• There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

ASTM D 4066 : 2013

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Standard Classification System for Nylon Injection and Extrusion Materials (PA)
Available format(s)

Hardcopy , PDF

Superseded date

12-11-2019

Language(s)

English

Published date

01-07-2013

CONTAINED IN VOL. 08.02, 2014 Specifies nylon materials suitable for injection molding and extrusion. Some compositions are also suitable for compression molding and application from solution.

1.1This classification system covers nylon materials suitable for injection molding and extrusion. Some of these compositions are also suitable for compression molding and application from solution.

1.2The properties included in this classification system are those required to identify the compositions covered. There may be other requirements necessary to identify particular characteristics important to specialized applications. These may be specified by using the suffixes as given in Section 5.

1.3This classification system and subsequent line call-out (specification) are intended to provide a means of calling out plastic materials used in the fabrication of end items or parts. It is not intended for the selection of materials. Material selection should be made by those having expertise in the plastic field after careful consideration of the design and the performance required of the part, the environment to which it will be exposed, the fabrication process to be employed, the costs involved, and the inherent properties of the material other than those covered by this classification system.

1.4The values stated in SI units are to be regarded as the standard.

1.5The following precautionary caveat pertains only to the test methods portion, Section 11, of this classification system. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Note 1There is no known ISO equivalent to this standard.
Note 2This classification system is being revised to include international 4-mm specimens and test procedures as the standard for compliance. The 3.2-mm specimens; test methods; and Tables PA, A, and B are included in Appendix X3 as a reference for those wishing to use them. It is recommended that the material manufacturer be consulted on all call-outs against this classification system.

Committee
D 20
DevelopmentNote
Supersedes ASTM D 2897. (03/2002) Supersedes MIL P 46180 (07/2004)
DocumentType
Standard
Pages
18
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy
Supersedes

