Name: ASTM D 2513 : 2007 : REV B
Brand: ASTM
Price: 90.16 GBP

ASTM D 2513 : 2007 : REV B

Superseded

View Superseded by

Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings

Available format(s)

Hardcopy , PDF

Superseded date

11-11-2014

Language(s)

English

Published date

15-11-2007

Publisher

American Society for Testing and Materials

1.1 This specification covers requirements and test methods for material (see Appendix X1 ) dimensions and tolerances, hydrostatic burst strength, chemical resistance, and impact resistance of plastic pipe, tubing, and fittings for use in fuel gas mains and services for direct burial and reliner applications. The annexes provide specific requirements and test methods for each of the materials currently approved. If and when additional materials are available, specific annex requirements will be added. The pipe and fittings covered by this specification are intended for use in the distribution of natural gas. Requirements for the qualifying of polyethylene systems for use with liquefied petroleum gas are covered in Annex A1 .

1.1.1 This specification does not cover threaded pipe. Design considerations are discussed in Appendix X2 . In-plant quality control programs are specified in Annex A3 and Annex A4 .

1.2 The text of this specification references notes, footnotes, and appendixes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification.

1.3 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are provided for information purposes only.

1.4 The following is an index of the annexes and appendixes in this specification:

Annex	Subject
	Polyethylene (PE) Pipe and Fittings
	Poly (Vinyl Chloride) (PVC) Pipe and Fittings for Maintenance or Repair
	In-Plant Quality Control for all materials up to 12 in.
	In-Plant Quality Control for PE materials between 14 and 24 in.
	Polyamide (PA) Pipe and Fittings
	Magnetic-detectable Polyethylene Pipe
	Crosslinked Polyethylene (PEX) Pipe
	Peelable PE Pipe

Appendixes	Subject
	New Materials
	Design Consideration
	Gas Pressure Pipe and Fittings Produced from Polyethylene (PE) materials with Minimum Required Strength (MRS) Designation

1.5 The following precautionary caveat pertains only to the test method portion, Section 6, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

^REFERENCE: ^ASTMGRP: ASTM Standards: 2.1.1 Terminology:2.1.2Test Methods for:2.1.3Practices for:^REFDOCID: D1898^REFDOCTITLE: Sampling of Plastics 2.1.4Specification for:^REFDOCID: D2740^REFDOCTITLE: Specification for Polyvinyl Chloride (PVC) Plastic Tubing^REFGRP: ANSI Standards:^REFDOCID: B16.40^REFDOCTITLE: Manually Operated Thermoplastic Gas Shutoffs and Valves in Gas Distribution Systems^REFDOCID: B31.8^REFDOCTITLE: Gas Transmission and Distribution Piping Systems^REFGRP: Federal Specifications:^REFDOCID: Fed. Std. No. 123^REFDOCTITLE: Marking for Shipment (Civil Agencies)^REFDOCID: OPS 49 CFR Part 192^REFDOCTITLE: Title 49, Code of Federal Regulations^REFGRP: Military Standards:^REFDOCID: MIL-STD-129^REFDOCTITLE: Marking for Shipment and Storage^REFDOCID: MIL-STD-1235^REFDOCTITLE: (ORD) Single- and Multi-Level Continuous Sampling Procedures and Tables for Inspection by Attributes^REFGRP: ISO Standards:^REFDOCID: ISO 4437^REFDOCTITLE: Buried polyethylene (PE) pipes for the supply of gaseous fuels-Metric series-Specifications^REFDOCID: ISO 11922-1^REFDOCTITLE: Thermoplastics pipes for the conveyance of fluids-Dimensions and tolerances -Part 1: Metric series^REFDOCID: ISO 17454^REFDOCTITLE: Plastics piping systems - multilayer pipe - test method for the adhesion of the different layers using a pulling rig.^REFDOCID: ISO 9080^REFDOCTITLE: Thermoplastics Pipes for the Transport of Fluids-Methods of Extrapolation of Hydrostatic Stress Rupture Data to Determine Long-Term Hydrostatic Strength of Thermoplastic Pipe Materials^REFDOCID: ISO 12162^REFDOCTITLE: Thermoplastic Materials for Pipes and Fittings for Pressure Applications-Classification and Designation-Overall Service (Design) Coefficient^REFGRP: Plastic Pipe Institute^REFDOCID: PPI TR-33^REFDOCTITLE: Generic Butt Fusion Joining for Polyethylene Gas Pipe^REFDOCID: PPI TR3^REFDOCTITLE: Policies and Procedures for Developing Hydrostatic Design Basis (HDB), Pressure Design Basis (PDB)^REFDOCID: PPI TR4^REFDOCTITLE: Hydrostatic Design Bases and Maximum Recommended Hydrostatic Design Stresses for Thermoplastic Piping Materials^REFDOCID: PPI TR-41,^REFDOCTITLE: Generic Saddle Fusion Joining Procedure for Polyethylene Gas Piping^REFDOCID: PPI TN-30/2006^REFDOCTITLE: Requirements for the Use of Rework Materials in Polyethylene Gas Pipe^REFDOCID: PPI TN-7^REFDOCTITLE: Nature of Hydrostatic Stress Rupture Curves^REFGRP: Other Documents:^REFDOCID: National Fire Protection Association: NFPA 58,^REFDOCTITLE: Storage and Handling Liquefied Petroleum Gases ^KEYWORDS: ^INDEX TERMS: ^STATUS: Dn Cn Sn Nn Mn ^APPROVAL: 20071115 ^PAGES: 27 ^COMMITTEE: F17 ^SUBCOMMITTEE: 6000 ^BOS: 08.04 ^ORGINFO: ANSI DOD ^ACTION: STD_REVISION ^MISCPUB: ^PDESIG: D2513 ^PYEAR: 2007B ^CLASS: Specification

