• There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

ASTM D 3120 : 2008 : R2014

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Standard Test Method for Trace Quantities of Sulfur in Light Liquid Petroleum Hydrocarbons by Oxidative Microcoulometry
Available format(s)

Hardcopy , PDF

Superseded date

25-06-2019

Language(s)

English

Published date

01-05-2014

This test method covers the determination of sulfur concentration in the range from 3.0 to 1000 mg/kg in light liquid hydrocarbons and fuels with oxygenates boiling in the range from 26 to 274°C (80 to 525°F).

1.1This test method covers the determination of sulfur concentration in the range from 3.0 to 1000 mg/kg in light liquid hydrocarbons and fuels with oxygenates boiling in the range from 26 to 274°C (80 to 525°F).

Note 1:Preliminary data has shown that this test method is also applicable to the determination of sulfur in denatured fuel ethanol (Specification D4806), automotive spark ignition engine fuel (Specification D4814), Ed75–Ed85 (Specification D5798) or gasoline-oxygenate fuel blends with greater than 10% ethanol. However, the precision for these materials has not been determined. Subcommittee D02.03 is undertaking activities to obtain precision statements for these materials.

1.2Other materials falling within the distillation range specified in 1.1, but having sulfur concentrations above 1000 mg/kg, may be tested using appropriate dilutions to bring them within the specified limit. In addition, sample types that may be outside the specified distillation range, such as diesels and biodiesels, may be analyzed by this test method.

1.3The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. The preferred units are milligrams per kilogram (mg/kg).

1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.For specific hazard statements, see Sections 7 – 9.

Committee
D 02
DocumentType
Test Method
Pages
10
ProductNote
Reconfirmed 2014
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy
Supersedes

ASTM D 1655 : 2019 Standard Specification for Aviation Turbine Fuels
ASTM D 3338/D3338M : 2009 : R2014 : EDT 2 Standard Test Method for Estimation of Net Heat of Combustion of Aviation Fuels
ASTM D 7862 : 2019 Standard Specification for Butanol for Blending with Gasoline for Use as Automotive Spark-Ignition Engine Fuel
ASTM D 6074 : 2015 Standard Guide for Characterizing Hydrocarbon Lubricant Base Oils
ASTM D 4806 : 2019 Standard Specification for Denatured Fuel Ethanol for Blending with Gasolines for Use as Automotive Spark-Ignition Engine Fuel
ASTM D 6227 : 2018 Standard Specification for Unleaded Aviation Gasoline Containing a Non-hydrocarbon Component
ASTM D 6751 : 2019 Standard Specification for Biodiesel Fuel Blend Stock (B100) for Middle Distillate Fuels
ASTM D 5623 : 2019 Standard Test Method for Sulfur Compounds in Light Petroleum Liquids by Gas Chromatography and Sulfur Selective Detection
ASTM D 7455 : 2019 Standard Practice for Sample Preparation of Petroleum and Lubricant Products for Elemental Analysis
ASTM D 4809 : 2018 Standard Test Method for Heat of Combustion of Liquid Hydrocarbon Fuels by Bomb Calorimeter (Precision Method)
ASTM D 7807 : 2012 Standard Test Method for Determination of Boiling Range Distribution of Hydrocarbon and Sulfur Components of Petroleum Distillates by Gas Chromatography and Chemiluminescence Detection
ASTM D 7578 : 2018 Standard Guide for Calibration Requirements for Elemental Analysis of Petroleum Products and Lubricants
ASTM D 4529 : 2017 Standard Test Method for Estimation of Net Heat of Combustion of Aviation Fuels
ASTM D 1836 : 2007 : R2013 Standard Specification for Commercial Hexanes
ASTM D 3246 : 2015 Standard Test Method for Sulfur in Petroleum Gas by Oxidative Microcoulometry (Withdrawn 2024)
ASTM D 4814 : 2019 Standard Specification for Automotive Spark-Ignition Engine Fuel
ASTM D 8076 : 2018 Standard Specification for 100 Research Octane Number Test Fuel for Automotive Spark-Ignition Engines
ASTM D 7155 : 2018 Standard Practice for Evaluating Compatibility of Mixtures of Turbine Lubricating Oils
ASTM D 8147 : 2017 Standard Specification for Special-Purpose Test Fuels for Aviation Compression-Ignition Engines
ASTM D 1405/D1405M : 2008 : R2013 Standard Test Method for Estimation of Net Heat of Combustion of Aviation Fuels (Withdrawn 2019)
ASTM D 7467 : 2019 Standard Specification for Diesel Fuel Oil, Biodiesel Blend (B6 to B20)
ASTM D 240 : 2017 Standard Test Method for Heat of Combustion of Liquid Hydrocarbon Fuels by Bomb Calorimeter

CFR 29(PT1910.1000 TO END) : 0 LABOR - OCCUPATIONAL SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR

View more information
£62.61
Excluding VAT

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.