MIL-N-85615-10 Base Document:1989 NUT, SELF-SEALING, SELF-LOCKING, CRES, 160 KSI FTU, 250 DEGREES F & 450 DEGREES F
MIL-DTL-39024-14 Revision C:2008 CONNECTORS, ELECTRICAL, TEST POINT TYPE, PANEL TYPE; SINGLE TEST POINT SUBMINIATURE (PUSH-IN), LOW VOLTAGE, .080
MIL-DTL-3661 Revision D:2013 Lampholders, Indicator Lights, Indicator Light Housings, and Indicator Light Lenses, General Specification for
ASTM D 6260 : 1998 Standard Test Method for Gravimetric Determination of Carbon Black in Nylon Materials (PA) (Withdrawn 2004)
MIL-B-41816 Revision H:1990 BOOTS, COLD WEATHER, INSULATED, RUBBER (WET-COLD; DRY-EXTREME COLD)
MIL-M-38527 Revision D:1992 MOUNTING PADS, ELECTRICAL-ELECTRONIC COMPONENT, GENERAL SPECIFICATION FOR
MIL-T-45309 Revision E:1983 TANK, COMBAT, FULL TRACKED, 105 MM GUN, M60, M60A1, M601A (RISE) & M60A3 PROCESSING FOR SHIPMENT & STORAGE OF
MIL C 27500 : G CABLE, POWER, ELECTRICAL & CABLE SPECIAL PURPOSE, ELECTRICAL SHIELDED & UNSHIELDED
MIL-DTL-39024-15 Revision C:2008 CONNECTORS, ELECTRICAL, TEST POINT TYPE, PRINTED WIRING TYPE; SINGLE TEST POINT, LOW VOLTAGE, .080
A-A-55469 Revision B:2015 CONNECTORS, ELECTRICAL, PLUGS, TIP (TEST POINT PLUG, BANANA PLUG) GENERAL REQUIREMENTS FOR
MIL B 81757 : C BATTERIES & CELLS STORAGE, NICKEL CADMIUM, AIRCRAFT GENERAL SPECIFICATION FOR
MIL-N-25027-1 Revision A:1995 NUT, SELF-LOCKING, HEAVY HEX, (NON-METALLIC INSERT) 250 & 450 DEG F, UNJC-3B, 1/4 THROUGH 2-1/2 INCH NOMINAL DIAMETERS, NICKEL-COPPER ALLOY
MIL-DTL-39024-13 Revision D:2011 CONNECTORS, ELECTRICAL, TEST POINT TYPE, PRINTED WIRING TYPE; SINGLE TEST POINT (RIGHT ANGLE, 2-LEG MOUNTING), LOW VOLTAGE, .080
MIL-DTL-642 Revision F:2015 PLUGS, TELEPHONE, AND ACCESSORY SCREWS, GENERAL SPECIFICATION FOR
CSA Z662.1 : 2013 COMMENTARY ON CSA Z662-07, OIL AND GAS PIPELINE SYSTEMS
SAE AS 85049 : 2016 CONNECTOR ACCESSORIES, ELECTRICAL GENERAL SPECIFICATION FOR
ASTM G 175 : 2013 : REDLINE Standard Test Method for Evaluating the Ignition Sensitivity and Fault Tolerance of Oxygen Pressure Regulators Used for Medical and Emergency Applications
ASTM D 4967 : 1999 : R2013 Standard Guide for Selecting Materials to Be Used for Insulation, Jacketing and Strength Components in Fiber-Optic Cables
MIL-L-15596 Revision G:1988 LOCK, COMBINATION (SAFE AND SAFE LOCKER)
MS21077 Revision H:1994 NUT, SELF-LOCKING, PLATE, TWO LUG, FLOATING, NON-METALLIC INSERT, STEEL 125 KSI FTU, 250 DEG F
MIL-STD-2003-1 Revision A:2009 ELECTRIC PLANT INSTALLATION STANDARD METHODS FOR SURFACE SHIPS AND SUBMARINES (CABLE)
MIL-STD-2003-3 Revision A:2009 ELECTRIC PLANT INSTALLATION STANDARD METHODS FOR SURFACE SHIPS AND SUBMARINES (PENETRATIONS)
MIL-DTL-32258 Base Document:2007 NUT, SELF-LOCKING (RING TYPE NON-METALLIC INSERT), HEAVY HEX, CONTROLLED ROOT RADIUS, NICKEL-COPPER ALLOY
MIL S 8805 : D SWITCHES, AND SWITCH ASSEMBLIES, SENSITIVE AND PUSH, SNAP ACTION, GENERAL SPECIFICATION FOR
MIL S 22885 : E SWITCH, PUSH BUTTON, ILLUMINATED, GENERAL SPECIFICATION FOR
MIL-W-45595-9 Base Document:1992 WASHER, SHOULDERED, GLASS FILLED NYLON
MIL-DTL-28827 Revision C:2011 SWITCHES, THERMOSTATIC, (VOLATILE LIQUID), HERMETICALLY SEALED, GENERAL SPECIFICATION FOR
MIL S 3786 : F SWITCH, ROTARY, CLOSED CONSTRUCTION, 2 AMPERES, LOW LEVEL, POSITIVE SHAFT GROUNDING STYLE SR04
