• There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

ASTM D 3462/D3462M : 2019

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Standard Specification for Asphalt Shingles Made from Glass Felt and Surfaced with Mineral Granules
Available format(s)

Hardcopy , PDF

Superseded date

09-06-2023

Language(s)

English

Published date

12-03-2019

This specification covers asphalt roofing in shingle form, composed of glass felt or felts impregnated and coated on both sides with asphalt, and surfaced on the weather side with mineral granules.

1.1This specification covers asphalt roofing in shingle form, composed of glass felt or felts impregnated and coated on both sides with asphalt, and surfaced on the weather side with mineral granules. This specification is designed for the evaluation of products as manufactured. The test methods, physical requirements, and minimum masses are to be measured immediately after packaging or at a reasonable time, as agreed upon between buyer and seller, after manufacture and before installation. Physical and performance requirements after application and during in-service use of the products described herein are beyond the scope of this material specification.

1.2Shingles meeting this specification are intended to be applied with a headlap of not less than 51 mm [2 in.].

1.3The shingles shall be supplied with a factory-applied self-sealing adhesive or be designed to be locked together during installation of the shingles.

1.4The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

1.5The following safety hazards caveat pertains only to the test method described in this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.6This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Committee
D 08
DocumentType
Standard
Pages
4
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy
Supersedes

ASTM D 7158/D7158M : 2020 Standard Test Method for Wind Resistance of Asphalt Shingles (Uplift Force/Uplift Resistance Method)
ASTM D 6381/D6381M : 2015 : R2020 Standard Test Method for Measurement of Asphalt Shingle Mechanical Uplift Resistance
ASTM D 7349/D7349M : 2015(R2019) Standard Test Method for Determining the Capability of Roofing and Waterproofing Materials to Seal Around Fasteners

ASTM D 1079 : 2018 : EDT 1 Standard Terminology Relating to Roofing and Waterproofing
ASTM D 1079 : 2008 : REV A Standard Terminology Relating to Roofing and Waterproofing
ASTM D 1922 : 2008 Standard Test Method for Propagation Tear Resistance of Plastic Film and Thin Sheeting by Pendulum Method
ASTM F 1667 : 2005 Standard Specification for Driven Fasteners: Nails, Spikes, and Staples
ASTM D 1079 : 2016 Standard Terminology Relating to Roofing and Waterproofing
ASTM D 1079 : 2006 Terminology Relating to Roofing and Waterproofing
ASTM D 228/D228M : 2021 Standard Test Methods for Sampling, Testing, and Analysis of Asphalt Roll Roofing, Cap Sheets, and Shingles Used in Roofing and Waterproofing
ASTM F 1667 : 2018 Standard Specification for Driven Fasteners: Nails, Spikes, and Staples
ASTM D 1922 : 2015 Standard Test Method for Propagation Tear Resistance of Plastic Film and Thin Sheeting by Pendulum Method
ASTM D 1079 : 2020 Standard Terminology Relating to Roofing and Waterproofing
ASTM D 1922 : 2023 Standard Test Method for Propagation Tear Resistance of Plastic Film and Thin Sheeting by Pendulum Method
ASTM F 1667 : 2013 Standard Specification for Driven Fasteners: Nails, Spikes, and Staples
ASTM D 1922 : 2006 : REV A Standard Test Method for Propagation Tear Resistance of Plastic Film and Thin Sheeting by Pendulum Method
ASTM F 1667 : 2011 : REV A Standard Specification for Driven Fasteners: Nails, Spikes, and Staples
ASTM F 1667 : 2011 : REV A : EDT 1 Standard Specification for Driven Fasteners: Nails, Spikes, and Staples
ASTM F 1667 : 2015 Standard Specification for Driven Fasteners: Nails, Spikes, and Staples
ASTM F 1667 : 2021 Standard Specification for Driven Fasteners: Nails, Spikes, and Staples
ASTM F 1667 : 2010 Standard Specification for Driven Fasteners: Nails, Spikes, and Staples
ASTM F 1667 : 2018 : REV A Standard Specification for Driven Fasteners: Nails, Spikes, and Staples
ASTM D 1079 : 2013 Standard Terminology Relating to Roofing and Waterproofing
ASTM D 1079 : 2007 : REV A Terminology Relating to Roofing and Waterproofing
ASTM D 36/D36M : 2014 : EDT 1 Standard Test Method for Softening Point of Bitumen (Ring-and-Ball Apparatus)
ASTM D 1079 : 2010 Standard Terminology Relating to Roofing and Waterproofing
ASTM D 1922 : 2003 Standard Test Method for Propagation Tear Resistance of Plastic Film and Thin Sheeting by Pendulum Method
ASTM D 1079 : 2018 Standard Terminology Relating to Roofing and Waterproofing
ASTM F 1667 : 2000 Standard Specification for Driven Fasteners: Nails, Spikes, and Staples
ASTM F 1667 : 2003 Standard Specification for Driven Fasteners: Nails, Spikes, and Staples
ASTM F 1667 : 2020 Standard Specification for Driven Fasteners: Nails, Spikes, and Staples
ASTM F 1667 : 2001 : REV A Standard Specification for Driven Fasteners: Nails, Spikes, and Staples
ASTM D 1079 : 2005 : REV A Terminology Relating to Roofing and Waterproofing
ASTM F 1667 : 2011 Standard Specification for Driven Fasteners: Nails, Spikes, and Staples
ASTM D 1922 : 2015 : R2020 Standard Test Method for Propagation Tear Resistance of Plastic Film and Thin Sheeting by Pendulum Method
ASTM D 1079 : 2002 Standard Terminology Relating to Roofing, Waterproofing, and Bituminous Materials
ASTM F 1667 : 2002 : REV A Standard Specification for Driven Fasteners: Nails, Spikes, and Staples
ASTM D 1922 : 2003 : REV A Standard Test Method for Propagation Tear Resistance of Plastic Film and Thin Sheeting by Pendulum Method
ASTM D 1079 : 2001 Standard Terminology Relating to Roofing, Waterproofing, and Bituminous Materials
ASTM F 1667 : 2017 Standard Specification for Driven Fasteners: Nails, Spikes, and Staples
ASTM D 1922 : 2005 Standard Test Method for Propagation Tear Resistance of Plastic Film and Thin Sheeting by Pendulum Method
ASTM D 1079 : 2000 : REV A Standard Terminology Relating to Roofing, Waterproofing, and Bituminous Materials
ASTM D 1922 : 2000 : REV A Standard Test Method for Propagation Tear Resistance of Plastic Film and Thin Sheeting by Pendulum Method
ASTM F 1667 : 2002 Standard Specification for Driven Fasteners: Nails, Spikes, and Staples
ASTM D 1922 : 2006 Standard Test Method for Propagation Tear Resistance of Plastic Film and Thin Sheeting by Pendulum Method
ASTM D 1079 : 2013 : EDT 1 Standard Terminology Relating to Roofing and Waterproofing
ASTM D 1922 : 2009 Standard Test Method for Propagation Tear Resistance of Plastic Film and Thin Sheeting by Pendulum Method
ASTM D 1079 : 2009 Standard Terminology Relating to Roofing and Waterproofing

View more information
£55.10
Excluding VAT

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.