• There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

ASTM D 4129 : 2005 : R2013

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Standard Test Method for Total and Organic Carbon in Water by High Temperature Oxidation and by Coulometric Detection
Available format(s)

Hardcopy , PDF

Superseded date

21-01-2020

Language(s)

English

Published date

24-06-2013

CONTAINED IN VOL. 11.02, 2017 Describes the determination of total and organic carbon in water and waste water, including brackish waters and brines in the range from 2 to 20000 mg/L.

1.1This test method covers the determination of total and organic carbon in water and waste water, including brackish waters and brines in the range from 2 to 20000 mg/L. This test method has the advantages of a wide range of concentration which may be determined without sample dilution and the provision for boat or capillary introduction of samples containing sediments and particulate matter where syringe injection is inappropriate.

1.2This procedure is applicable only to that carbonaceous matter in the sample that can be introduced into the reaction zone. When syringe injection is used to introduce samples into the combustion zone, the syringe needle opening size limits the maximum size of particles that can be present in samples. Sludge and sediment samples must be homogenized prior to sampling with a micropipetor or other appropriate sampler and ladle introduction into the combustion zone is required.

1.3The precision and bias information reported in this test method was obtained in collaborative testing that included waters of the following types: distilled, deionized, potable, natural, brine, municipal and industrial waste, and water derived from oil shale retorting. Since the precision and bias information reported may not apply to waters of all matrices, it is the user's responsibility to ensure the validity of this test method on samples of other matrices.

1.4The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.

1.5This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific precautionary statements, see 9.1 and 10.2.1.

Committee
D 19
DocumentType
Test Method
Pages
8
ProductNote
Reconfirmed 2013
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy
Supersedes

ASTM D 5338 : 2015 Standard Test Method for Determining Aerobic Biodegradation of Plastic Materials Under Controlled Composting Conditions, Incorporating Thermophilic Temperatures
ASTM F 1581 : 2008 : R2016 Standard Specification for Composition of Anorganic Bone for Surgical Implants
ASTM D 5359 : 1998 : R2015 Standard Specification for Glass Cullet Recovered from Waste for Use in Manufacture of Glass Fiber
ASTM D 7475 : 2011 Standard Test Method for Determining the Aerobic Degradation and Anaerobic Biodegradation of Plastic Materials under Accelerated Bioreactor Landfill Conditions
ASTM C 1750 : 2017 Standard Guide for Development, Verification, Validation, and Documentation of Simulated High-Level Tank Waste
ASTM D 5975 : 2017 Standard Test Method for Determining the Stability of Compost by Measuring Oxygen Consumption
ASTM D 5511 : 2018 Standard Test Method for Determining Anaerobic Biodegradation of Plastic Materials Under High-Solids Anaerobic-Digestion Conditions
ASTM D 5173 : 2015 Standard Guide for On-Line Monitoring of Total Organic Carbon in Water by Oxidation and Detection of Resulting Carbon Dioxide
ASTM D 6691 : 2017 Standard Test Method for Determining Aerobic Biodegradation of Plastic Materials in the Marine Environment by a Defined Microbial Consortium or Natural Sea Water Inoculum
ASTM D 3694 : 1996 : R2017 Standard Practices for Preparation of Sample Containers and for Preservation of Organic Constituents
ASTM D 5526 : 2018 Standard Test Method for Determining Anaerobic Biodegradation of Plastic Materials Under Accelerated Landfill Conditions
ASTM D 4839 : 2003 : R2017 Standard Test Method for Total Carbon and Organic Carbon in Water by Ultraviolet, or Persulfate Oxidation, or Both, and Infrared Detection
ASTM E 688 : 1994 : R2011 Standard Test Methods for Waste Glass as a Raw Material for Glass Manufacturing (Withdrawn 2019)

ASTM D 3370 : 1995 : REV A : R2003 : EDT 1 Standard Practices for Sampling Water from Closed Conduits
ASTM D 1129 : 2013 : REDLINE Standard Terminology Relating to Water
ASTM D 1129 : 2003 Standard Terminology Relating to Water
ASTM D 1129 : 2013 Standard Terminology Relating to Water
ASTM D 1193 : 1977 : R1983 : EDT 1 Standard Specification for Reagent Water
ASTM D 1129 : 2006 Standard Terminology Relating to Water
ASTM D 3370 : 2010 Standard Practices for Sampling Water from Closed Conduits
ASTM D 3370 : 2008 Standard Practices for Sampling Water from Closed Conduits
ASTM D 1129 : 1999 : REV A Standard Terminology Relating to Water
ASTM D 3856 : 2011 Standard Guide for Management Systems in Laboratories Engaged in Analysis of Water
ASTM D 1129 : 2006 : REV A Standard Terminology Relating to Water
ASTM D 1193 : 2006 : R2011 Standard Specification for Reagent Water
ASTM D 1129 : 2003 : REV A Standard Terminology Relating to Water
ASTM D 1129 : 2002 Standard Terminology Relating to Water
ASTM D 513 : 2016 : REDLINE Standard Test Methods for Total and Dissolved Carbon Dioxide in Water
ASTM D 1193 : 1991 Standard Specification for Reagent Water
ASTM D 3856 : 1995 : R2006 Standard Guide for Good Laboratory Practices in Laboratories Engaged in Sampling and Analysis of Water
ASTM D 1129 : 2004 Standard Terminology Relating to Water
ASTM D 3856 : 2011 : R2015 Standard Guide for Management Systems in Laboratories Engaged in Analysis of Water (Withdrawn 2024)
ASTM D 3856 : 1995 : R2000 Standard Guide for Good Laboratory Practices in Laboratories Engaged in Sampling and Analysis of Water
ASTM D 3370 : 2018 Standard Practices for Sampling Water from Flowing Process Streams
ASTM D 1129 : 2002 : REV A Standard Terminology Relating to Water
ASTM D 3370 : 1976 Standard Practices for Sampling Water
ASTM D 1193 : 1970 Standard Specification For Reagent Water
ASTM D 1193 : 2006 Standard Specification for Reagent Water
ASTM D 3370 : 1995 : REV A : R1999 : EDT 1 Standard Practices for Sampling Water from Closed Conduits
ASTM D 1193 : 1999 Standard Specification for Reagent Water
ASTM D 1129 : 2010 Standard Terminology Relating to Water
ASTM D 4210 : 1989 : R1996 : EDT 1 Standard Practice for Intralaboratory Quality Control Procedures and a Discussion on Reporting Low-Level Data (Withdrawn 2002)
ASTM D 3370 : 2007 Standard Practices for Sampling Water from Closed Conduits
ASTM D 1129 : 2006 : REV A : EDT 1 Standard Terminology Relating to Water
ASTM D 1129 : 2001 Standard Terminology Relating to Water
ASTM D 1129 : 2004 : EDT 1 Standard Terminology Relating to Water
ASTM D 1193 : 2006 : R2018 Standard Specification for Reagent Water

View more information
£62.61
Excluding VAT

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.