MIL-W-45595 Revision D:1985 WASHER, RECESSED, SADDLE AND SHOULDERED METAL
MIL-DTL-9395 Revision K:2016 Switches, Pressure (Absolute, Gage and Differential) General Specification for
MIL-DTL-22529 Revision D:1996 GROMMET, EDGING
MIL-DTL-24646 Revision C:2015 FUSE BOXES, GENERAL SPECIFICATION FOR
MIL-DTL-24317 Revision B:2010 SWITCHES, MULTISTATION, PUSHBUTTON, ILLUMINATED AND NON-ILLUMINATED), GENERAL SPECIFICATION FOR
MIL-DTL-2726 Revision C:2006 RECEPTACLE, RECEPTACLE PLUGS, SWITCH AND RECEPTACLES, AND OUTLETS (ELECTRICAL), GENERAL SPECIFICATION FOR
SAE J 1639 : 1995(S2017) CLASSIFICATION SYSTEM FOR AUTOMOTIVE POLYAMIDE (PA) PLASTICS
MIL-DTL-24800 Base Document:1996 CLEANING COMPOUND - AQUEOUS - OXYGEN SYSTEMS COMPONENTS
MIL J 39024/11 : F JACK, TIP, TEST POINT TYPE, PRINTED WIRING TYPE, SINGLE TEST POINT, RIGHT ANGLE, 2-LEG MOUNTING, LOW VOLTAGE, .080
MIL-DTL-28754-35 Revision F:2015 CONNECTORS, ELECTRICAL, MODULAR, CONNECTOR, TYPE 3, MALE CONTACT AND INSULATOR BUSHING SET, REMOVABLE WIRE WRAPPOST TERMINAL
MIL-DTL-39024-11 Revision G:2012 Jack, Tip, Test Point Type, Printed Wiring Type, Single Test Point, Right Angle, 2-Leg Mounting, Low Voltage, .080
MIL S 8516 : F SEALING COMPOUND, POLYSULFIDE RUBBER, ELECTRIC CONNECTORS AND ELECTRICAL SYSTEMS CHEMICALLY CURED
DSCC 85068 : B HOLDER, ELECTRICAL CARD, CARD GUIDE, PLASTIC, FASTENER MOUNTED
MIL-C-85049 Revision A:1990 CONNECTOR ACCESSORIES, ELECTRICAL GENERAL SPECIFICATION FOR
MIL-DTL-16878 Revision H:2012 WIRE, ELECTRICAL, INSULATED, GENERAL SPECIFICATION FOR
MIL-HDBK-510 Revision A:2014 AEROSPACE FUELS CERTIFICATION
MS27243 Revision M:2014 Relay, 10 AMP, 4PDT, Sealed, Class O, Accessory
MIL-DTL-24705 Revision B:2010 PENETRATORS, MULTIPLE CABLE, ELECTRIC CABLE, GENERAL SPECIFICATION FOR
MS3187 Revision F:2007 PLUG, END SEAL, FOR MIL-DTL-26482, MIL-DTL-5015, MIL-C-81703 AND MIL-DTL-83723 ELECTRICAL CONNECTORS
MIL C 27072 : B CABLE, POWER, ELECTRICAL & CABLE, SPECIAL PURPOSE ELECTRICAL, MULTICONDUCTOR & SINGLE-SHIELDED - GENERAL SPECIFICATION FOR
MIL-T-62050 Revision B:1985 TANK, COMBAT, FULL TRACKED, 105MM, GUN, M48A5, PROCESSING FOR STORAGE AND SHIPMENT OF
MIL-DTL-28754 Revision E:2016 Connectors, Electrical, Modular, and Component Parts General Specification for
ANSI/AWWA C702 : 2015 COLD-WATER METERS - COMPOUND TYPE
AWWA C701 : 2015 COLD-WATER METERS - TURBINE TYPE, FOR CUSTOMER SERVICE
ANSI/AWWA C514 : 2015 AIR VALVE AND VENT INFLOW PREVENTER ASSEMBLIES FOR POTABLE WATER DISTRIBUTION SYSTEM AND STORAGE FACILITIES
AWWA C703 : 2015 COLD-WATER METERS - FIRE-SERVICE TYPE
ANSI/AWWA C714 : 2013 COLD-WATER METERS FOR RESIDENTIAL FIRE SPRINKLER SYSTEMS IN ONE- AND TWO-FAMILY DWELLINGS AND MANUFACTURED HOMES
SAE AS 81306 : 2017 WIRING INSTALLATION TOOLS FOR BANDS AND TIEDOWN STRAPS
ASTM D 1822M : 1993 Test Method for Tensile-Impact Energy to Break Plastics and Electrical Insulating Materials (Withdrawn 1996)
ASTM F 1733 : 2013 : REDLINE Standard Specification for Butt Heat Fusion Polyamide(PA) Plastic Fitting for Polyamide(PA) Plastic Pipe and Tubing
ASTM D 4000 : 2016 : REDLINE Standard Classification System for Specifying Plastic Materials
ASTM D 955 : 2008 Standard Test Method of Measuring Shrinkage from Mold Dimensions of Thermoplastics
ASTM D 4000 : 2016 Standard Classification System for Specifying Plastic Materials
