• There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

ASTM D 3288/D3288M : 2020

Current
Current

The latest, up-to-date edition.

Standard Test Methods for Magnet-Wire Enamels
Available format(s)

Hardcopy , PDF

Language(s)

English

Published date

01-09-2020

1.1These test methods cover testing liquid enamel coatings used to produce film-insulated magnet wire.

1.2The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined

1.3The test methods appear as follows:

Sections

Density

6 – 10

Determined Solids

16 – 22

Effective Solids

31 – 37

Flash Point

11 – 15

Infrared Analysis

45 – 50

Stack Loss

23 – 30

Viscosity

38 – 44

1.4There is no known IEC equivalent document.

1.5This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.6This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Committee
D 09
DocumentType
Test Method
Pages
7
PublisherName
American Society for Testing and Materials
Status
Current
Supersedes

ASTM D 476 : 2015 : R2021 Standard Classification for Dry Pigmentary Titanium Dioxide Products
ASTM E 131 : 2010 : R2023 Standard Terminology Relating to Molecular Spectroscopy
ASTM D 5423 : 2022 Standard Specification for Forced-Convection Laboratory Ovens for Evaluation of Electrical Insulation
ASTM D 1298 : 2012 : REV B : R2017 : EDT 1 Standard Test Method for Density, Relative Density, or API Gravity of Crude Petroleum and Liquid Petroleum Products by Hydrometer Method
ASTM E 168 : 2016 : R2023 Standard Practices for General Techniques of Infrared Quantitative Analysis
ASTM D 1298 : 2012 : REV B : R2017 Standard Test Method for Density, Relative Density, or API Gravity of Crude Petroleum and Liquid Petroleum Products by Hydrometer Method
ASTM D 1711 : 2011 Standard Terminology Relating to Electrical Insulation
ASTM E 691 : 2020 Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method
ASTM E 691 : 2019 : EDT 1 Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method
ASTM E 691 : 2023 Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method
ASTM D 5423 : 2023 Standard Specification for Forced-Convection Laboratory Ovens for Evaluation of Electrical Insulation
ASTM D 56 : 2021 : REV A Standard Test Method for Flash Point by Tag Closed Cup Tester
ASTM E 131 : 2010 : R2015 Standard Terminology Relating to Molecular Spectroscopy
ASTM E 691 : 2022 Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method
ASTM D 56 : 2016 : REV A Standard Test Method for Flash Point by Tag Closed Cup Tester
ASTM E 691 : 2009 Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method
ASTM E 2975 : 2023 Standard Test Method for Calibration or Calibration Verification of Concentric Cylinder Rotational Viscometers
ASTM D 56 : 2021 Standard Test Method for Flash Point by Tag Closed Cup Tester
ASTM E 691 : 2021 Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method
ASTM D 1711 : 2024 Standard Terminology Relating to Electrical Insulation
ASTM D 476 : 2015 Standard Classification for Dry Pigmentary Titanium Dioxide Products
ASTM D 1711 : 2022 Standard Terminology Relating to Electrical Insulation
ASTM D 1711 : 2020 Standard Terminology Relating to Electrical Insulation
ASTM D 56 : 2022 Standard Test Method for Flash Point by Tag Closed Cup Tester
ASTM D 56 : 1987 Standard Test Method for Flash Point by Tag Closed Tester
ASTM D 5423 : 2014 Standard Specification for Forced-Convection Laboratory Ovens for Evaluation of Electrical Insulation
ASTM E 2975 : 2016 : EDT 1 Standard Test Method for Calibration or Calibration Verification of Concentric Cylinder Rotational Viscometers
ASTM E 168 : 2016 Standard Practices for General Techniques of Infrared Quantitative Analysis

View more information
£52.59
Excluding VAT

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.