Name: ASTM D 333 : 2001 : R2021
Brand: ASTM
Price: 52.59 GBP

Standard Guide for Clear and Pigmented Lacquers

Available format(s)

Hardcopy , PDF

Language(s)

English

Published date

16-06-2021

Publisher

American Society for Testing and Materials

1.1These test methods cover procedures for testing lacquers and lacquer coatings. The test methods included are listed in Table 1.

Note 1:In accordance with Terminology D16, a lacquer is defined as a coating composition that is based on synthetic thermoplastic film-forming material dissolved in organic solvent(s) and that dries primarily by solvent evaporation. Typical lacquers include those based on nitrocellulose, other cellulose derivatives, vinyl resins, acrylic resins, etc.

Note 2:Lacquers may be applied under such diverse conditions, to so many different surfaces, and their dried films may be subjected to so many kinds of wear and exposure that it is not possible to assure desired performance from a single selection of test methods and numerical results therefrom. Those skilled in lacquer technology may find partial assurance of obtaining desired qualities in various types of lacquers through careful selection of the methods covered herein and intelligent interpretation of results therefrom.

Note 3:It is intended ultimately to remove all experimental procedures from Test Methods D333 and to establish them as a guide to the selection of test methods for lacquer and perhaps to interpretation of results therefrom. Temporarily there remain in Test Methods D333 a few tests that are too short or otherwise presently unsuitable for establishment under separate ASTM designations.

1.2The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.

1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.4This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Committee	D 01
DocumentType	Guide
Pages	6
PublisherName	American Society for Testing and Materials
Status	Current
Supersedes	ASTM D 333 : 2001 : R2013

ASTM D 2832 : 1992 : R2016	Standard Guide for Determining Volatile and Nonvolatile Content of Paint and Related Coatings
ASTM D 365 : 2001 : R2017	Standard Guide for Soluble Nitrocellulose Base Solutions
ASTM D 3023 : 1998 : R2017	Standard Practice for Determination of Resistance of Factory-Applied Coatings on Wood Products to Stains and Reagents

ASTM D 3278 : 2020	Standard Test Methods for Flash Point of Liquids by Small Scale Closed-Cup Apparatus
ASTM D 2204 : 1965 : R1975	Method of Test for Perspiration Resistance of Organic Coatings
ASTM D 2244 : 2021	Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates
ASTM D 2091 : 1996 : R2024	Standard Test Method for Print Resistance of Lacquers
ASTM D 1735 : 2021	Standard Practice for Testing Water Resistance of Coatings Using Water Fog Apparatus
ASTM D 2244 : 2023	Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates
ASTM D 609 : 2017 : R2022	Standard Practice for Preparation of Cold-Rolled Steel Panels for Testing Paint, Varnish, Conversion Coatings, and Related Coating Products
ASTM D 1729 : 2016	Standard Practice for Visual Appraisal of Colors and Color Differences of Diffusely-Illuminated Opaque Materials
ASTM D 1200 : 2023	Standard Test Method for Viscosity by Ford Viscosity Cup
ASTM D 2805 : 2011 : R2018	Standard Test Method for Hiding Power of Paints by Reflectometry
ASTM D 1200 : 2010 : R2018	Standard Test Method for Viscosity by Ford Viscosity Cup
ASTM D 2199 : 2003 : R2013	Standard Test Method for Measurement of Plasticizer Migration From Vinyl Fabrics to Lacquers
ASTM D 445 : 2021 : EDT 2	Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity)
ASTM D 93 : 2019	Standard Test Methods for Flash Point by Pensky-Martens Closed Cup Tester
ASTM D 2244 : 2016	Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates
ASTM D 445 : 2017 : REV A	Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity)
ASTM D 1544 : 2004 : R2018	Standard Test Method for Color of Transparent Liquids (Gardner Color Scale)
ASTM D 16 : 2019	Standard Terminology for Paint, Related Coatings, Materials, and Applications
ASTM D 3278 : 2021	Standard Test Methods for Flash Point of Liquids by Small Scale Closed-Cup Apparatus
ASTM D 968 : 2022	Standard Test Methods for Abrasion Resistance of Organic Coatings by Falling Abrasive
ASTM D 1644 : 2001 : R2017	Standard Test Methods for Nonvolatile Content of Varnishes
ASTM D 1210 : 2005 : R2022	Standard Test Method for Fineness of Dispersion of Pigment-Vehicle Systems by Hegman-Type Gage
ASTM D 1735 : 2014	Standard Practice for Testing Water Resistance of Coatings Using Water Fog Apparatus
ASTM D 56 : 2021 : REV A	Standard Test Method for Flash Point by Tag Closed Cup Tester
ASTM D 2199 : 2003 : R2021	Standard Test Method for Measurement of Plasticizer Migration From Vinyl Fabrics to Lacquers
ASTM D 1210 : 2005 : R2014	Standard Test Method for Fineness of Dispersion of Pigment-Vehicle Systems by Hegman-Type Gage
ASTM D 1535 : 2014 : R2018	Standard Practice for Specifying Color by the Munsell System
ASTM D 1644 : 2001 : R2023	Standard Test Methods for Nonvolatile Content of Varnishes
ASTM D 56 : 2016 : REV A	Standard Test Method for Flash Point by Tag Closed Cup Tester
ASTM D 445 : 2019 : REV A	Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity)
ASTM D 16 : 2024	Standard Terminology for Paint, Related Coatings, Materials, and Applications
ASTM B 117 : 2019	Standard Practice for Operating Salt Spray (Fog) Apparatus
ASTM D 1544 : 2004 : R2023	Standard Test Method for Color of Transparent Liquids (Gardner Color Scale)
ASTM D 445 : 2019	Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity)
ASTM D 56 : 2021	Standard Test Method for Flash Point by Tag Closed Cup Tester
ASTM E 308 : 2018	Standard Practice for Computing the Colors of Objects by Using the CIE System
ASTM D 823 : 2018	Standard Practices for Producing Films of Uniform Thickness of Paint, Coatings and Related Products on Test Panels
ASTM D 2244 : 2022	Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates
ASTM D 445 : 2024	Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity)
ASTM D 445 : 2021	Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity)
ASTM D 1729 : 2022	Standard Practice for Visual Appraisal of Colors and Color Differences of Diffusely-Illuminated Opaque Materials
ASTM D 56 : 2022	Standard Test Method for Flash Point by Tag Closed Cup Tester
ASTM D 2805 : 2011 : R2023	Standard Test Method for Hiding Power of Paints by Reflectometry
ASTM D 445 : 2018	Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity)
ASTM E 308 : 2022	Standard Practice for Computing the Colors of Objects by Using the CIE System
ASTM D 609 : 2017	Standard Practice for Preparation of Cold-Rolled Steel Panels for Testing Paint, Varnish, Conversion Coatings, and Related Coating Products
ASTM D 1535 : 2014 : R2023	Standard Practice for Specifying Color by the Munsell System
ASTM D 968 : 2017	Standard Test Methods for Abrasion Resistance of Organic Coatings by Falling Abrasive
ASTM D 445 : 2021 : EDT 1	Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity)
ASTM D 659 : 1986 : EDT 1	Method of Evaluating Degree of Chalking of Exterior Paints
ASTM D 823 : 2018 : R2022	Standard Practices for Producing Films of Uniform Thickness of Paint, Coatings and Related Products on Test Panels
ASTM D 16 : 2023	Standard Terminology for Paint, Related Coatings, Materials, and Applications
ASTM D 445 : 2023	Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity)
ASTM D 93 : 2018	Standard Test Methods for Flash Point by Pensky-Martens Closed Cup Tester