ASTM F 2945 : 2018 Standard Specification for Polyamide 11 Gas Pressure Pipe, Tubing, and Fittings
ASTM D 256 : 2010 : R2018 Standard Test Methods for Determining the Izod Pendulum Impact Resistance of Plastics
ASTM D 4054 : 2019 Standard Practice for Evaluation of New Aviation Turbine Fuels and Fuel Additives
ASTM F 1733 : 2013 Standard Specification for Butt Heat Fusion Polyamide(PA) Plastic Fitting for Polyamide(PA) Plastic Pipe and Tubing
ASTM G 175 : 2013 Standard Test Method for Evaluating the Ignition Sensitivity and Fault Tolerance of Oxygen Pressure Regulators Used for Medical and Emergency Applications
DSCC 84006F:2022 HOLDER, ELECTRICAL CARD CARD GUIDE, SHALLOW CHANNEL, PLASTIC
NEMA WC 27500 : 2015 STANDARD FOR AEROSPACE AND INDUSTRIAL ELECTRICAL CABLE
MIL PRF 83502 : C SOCKETS, PLUG-IN ELECTRONIC COMPONENTS, ROUND STYLE, GENERAL SPECIFICATION FOR
MIL-DTL-28754-25 Revision B:2014 CONNECTORS, ELECTRICAL, MODULAR, GUIDE, RETAINING
MIL-HDBK-510-1 Revision A:2010 AEROSPACE FUELS CERTIFICATION
MIL-PRF-6106-26 Revision H:2017 Relays, Electromagnetic, 50 Amperes SPST, NO, with 5 Ampere SPDT Auxiliary Hermetically Sealed
SAE AS 81582 : 2017 CONNECTORS, ELECTRICAL, BAYONET COUPLING, ENVIRONMENT RESISTING, UMBILICAL, GENERAL SPECIFICATION FOR
MIL E 917 : E ELECTRIC POWER EQUIPMENT, BASIC REQUIREMENTS (NAVAL SHIPBOARD USE)
MIL-DTL-28754-37 Revision E:2015 CONNECTORS, ELECTRICAL, MODULAR, CONNECTOR, TYPE 3, FEMALE CONTACT AND POLARIZING BUSHING SET, REMOVABLE WIRE WRAPPOST TERMINAL
MIL-DTL-27500 Revision H:1997 CABLE, POWER, ELECTRICAL AND CABLE SPECIAL PURPOSE, ELECTRICAL SHIELDED AND UNSHIELDED, GENERAL SPECIFICATION FOR
MIL-DTL-27072 Revision F:2018 Cable, Power, Electrical and Cable, Special Purpose, Electrical, Multiconductor and Single Shielded, General Specification for
MIL-N-85615-8 Base Document:1989 NUT, SELF-SEALING, SELF-LOCKING, ALLOY STEEL, 125 KSI FTU, 250 DEGREES F & 450 DEGREES F
MIL-PRF-8516 Revision G:1997 SEALING COMPOUND, SYNTHETIC RUBBER, ELECTRIC CONNECTORS AND ELECTRIC SYSTEMS, CHEMICALLY CURED
MS90578 Revision C:2012 ADAPTER, CONNECTOR, (TWIN BINDING POST-BNC MALE) TYPE UG-1441/U
MIL B 8565 : J BATTERY AND CELL, STORAGE, AIRCRAFT, GENERAL SPECIFICATION FOR
MIL-DTL-2 Revision G:2006 VALVES, CYLINDER, GAS (FOR COMPRESSED OR LIQUEFIED GASES), GENERAL SPECIFICATION FOR
MIL-DTL-641 Revision G:2015 JACKS, TELEPHONE, GENERAL SPECIFICATION FOR
A-A-55628 Revision A:1998 NUT, PLAIN, CAP, HIGH CROWN UNC-2B AND UNF-2B
MIL-A-24780 Base Document:1992 ACTUATING ASSEMBLY, SINGLE LINEAR MOTION, FOR THE REMOTE ACTUATION OF QUICK ACTING VALVES, GENERAL SPECIFICATION FOR
MIL-DTL-28754-34 Revision E:2015 CONNECTORS, ELECTRICAL, MODULAR, CONNECTOR, TYPE 3, FEMALE CONTACT AND INSULATOR BUSHING SET, REMOVABLE WIRE WRAPPOST TERMINAL
MIL-DTL-13777 Revision L:2014 CABLE, SPECIAL PURPOSE, ELECTRICAL, GENERAL SPECIFICATION FOR
MIL-DTL-55302-127 Revision C:2004 Connectors, Printed Circuit Subassembly and Accessories: Receptacle, Single Row, 2 through 65 Contact Positions, for Printed Wiring Boards (.062\" , .093\" , .125\" ) (.100 Spacing)
FF-N-836 Revision E:1994 Nut: Square, Hexagon, Cap, Slotted, Castle, Knurled, Welding and Single Ball Seat
CSA B137 COMPENDIUM : 2017 THERMOPLASTIC PRESSURE PIPING COMPENDIUM
