ASTM D 5144 : 2008 : R2016
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
Standard Guide for Use of Protective Coating Standards in Nuclear Power Plants
Available format(s)
Hardcopy , PDF
Superseded date
26-02-2021
Language(s)
English
Published date
22-08-2016
CONTAINED IN VOL. 06.02, 2017 Gives a common basis on which protective coatings for the surfaces of nuclear power generating facilities may be qualified and selected by reproducible evaluation tests.
1.1This guide provides a common basis on which protective coatings for the surfaces of nuclear power generating facilities may be qualified and selected by reproducible evaluation tests. This guide also provides guidance for application and maintenance of protective coatings. Under the environmental operating and accident conditions of nuclear power generation facilities, encompassing pressurized water reactors (PWRs) and boiling water reactors (BWRs), coating performance may be affected by exposure to any one, all, or a combination of the following conditions: ionizing radiation; contamination by radioactive nuclides and subsequent decontamination processes; chemical and water sprays; high-temperature high-pressure steam; and abrasion or wear.
1.2The content of this guide includes:
| Section | |
| Referenced Documents | 2 |
| Terminology | 3 |
| Significance and Use | 4 |
| Coating Material Testing | 5 |
| Thermal Conductivity | 5 |
| Surface Preparation, Coating Application, and Inspection for | 6 |
| Quality Assurance | 7 |
| Keywords | 8 |
1.2.1In addition, this guide addresses technical topics within ANSI N5.12 and ANSI N101.2 that are covered by separate ASTM standards, for example, surface preparation, (shop and field) and coating application, (shop and field).
1.2.2Applicable sections of this guide and specific acceptance criteria may be incorporated into specifications and other documents where appropriate.2
1.3The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard.
1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
| Committee |
D 33
|
| DevelopmentNote |
Supersedes ASTM D 3842 (12/2001)
|
| DocumentType |
Guide
|
| Pages |
6
|
| ProductNote |
Reconfirmed 2016
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| ASTM C 1217 : 2000 : R2020 | Standard Guide for Design of Equipment for Processing Nuclear and Radioactive Materials |
| ASTM D 7108 : 2012 : R2018 | Standard Guide for Establishing Qualifications for a Nuclear Coatings Specialist |
| ASTM G 195 : 2018 | Standard Guide for Conducting Wear Tests Using a Rotary Platform Abraser |
| ASTM D 8104 : 2017 | Standard Guide for Determining Coating Qualification Test Data Applicability |
| ASTM C 1217 : 2000 : R2012 | Standard Guide for Design of Equipment for Processing Nuclear and Radioactive Materials |
| ASTM D 7230 : 2006 : R2013 | Standard Guide for Evaluating Polymeric Lining Systems for Water Immersion in Coating Service Level III Safety-Related Applications on Metal Substrates |
| ASTM C 1533 : 2015 | Standard Guide for General Design Considerations for Hot Cell Equipment |
| ASTM D 4538 : 2015 | Standard Terminology Relating to Protective Coating and Lining Work for Power Generation Facilities |
| ASTM D 8157 : 2019 | Standard Guide for Qualification Testing of Coatings Used in Coating Service Level I in Nuclear Power Plants |
| ASTM D 5498 : 2012 : REV A : R2018 | Standard Guide for Developing a Training Program for Personnel Performing Coating and Lining Work Inspection for Nuclear Facilities |
| ASTM D 3843 : 2016 | Standard Practice for Quality Assurance for Protective Coatings Applied to Nuclear Facilities |
| ASTM D 5139 : 1990 : R2001 | Standard Specification for Sample Preparation for Qualification Testing of Coatings to be Used in Nuclear Power Plants (Withdrawn 2010) |
| ASTM D 5163 : 2005 : REV A | Standard Guide for Establishing Procedures to Monitor the Performance of Service Level I Coatings in an Operating Nuclear Power Plant |
| ANSI N101.2 : 1972 | PROTECTIVE COATINGS (PAINTS) FOR LIGHT WATER NUCLEAR REACTOR CONTAINMENT FACILITIES |
| ASTM D 4537 : 2004 : REV A | Standard Guide for Establishing Procedures to Qualify and Certify Personnel Performing Coating Work Inspection in Nuclear Facilities |