Committee	F 17
DocumentType	Standard
Pages	27
PublisherName	American Society for Testing and Materials
Status	Superseded
SupersededBy	ASTM D 2513 : 2007 : REV B : EDT 1
Supersedes	ASTM D 2513 : 2007 : REV A

ASTM F 1563 : 2001 : R2011	Standard Specification for Tools to Squeeze-off Polyethylene (PE) Gas Pipe or Tubing
ASTM F 2897 : 2015 : REV A	Standard Specification for Tracking and Traceability Encoding System of Natural Gas Distribution Components (Pipe, Tubing, Fittings, Valves, and Appurtenances)
ASTM F 905 : 2004 : R2018	Standard Practice for Qualification of Polyethylene Saddle-Fused Joints
ASTM F 1041 : 2002 : R2016	Standard Guide for Squeeze-Off of Polyolefin Gas Pressure Pipe and Tubing
ASTM F 2830 : 2011 : R2017	Standard Specification for Manufacture and Joining of Polyethylene (PE) Gas Pressure Pipe With a Peelable Polypropylene (PP) Outer Layer
ASTM F 1804 : 2008 : R2016	Standard Practice for Determining Allowable Tensile Load for Polyethylene (PE) Gas Pipe During Pull-In Installation
ASTM F 1055 : 2016 : REV A	Standard Specification for Electrofusion Type Polyethylene Fittings for Outside Diameter Controlled Polyethylene and Crosslinked Polyethylene (PEX) Pipe and Tubing
ASTM F 1962 : 2011	Standard Guide for Use of Maxi-Horizontal Directional Drilling for Placement of Polyethylene Pipe or Conduit Under Obstacles, Including River Crossings (Withdrawn 2020)
ASTM F 2818 : 2010 : R2014 : EDT 1	Standard Specification for Specification for Crosslinked Polyethylene (PEX) Material Gas Pressure Pipe and Tubing
ASTM F 1924 : 2012	Standard Specification for Plastic Mechanical Fittings for Use on Outside Diameter Controlled Polyethylene Gas Distribution Pipe and Tubing
ASTM F 2880 : 2014	Standard Specification for Lap-Joint Type Flange Adapters for Polyethylene Pressure Pipe in Nominal Pipe Sizes <fraction><num>3/4</den></fraction > in. to 65 in.
ASTM F 1734 : 2019	Standard Practice for Qualification of a Combination of Squeeze Tool, Pipe, and Squeeze-Off Procedures to Avoid Long-Term Damage in Polyethylene (PE) Gas Pipe
ASTM D 2683 : 2014	Standard Specification for Socket-Type Polyethylene Fittings for Outside Diameter-Controlled Polyethylene Pipe and Tubing
ASTM F 1056 : 2018	Standard Specification for Socket Fusion Tools for Use in Socket Fusion Joining Polyethylene Pipe or Tubing and Fittings
ASTM F 2634 : 2015	Standard Test Method for Laboratory Testing of Polyethylene (PE) Butt Fusion Joints using Tensile-Impact Method
ASTM F 2620 : 2019	Standard Practice for Heat Fusion Joining of Polyethylene Pipe and Fittings
ASTM F 2619/F2619M : 2013	Standard Specification for High-Density Polyethylene (PE) Line Pipe
ASTM F 2896 : 2011 : R2017	Standard Specification for Reinforced Polyethylene Composite Pipe For The Transport Of Oil And Gas And Hazardous Liquids
ASTM F 1588 : 1996 : R2015	Standard Test Method for Constant Tensile Load Joint Test (CTLJT)
ASTM F 412 : 2019	Standard Terminology Relating to Plastic Piping Systems
ASTM D 3261 : 2016	Standard Specification for Butt Heat Fusion Polyethylene (PE) Plastic Fittings for Polyethylene (PE) Plastic Pipe and Tubing