MIL-DTL-3849-11 Revision C:2005 CORDS, ELECTRICAL (TINSEL), CLASS PSP, POLYAMIDE INSULATED (EXTRUDED), STYRENE BUTADIENE RUBBER (SBR) JACKETED AND POLYAMIDE BRAIDED
ASTM D 955 : 2008 : R2014 Standard Test Method of Measuring Shrinkage from Mold Dimensions of Thermoplastics
DSCC 89029 : B HOLDER, ELECTRICAL CARD, CARD GUIDE, CONDUCTIVE PLASTIC, ANTI-VIBRATION
ASTM D 4967 : 1999 : R2004 : EDT 1 Standard Guide for Selecting Materials to Be Used for Insulation, Jacketing and Strength Components in Fiber-Optic Cables
ASTM D 638 : 2014 : REDLINE Standard Test Method for Tensile Properties of Plastics
AWWA C713 : 2015 COLD-WATER METERS - FLUIDIC-OSCILLATOR TYPE
AWWA C704 : 2015 PROPELLER-TYPE METERS FOR WATERWORKS APPLICATIONS
ASTM D 1897 : 1988 Recommended Practice for Injection Molding Test Specimens of Thermoplastic Molding and Extrusion Materials (Withdrawn 1992)
ASTM D 4967 : 1999 : R2009 Standard Guide for Selecting Materials to Be Used for Insulation, Jacketing and Strength Components in Fiber-Optic Cables
API 14F : 2008 : R2013 DESIGN, INSTALLATION, AND MAINTENANCE OF ELECTRICAL SYSTEMS FOR FIXED AND FLOATING OFFSHORE PETROLEUM FACILITIES FOR UNCLASSIFIED AND CLASS 1, DIVISION 1 AND DIVISION 2 LOCATIONS
AWWA C712 : 2019 COLD-WATER METERS - SINGLEJET TYPE
NASA KSC SPEC E 0031 : 2008 CABLES, ELECTRICAL, SPECIFICATION FOR
NASA KSC SPEC E 0024 : 2008 CABLE, ELECTRICAL, SHIELDED, JACKETED, FOR HARNESS ASSEMBLIES, GENERAL SPECIFICATION FOR
MIL-DTL-43101 Revision B:2013 FILING CABINET, LETTER SIZE DESIGN, STEEL, OD, ONE DRAWER HIGH, ONE DRAWER WIDE
IPC HDBK 630 : 0 GUIDELINES FOR DESIGN, MANUFACTURE, INSPECTION AND TESTING OF ELECTRONIC ENCLOSURES ASSEMBLY
MIL C 3432 : F CABLE, [POWER AND SPECIAL PURPOSE] AND WIRE ELECTRICAL [300 AND 600 VOLTS]
MIL-DTL-81306 Revision B:2007 TOOL, INSTALLATION FOR ADJUSTABLE PLASTIC AND METAL TIEDOWN STRAPS
MIL L 3661 : B LAMPHOLDER, INDICATOR LIGHTS, INDICATOR LIGHT HOUSINGS AND INDICATOR LIGHT LENSES GENERAL SPECIFICATION FOR
MIL-DTL-25955 Revision A:2004 CONNECTORS, ELECTRICAL, ENVIRONMENT RESISTING, MINIATURE, WITH SNAP-IN CONTACTS, OR HERMETICALLY SEALED WITH NON-REMOVABLE CONTACTS, GENERAL SPECIFICATION FOR
ANSI/AWWA C710 : 2015 COLD-WATER METERS - DISPLACEMENT TYPE, PLASTIC MAIN CASE
MIL-DTL-39024-10 Revision F:2015 JACK, TIP (TEST POINT TYPE, PANEL TYPE; SINGLE TEST POINT (THREADED) LOW VOLTAGE, .080)
MIL-DTL-9177-1 Revision C:2002 CONNECTOR, AUDIO, AIRBORNE, PLUG, 4 CONTACT
MIL C 28754 : D CONNECTOR, ELECTRICAL, MODULAR AND COMPONENT PARTS, GENERAL SPECIFICATION FOR
DSCC 86100 : D CONNECTORS, ELECTRICAL, UNSHROUDED HEADERS, PWB TERMINATION
MIL-DTL-642-14 Revision B:2013 PLUGS, TELEPHONE (TYPE U-384/U) 5 CONDUCTOR, SINGLE
MIL B 49450 : 0 BATTERY, RECHARGEABLE, NICKEL CADMIUM, VENTED, AIRCRAFT,BB-716/A
ASTM D 695M : 1991 Test Method for Compressive Properties of Rigid Plastics (Metric) (Withdrawn 1996)
DSCC 86037 : B CONNECTORS, RECEPTACLE, ELECTRICAL, LATCH HOUSINGS, CRIMP TO WIRE CONTACTS, GENERAL DRAWING FOR
AWWA C712 : 2015 COLD-WATER METERS - SINGLEJET TYPE
ASTM D 4967 : 1999 Standard Guide for Selecting Materials to Be Used for Insulation, Jacketing and Strength Components in Fiber-Optic Cables
API 14F:2008 DESIGN, INSTALLATION, AND MAINTENANCE OF ELECTRICAL SYSTEMS FOR FIXED AND FLOATING OFFSHORE PETROLEUM FACILITIES FOR UNCLASSIFIED AND CLASS 1, DIVISION 1 AND DIVISION 2 LOCATIONS
