• There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

ASTM D 5144 : 2008

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Standard Guide for Use of Protective Coating Standards in Nuclear Power Plants
Available format(s)

Hardcopy , PDF

Superseded date

11-11-2014

Language(s)

English

Published date

15-11-2008

CONTAINED IN VOL. 06.02, 2017 Gives a common basis on which protective coatings for the surfaces of nuclear power generating facilities may be qualified and selected by reproducible evaluation tests.

1.1 This guide provides a common basis on which protective coatings for the surfaces of nuclear power generating facilities may be qualified and selected by reproducible evaluation tests. This guide also provides guidance for application and maintenance of protective coatings. Under the environmental operating and accident conditions of nuclear power generation facilities, encompassing pressurized water reactors (PWRs) and boiling water reactors (BWRs), coating performance may be affected by exposure to any one, all, or a combination of the following conditions: ionizing radiation; contamination by radioactive nuclides and subsequent decontamination processes; chemical and water sprays; high-temperature high-pressure steam; and abrasion or wear.

1.2 The content of this guide includes:

Section
Referenced Documents2
Terminology3
Significance and Use4
Coating MaterialTesting5
Thermal Conductivity5
Surface Preparation, Coating Application, and Inspection for
Shop and Field Work
6
Quality Assurance7
Keywords8

1.2.1 In addition, this guide addresses technical topics within ANSI N5.12 and ANSI N101.2 that are covered by separate ASTM standards, for example, surface preparation, (shop and field) and coating application, (shop and field).

1.2.2 Applicable sections of this guide and specific acceptance criteria may be incorporated into specifications and other documents where appropriate.

1.3 The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard.

1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Committee
D 33
DevelopmentNote
Supersedes ASTM D 3842 (12/2001)
DocumentType
Guide
Pages
6
ProductNote
Reconfirmed 2008
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy
Supersedes

ASTM D 4538 : 2015 Standard Terminology Relating to Protective Coating and Lining Work for Power Generation Facilities
ASTM D 8157 : 2019 Standard Guide for Qualification Testing of Coatings Used in Coating Service Level I in Nuclear Power Plants
ASTM D 8104 : 2017 Standard Guide for Determining Coating Qualification Test Data Applicability
ASTM D 5498 : 2012 : REV A : R2018 Standard Guide for Developing a Training Program for Personnel Performing Coating and Lining Work Inspection for Nuclear Facilities
ASTM D 7230 : 2006 : R2013 Standard Guide for Evaluating Polymeric Lining Systems for Water Immersion in Coating Service Level III Safety-Related Applications on Metal Substrates
ASTM C 1533 : 2015 Standard Guide for General Design Considerations for Hot Cell Equipment
ASTM D 3843 : 2016 Standard Practice for Quality Assurance for Protective Coatings Applied to Nuclear Facilities
ASTM C 1217 : 2000 : R2012 Standard Guide for Design of Equipment for Processing Nuclear and Radioactive Materials

ANSI N101.2 : 1972 PROTECTIVE COATINGS (PAINTS) FOR LIGHT WATER NUCLEAR REACTOR CONTAINMENT FACILITIES
CFR 10(PTS0-199) : JAN 87 ENERGY - NUCLEAR REGULATORY COMMISSION
ASTM D 7234 : 2012 : REDLINE Standard Test Method for Pull-Off Adhesion Strength of Coatings on Concrete Using Portable Pull-Off Adhesion Testers
ASTM D 4541 : 2017 : REDLINE Standard Test Method for Pull-Off Strength of Coatings Using Portable Adhesion Testers
ASTM D 5163 : 2016 : REDLINE Standard Guide for Establishing a Program for Condition Assessment of Coating Service Level I Coating Systems in Nuclear Power Plants
ASTM E 1461 : 2013 : REDLINE Standard Test Method for Thermal Diffusivity by the Flash Method
ASTM D 3911 : 2016 : REDLINE Standard Test Method for Evaluating Coatings Used in Light-Water Nuclear Power Plants at Simulated Design Basis Accident (DBA) Conditions
ANSI N512 : 1974 PROTECTIVE COATINGS (PAINTS) FOR THE NUCLEAR INDUSTRY
ASTM D 3843 : 2016 : REDLINE Standard Practice for Quality Assurance for Protective Coatings Applied to Nuclear Facilities
ASME PV CODE 11 : 2017 BOILER AND PRESSURE VESSEL CODE - RULES FOR INSERVICE INSPECTION OF NUCLEAR POWER PLANT COMPONENTS
ASTM D 4538 : 2015 : REDLINE Standard Terminology Relating to Protective Coating and Lining Work for Power Generation Facilities

View more information
£62.61
Excluding VAT

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.