• There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

ASTM D 3588 : 1998 : R2003

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Standard Practice for Calculating Heat Value, Compressibility Factor, and Relative Density of Gaseous Fuels
Available format(s)

Hardcopy , PDF

Superseded date

11-11-2014

Language(s)

English

Published date

10-05-2003

CONTAINED IN VOL. 05.06, 2017 Defines procedures for calculating heating value, relative density, and compressibility factor at base conditions (14.696 psia and 60 degrees F (15.6 degrees C)) for natural gas mixtures from compositional analysis.

1.1 This practice covers procedures for calculating heating value, relative density, and compressibility factor at base conditions (14.696 psia and 60°F (15.6°C)) for natural gas mixtures from compositional analysis. It applies to all common types of utility gaseous fuels, for example, dry natural gas, reformed gas, oil gas (both high and low Btu), propane-air, carbureted water gas, coke oven gas, and retort coal gas, for which suitable methods of analysis as described in Section 6 are available. Calculation procedures for other base conditions are given.

1.2 The values stated in inch-pound units are to be regarded as the standard. The SI units given in parentheses are for information only.

1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Committee
D 03
DocumentType
Standard Practice
Pages
9
ProductNote
Reconfirmed 2003
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy
Supersedes

ASTM F 2144 : 2017 Standard Test Method for Performance of Large Open Vat Fryers
ASTM F 1695 : 2003 : R2015 Standard Test Method for Performance of Underfired Broilers
ASTM F 2239 : 2010 : R2016 Standard Test Method for Performance of Conveyor Broilers
ASTM F 2379 : 2004 : R2016 Standard Test Method for Energy Performance of Powered Open Warewashing Sinks
ASTM F 1275 : 2014 Standard Test Method for Performance of Griddles
ASTM F 2238 : 2016 Standard Test Method for Performance of Rapid Cook Ovens
ASTM F 1920 : 2015 Standard Test Method for Performance of Rack Conveyor Commercial Dishwashing Machines
ASTM D 7164 : 2010 : R2015 Standard Practice for On-line/At-line Heating Value Determination of Gaseous Fuels by Gas Chromatography
ASTM D 7551 : 2010 : R2015 Standard Test Method for Determination of Total Volatile Sulfur in Gaseous Hydrocarbons and Liquefied Petroleum Gases and Natural Gas by Ultraviolet Fluorescence
ASTM F 2022 : 2001 : R2019 Standard Test Method for Performance of Booster Heaters
ASTM D 7833 : 2014 Standard Test Method for Determination of Hydrocarbons and Non-Hydrocarbon Gases in Gaseous Mixtures by Gas Chromatography
ASTM D 7314 : 2010 : R2015 Standard Practice for Determination of the Heating Value of Gaseous Fuels using Calorimetry and On-line/At-line Sampling
ASTM F 2861 : 2017 Standard Test Method for Enhanced Performance of Combination Oven in Various Modes
ASTM F 3216 : 2016 Standard Test Method for Performance of Retherm Ovens
ASTM F 1361 : 2017 Standard Test Method for Performance of Open Deep Fat Fryers
ASTM F 1991 : 1999 : R2016 Standard Test Method for Performance of Chinese (Wok) Ranges
ASTM F 1496 : 2013 : R2019 Standard Test Method for Performance of Convection Ovens
ASTM F 2237 : 2003 : R2015 Standard Test Method for Performance of Upright Overfired Broilers
ASTM F 2473 : 2012 : R2018 Standard Test Method for Performance of Water-Bath Rethermalizers
ASTM F 1605 : 2014 : R2019 Standard Test Method for Performance of Double-Sided Griddles
ASTM F 2644 : 2007 : R2019 Standard Test Method for Performance of Commercial Patio Heaters
ASTM D 7940 : 2014 Standard Practice for Analysis of Liquefied Natural Gas (LNG) by Fiber-Coupled Raman Spectroscopy
ASTM F 1484 : 2018 Standard Test Methods for Performance of Steam Cookers
ASTM F 1696 : 2018 Standard Test Method for Energy Performance of Stationary-Rack, Door-Type Commercial Dishwashing Machines
ASTM F 3051 : 2014 : R2019 Standard Test Method for Performance of Cook-and-Hold Ovens

GPA 2166 : 2005(R2017) OBTAINING NATURAL GAS SAMPLES FOR ANALYSIS BY GAS CHROMATOGRAPHY
GPA 2261 : 2013 ANALYSIS FOR NATURAL GAS AND SIMILAR GASEOUS MIXTURES BY GAS CHROMATOGRAPHY
GPA 2145 : 2016 TABLE OF PHYSICAL PROPERTIES FOR HYDROCARBONS AND OTHER COMPOUNDS OF INTEREST TO NATURAL GAS AND NATURAL GAS LIQUIDS INDUSTRIES
ASTM D 1717 : 1961 : R1975 Method of Test for Analysis of Commercial Butane-Butiene Mixtures and Isolutylene by Gas Chromatography (Withdrawn 1982)
GPA 2172 : 2014 CALCULATION OF GROSS HEATING VALUE, RELATIVE DENSITY, COMPRESSIBILITY AND THEORETICAL HYDROCARBON LIQUID CONTENT FOR NATURAL GAS MIXTURES FOR CUSTODY TRANSFER
ASTM D 1945 : 2014 : REDLINE Standard Test Method for Analysis of Natural Gas by Gas Chromatography

View more information
£62.61
Excluding VAT

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.