AWWA C702 : 2019 COLD-WATER METERS - COMPOUND TYPE
MIL-PRF-81757-9 Revision D:2013 BATTERY, STORAGE, AIRCRAFT, NICKEL-CADMIUM, 24 VOLTS, 30 AMPERE-HOUR (BB-433A/A)
DSCC 84006 : E HOLDER, ELECTRICAL CARD, CARD GUIDE, SHALLOW CHANNEL, PLASTIC
ASTM D 638M : 1996 Standard Test Method for Tensile Properties of Plastics (Metric) (Withdrawn 1998)
MIL-DTL-83502 Revision E:2007 Sockets, Plug-in Electronic Components, Round Style, General Specification for
MIL W 16878 : F WIRE, ELECTRICAL, INSULATED, GENERAL SPECIFICATION FOR
MIL C 55021 : B CABLE, ELECTRICAL, SHIELDED SINGLES, SHIELDED AND JACKETED SINGLES, TWISTED PAIRS AND TRIPLES, INTERNAL HOOKUP
MIL-DTL-55021 Revision D:2011 CABLE, ELECTRICAL, SHIELDED SINGLES, SHIELDED AND JACKETED SINGLES, TWISTED PAIRS AND TRIPLES, INTERNAL HOOKUP, GENERAL SPECIFICATION FOR
SAE J 2260 : 2004 NONMETALLIC FUEL SYSTEM TUBING WITH ONE OR MORE LAYERS
MIL-DTL-21097-11 Revision J:2005 Connectors, Electrical, Printed Wiring Board Keys, Polarizing
ASTM D 6110 : 2018 : REDLINE Standard Test Method for Determining the Charpy Impact Resistance of Notched Specimens of Plastics
MIL-DTL-3390 Revision H:2011 RINGS, DEE
AWWA C700 : 2015 COLD-WATER METERS - DISPLACEMENT TYPE, METAL ALLOY MAIN CASE
ASTM D 5420 : 2016 : REDLINE Standard Test Method for Impact Resistance of Flat, Rigid Plastic Specimen by Means of a Striker Impacted by a Falling Weight (Gardner Impact)
ASTM D 2289 : 1984 Method of Test for Tensile Properties of Plastics at High Speeds (Withdrawn 1990)
MIL-DTL-3432 Revision J:2009 CABLES, (POWER AND SPECIAL PURPOSE) AND WIRE, ELECTRICAL (300 AND 600 VOLTS)
ASTM F 2767 : 2012-12 SPECIFICATION FOR ELECTROFUSION TYPE POLYAMIDE-12 FITTINGS FOR OUTSIDE DIAMETER CONTROLLED POLYAMIDE-12 PIPE AND TUBING FOR GAS DISTRIBUTION
MIL R 3390 : F RINGS, DEE
DSCC 85076 : B HOLDER, ELECTRICAL CARD, CARD GUIDE, PLASTIC
ASTM D 638 : 2014 Standard Test Method for Tensile Properties of Plastics
ASTM D 5420 : 2016 Standard Test Method for Impact Resistance of Flat, Rigid Plastic Specimen by Means of a Striker Impacted by a Falling Weight (Gardner Impact)
ASTM F 1836M : 2015 : R2019 Standard Specification for Stuffing Tubes, Nylon, and Packing Assemblies (Metric)
SAE AS 81703 : 2012 CONNECTORS, ELECTRIC, CIRCULAR, MINIATURE, RACK AND PANEL OR PUSH-PULL COUPLING, ENVIRONMENT RESISTING
NASM 21083 : 2004 NUT, SELF-LOCKING, HEXAGON, NON-METALLIC INSERT, LOW HEIGHT, 250 DEGREES F
DSCC 84101 : F HOLDER, ELECTRICAL CARD, CARD GUIDE, DEEP CHANNEL, PLASTIC
SAE AS 23190 : 2015 WIRING, POSITIONING, AND SUPPORT ACCESSORIES
NSF 14 : 2016 PLASTICS PIPING SYSTEM COMPONENTS AND RELATED MATERIALS
API 14FZ : 2013 RECOMMENDED PRACTICE FOR DESIGN, INSTALLATION, AND MAINTENANCE OF ELECTRICAL SYSTEMS FOR FIXED AND FLOATING OFFSHORE PETROLEUM FACILITIES FOR UNCLASSIFIED AND CLASS 1, ZONE 0, ZONE 1, AND ZONE 2 LOCATIONS
API 14F REDLINE : 2008 DESIGN, INSTALLATION, AND MAINTENANCE OF ELECTRICAL SYSTEMS FOR FIXED AND FLOATING OFFSHORE PETROLEUM FACILITIES FOR UNCLASSIFIED AND CLASS 1, DIVISION 1 AND DIVISION 2 LOCATIONS
MIL-DTL-18714 Revision F:2012 PRIMER, ELECTRIC, MARK 45 MOD 1
ASME A112.6.4 : 2003 : R2008 ROOF, DECK, AND BALCONY DRAINS
ASME A112.6.4 : 2003 : R2012 ROOF, DECK, AND BALCONY DRAINS
ASME A112.6.4 : 2003 ROOF, DECK, AND BALCONY DRAINS

