAINT, LATEX
CGSB-1.60 : 1997 INTERIOR ALKYD GLOSS ENAMEL
TT-P-001957 Base Document:1984 PAINT, LATEX (BACTERIOSTATIC AND FUNGISTATIC)
ASTM D 3730 : 2017 : REDLINE Standard Guide for Testing High-Performance Interior Architectural Wall Coatings
TT-P-1510 Revision A:1975 PAINT, LATEX, EXTERIOR, FOR WOOD SURFACES, WHITE AND TINTS
TT-P-650 Revision D:1988 PRIMER COATING, LATEX BASE, INTERIOR, WHITE (FOR GYPSUM WALLBOARD, OR PLASTER)
ASTM D 3927 : 1987 Guide for State and Institutional Purchasing of Paint (Withdrawn 1991)
STANAG 2836 : 0 REMOVABLE PAINTS FOR CAMOUFLAGE
CGSB 1.216 : 1997 EXTERIOR WATER-BORNE GLOSS ENAMEL
ASTM C 744 : 2016 : REDLINE Standard Specification for Prefaced Concrete and Calcium Silicate Masonry Units
TT-P-002119 Base Document:1980 PAINT, LATEX BASE, HIGH TRAFFIC AREA, FLAT AND EGGSHELL FINISH (LOW LUSTRE), (FOR INTERIOR USE)
CGSB-1.211 : 95 AMD 1 99 COATING SYSTEMS FOR MARINE FLOATING NAVIGATIONAL AIDS (BUOYS)
ASTM D 5324 : 2016 : REDLINE Standard Guide for Testing Water-Borne Architectural Coatings
ASTM D 6763 : 2016 : REDLINE Standard Guide for Testing Exterior Wood Stains and Clear Water Repellents
ASTM D 3323 : 1980 : R1988 : EDT 1 Guide for Testing Interior Solvent-Thinned Flat Wall Paints (Withdrawn 1993)
ASTM D 4213 : 2008 Standard Test Method for Scrub Resistance of Paints by Abrasion Weight Loss
ASTM D 4213 : 2008 : R2012 Standard Test Method for Scrub Resistance of Paints by Abrasion Weight Loss
ASTM F 793/F793M : 2015 : REDLINE Standard Classification of Wall Coverings by Use Characteristics
A-A-3185 Base Document:2001 PAINT, LATEX (CONTAINING POST-CONSUMER MATERIAL)
TT P 001952 : C PAINT, TRAFFIC AND AIRFIELD MARKING, WATERBORNE
A-A-3058 Base Document:1996 PAINT, INTERIOR, FIRE RETARDANT
CGSB 1.138 : 1997 EXTERIOR LATEX FLAT PAINT
ASTM E 1795 : 2017 : REDLINE Standard Specification for Non-Reinforced Liquid Coating Encapsulation Products for Leaded Paint in Buildings
ASTM E 1797 : 2012 : R2017 : EDT 1 Standard Specification for Reinforced Liquid Coating Encapsulation Products for Leaded Paint in Buildings
CGSB-1.208 : 1999 MARINE INTERIOR WATER-BORNE GLOSS ENAMEL
ASTM E 2136 : 2004 : R2013 Standard Guide for Specifying and Evaluating Performance of Single Family Attached and Detached Dwellings—Durability (Withdrawn 2022)
ASTM E 2136 : 2004 Standard Guide for Specifying and Evaluating Performance of Single Family Attached and Detached Dwellings-Durability
TT-C-001951 Base Document:1976 COATING, CLEAR (SATIN FINISH), POLYURETHANE, LATEX, FOR INTERIOR USE
CGSB-1.73 : 1997 EXTERIOR AND INTERIOR ENAMEL FOR FLOORS
ASTM D 6736 : 2008 : R2013 Standard Test Method for Burnish Resistance of Latex Paints
ASTM D 6900 : 2010 : R2015 Standard Test Method for Wet Adhesion of Latex Paints to a Gloss Alkyd Enamel Substrate

View more information
£55.10
Excluding VAT

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.