ASTM D 1600 : 1999 Standard Terminology for Abbreviated Terms Relating to Plastics
ISO 75-1:2013 Plastics Determination of temperature of deflection under load Part 1: General test method
ASTM D 6779 : 2002 Standard Classification System for Polyamide Molding and Extrusion Materials (PA)
ASTM D 6779 : 2005 Standard Classification System for Polyamide Molding and Extrusion Materials (PA)
ASTM D 3418 : 2015 : REDLINE Standard Test Method for Transition Temperatures and Enthalpies of Fusion and Crystallization of Polymers by Differential Scanning Calorimetry
ASTM D 6779 : 2007 : REV A Standard Classification System for Polyamide Molding and Extrusion Materials (PA)
ASTM D 3418 : 2012 : EDT 1 Standard Test Method for Transition Temperatures and Enthalpies of Fusion and Crystallization of Polymers by Differential Scanning Calorimetry
ASTM D 4000 : 2013 Standard Classification System for Specifying Plastic Materials
ASTM D 618 : 2013 : REDLINE Standard Practice for Conditioning Plastics for Testing
ASTM D 3418 : 1982 : R1988 : EDT 1 Standard Test Method for Transition Temperatures of Polymers By Thermal Analysis
ISO 3167:2014 Plastics Multipurpose test specimens
ASTM D 3418 : 1999 Standard Test Method for Transition Temperatures of Polymers By Differential Scanning Calorimetry
ASTM D 4000 : 2003 : REV A Standard Classification System for Specifying Plastic Materials
ASTM D 6779 : 2003 Standard Classification System for Polyamide Molding and Extrusion Materials (PA)
ASTM D 4000 : 2000 : REV A Standard Classification System for Specifying Plastic Materials
ASTM D 4000 : 2012 Standard Classification System for Specifying Plastic Materials
ASTM D 4000 : 2009 Standard Classification System for Specifying Plastic Materials
ASTM D 3641 : 2002 Standard Practice for Injection Molding Test Specimens of Thermoplastic Molding and Extrusion Materials
ASTM D 3892 : 1993 : R2003 Standard Practice for Packaging/Packing of Plastics
ASTM D 6779 : 2011 Standard Classification System for Polyamide Molding and Extrusion Materials (PA)
ASTM D 4000 : 2011 Standard Classification System for Specifying Plastic Materials
ASTM D 6779 : 2008 Standard Classification System for Polyamide Molding and Extrusion Materials (PA)
ASTM D 3892 : 1993 : R1998 Standard Practice for Packaging/Packing of Plastics
ASTM D 3641 : 2015 : REDLINE Standard Practice for Injection Molding Test Specimens of Thermoplastic Molding and Extrusion Materials
ASTM D 6779 : 2017 : REDLINE Standard Classification System for and Basis of Specification for Polyamide Molding and Extrusion Materials (PA)
ASTM D 6779 : 2004 Standard Classification System for Polyamide Molding and Extrusion Materials (PA)
ASTM D 1600 : 2007 Standard Terminology for Abbreviated Terms Relating to Plastics
ASTM D 792 : 2013 : REDLINE Standard Test Methods for Density and Specific Gravity (Relative Density) of Plastics by Displacement
ASTM D 4000 : 2004 : EDT 1 Standard Classification System for Specifying Plastic Materials
ASTM D 1600 : 2013 Standard Terminology for Abbreviated Terms Relating to Plastics
ASTM D 6779 : 2012 Standard Classification System for and Basis of Specification for Polyamide Molding and Extrusion Materials (PA)
ASTM D 3418 : 2012 Standard Test Method for Transition Temperatures and Enthalpies of Fusion and Crystallization of Polymers by Differential Scanning Calorimetry
ASTM D 3641 : 2010 Standard Practice for Injection Molding Test Specimens of Thermoplastic Molding and Extrusion Materials
ASTM D 1600 : 2014 Standard Terminology for Abbreviated Terms Relating to Plastics
ASTM D 6779 : 2006 Standard Classification System for Polyamide Molding and Extrusion Materials (PA)
ASTM D 3418 : 2003 Standard Test Method for Transition Temperatures and Enthalpies of Fusion and Crystallization of Polymers by Differential Scanning Calorimetry
ISO 75-2:2013 Plastics — Determination of temperature of deflection under load — Part 2: Plastics and ebonite
ASTM D 1600 : 2008 Standard Terminology for Abbreviated Terms Relating to Plastics
ASTM D 3418 : 2015 Standard Test Method for Transition Temperatures and Enthalpies of Fusion and Crystallization of Polymers by Differential Scanning Calorimetry
ISO 527-2:2012 Plastics — Determination of tensile properties — Part 2: Test conditions for moulding and extrusion plastics
ISO 1874-2:2012 Plastics Polyamide (PA) moulding and extrusion materials Part 2: Preparation of test specimens and determination of properties
ASTM D 4000 : 2009 : REV B Standard Classification System for Specifying Plastic Materials
ASTM D 3641 : 2015 Standard Practice for Injection Molding Test Specimens of Thermoplastic Molding and Extrusion Materials
ASTM D 4000 : 2000 Standard Classification System for Specifying Plastic Materials
ASTM D 3641 : 2010 : REV A Standard Practice for Injection Molding Test Specimens of Thermoplastic Molding and Extrusion Materials
ASTM D 4000 : 2010 : REV A Standard Classification System for Specifying Plastic Materials
ISO 1183:1987 Plastics Methods for determining the density and relative density of non-cellular plastics
ASTM D 3641 : 2014 Standard Practice for Injection Molding Test Specimens of Thermoplastic Molding and Extrusion Materials
ASTM D 4000 : 2007 Standard Classification System for Specifying Plastic Materials
ASTM D 4000 : 2009 : REV A Standard Classification System for Specifying Plastic Materials
ASTM D 5630 : 2013 Standard Test Method for Ash Content in Plastics (Withdrawn 2022)
ISO 180:2000 Plastics Determination of Izod impact strength
ASTM D 4000 : 2001 Standard Classification System for Specifying Plastic Materials
ASTM D 5630 : 1994 Standard Test Method for Ash Content in Thermoplastics
ASTM D 4000 : 2008 Standard Classification System for Specifying Plastic Materials
ISO 3146:2000 Plastics — Determination of melting behaviour (melting temperature or melting range) of semi-crystalline polymers by capillary tube and polarizing-microscope methods
ASTM D 6779 : 2004 : REV A Standard Classification System for Polyamide Molding and Extrusion Materials (PA)
ASTM D 790 : 2017 : REDLINE Standard Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials
ASTM D 5630 : 2013 : REDLINE Standard Test Method for Ash Content in Plastics (Withdrawn 2022)
ASTM D 1600 : 2018 Standard Terminology for Abbreviated Terms Relating to Plastics (Withdrawn 2024)
ASTM D 6779 : 2012 : REV A Standard Classification System for and Basis of Specification for Polyamide Molding and Extrusion Materials (PA)
ISO 307:2007 Plastics Polyamides Determination of viscosity number
ASTM D 3418 : 2008 Standard Test Method for Transition Temperatures and Enthalpies of Fusion and Crystallization of Polymers by Differential Scanning Calorimetry
ASTM D 4000 : 2001 : REV A : EDT 1 Standard Classification System for Specifying Plastic Materials
ASTM D 6779 : 2002 : REV A Standard Classification System for Polyamide Molding and Extrusion Materials (PA)
ASTM D 648 : 2016 Standard Test Method for Deflection Temperature of Plastics Under Flexural Load in the Edgewise Position
ASTM D 4000 : 2004 Standard Classification System for Specifying Plastic Materials
ISO 294-1:2017 Plastics — Injection moulding of test specimens of thermoplastic materials — Part 1: General principles, and moulding of multipurpose and bar test specimens
ASTM D 257 : 2014 : REDLINE Standard Test Methods for DC Resistance or Conductance of Insulating Materials
L-P-410 Revision A:1966 PLASTIC, POLYAMIDE (NYLON), RIGID: RODS, TUBES, FLATS, MOLDED AND CAST PARTS
ASTM D 5630 : 2001 Standard Test Method for Ash Content in Thermoplastics
ASTM D 3892 : 1993 : R2009 Standard Practice for Packaging/Packing of Plastics
ASTM D 4000 : 2010 Standard Classification System for Specifying Plastic Materials
ASTM D 6779 : 2016 Standard Classification System for and Basis of Specification for Polyamide Molding and Extrusion Materials (PA)
ASTM D 6779 : 2007 Standard Classification System for Polyamide Molding and Extrusion Materials (PA)
ISO 960:1988 Plastics — Polyamides (PA) — Determination of water content
ASTM D 5630 : 2006 Standard Test Method for Ash Content in Plastics
ASTM D 3641 : 1997 Standard Practice for Injection Molding Test Specimens of Thermoplastic Molding and Extrusion Materials
ISO 178:2010 Plastics Determination of flexural properties
ASTM D 3641 : 2012 Standard Practice for Injection Molding Test Specimens of Thermoplastic Molding and Extrusion Materials
ASTM D 6779 : 2010 Standard Classification System for Polyamide Molding and Extrusion Materials (PA)
ASTM D 4000 : 2003 Standard Classification System for Specifying Plastic Materials
ISO 3451-4:1998 Plastics — Determination of ash — Part 4: Polyamides
ASTM D 6260 : 1998 Standard Test Method for Gravimetric Determination of Carbon Black in Nylon Materials (PA) (Withdrawn 2004)
ASTM D 638 : 2014 : REDLINE Standard Test Method for Tensile Properties of Plastics
ASTM D 3892 : 2015 : REDLINE PRACTICE FOR PACKAGING/PACKING OF PLASTICS
ISO 527-1:2012 Plastics Determination of tensile properties Part 1: General principles
ASTM D 6779 : 2017 Standard Classification System for and Basis of Specification for Polyamide Molding and Extrusion Materials (PA)
ASTM D 6779 : 2008 : REV A Standard Classification System for Polyamide Molding and Extrusion Materials (PA)
ASTM D 6779 : 2006 : EDT 1 Standard Classification System for Polyamide Molding and Extrusion Materials (PA)
ASTM D 4000 : 2016 : REDLINE Standard Classification System for Specifying Plastic Materials

View more information
£69.29
Excluding VAT

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.