| CFR 10(PTS0-199) : JAN 87 | ENERGY - NUCLEAR REGULATORY COMMISSION |
| ASTM E 1530 : 1999 | Standard Test Method for Evaluating the Resistance to Thermal Transmission of Thin Specimens of Materials by the Guarded Heat Flow Meter Technique |
| ASTM D 7230 : 2006 : R2013 | Standard Guide for Evaluating Polymeric Lining Systems for Water Immersion in Coating Service Level III Safety-Related Applications on Metal Substrates |
| ASTM D 7234 : 2005 | Standard Test Method for Pull-Off Adhesion Strength of Coatings on Concrete Using Portable Pull-Off Adhesion Testers |
| ASTM D 4541 : 2009 | Standard Test Method for Pull-Off Strength of Coatings Using Portable Adhesion Testers |
| ASTM D 3843 : 2000 : R2008 | Standard Practice for Quality Assurance for Protective Coatings Applied to Nuclear Facilities |
| ASTM D 4538 : 2005 : EDT 1 | Standard Terminology Relating to Protective Coating and Lining Work for Power Generation Facilities |
| ASTM E 1461 : 2011 | Standard Test Method for Thermal Diffusivity by the Flash Method |
| ASTM E 1461 : 2007 | Standard Test Method for Thermal Diffusivity by the Flash Method |
| ASTM D 5139 : 2012 | Standard Specification for Sample Preparation for Qualification Testing of Coatings to be Used in Nuclear Power Plants |
| ASTM D 4538 : 2005 | Standard Terminology Relating to Protective Coating and Lining Work for Power Generation Facilities |
| ASTM D 4227 : 2005 : R2017 | Standard Practice for Qualification of Coating Applicators for Application of Coatings to Concrete Surfaces |
| ASTM D 3912 : 2010 | Standard Test Method for Chemical Resistance of Coatings and Linings for Use in Nuclear Power Plants |
| ASTM D 7234 : 2012 : REDLINE | Standard Test Method for Pull-Off Adhesion Strength of Coatings on Concrete Using Portable Pull-Off Adhesion Testers |
| ASTM D 3843 : 2016 | Standard Practice for Quality Assurance for Protective Coatings Applied to Nuclear Facilities |
| ASTM D 3843 : 2000 | Standard Practice for Quality Assurance for Protective Coatings Applied to Nuclear Facilities |
| ASTM D 4541 : 2017 : REDLINE | Standard Test Method for Pull-Off Strength of Coatings Using Portable Adhesion Testers |
| ASTM D 5163 : 2016 : REDLINE | Standard Guide for Establishing a Program for Condition Assessment of Coating Service Level I Coating Systems in Nuclear Power Plants |
| ASTM D 4060 : 2007 | Standard Test Method for Abrasion Resistance of Organic Coatings by the Taber Abraser |
| ASTM D 7230 : 2006 | Standard Guide for Evaluating Polymeric Lining Systems for Water Immersion in Coating Service Level III Safety-Related Applications on Metal Substrates |
| ASTM D 7234 : 2019 | Standard Test Method for Pull-Off Adhesion Strength of Coatings on Concrete Using Portable Pull-Off Adhesion Testers |
| ASTM D 4538 : 2015 | Standard Terminology Relating to Protective Coating and Lining Work for Power Generation Facilities |
| ASTM D 4541 : 2009 : EDT 1 | Standard Test Method for Pull-Off Strength of Coatings Using Portable Adhesion Testers |
| ASTM D 3911 : 1995 | Standard Test Method for Evaluating Coatings Used in Light-Water Nuclear Power Plants at Simulated Design Basis Accident (DBA) Conditions |
| ASTM E 1530 : 2019 | Standard Test Method for Evaluating the Resistance to Thermal Transmission by the Guarded Heat Flow Meter Technique |
| ASTM D 5163 : 2008 | Standard Guide for Establishing a Program for Condition Assessment of Coating Service Level I Coating Systems in Nuclear Power Plants |
| ASTM D 4082 : 1995 | Standard Test Method for Effects of Gamma Radiation on Coatings for Use in Light-Water Nuclear Power Plants |
| ASTM D 5139 : 2019 | Standard Specification for Sample Preparation for Qualification Testing of Coatings to be Used in Nuclear Power Plants |
| ASTM D 4227 : 1999 | Standard Practice for Qualification of Coating Applicators for Application of Coatings to Concrete Surfaces |
| ASTM D 3911 : 2016 : R2021 | Standard Test Method for Evaluating Coatings Used in Light-Water Nuclear Power Plants at Simulated Design Basis Accident (DBA) Conditions |
| ASTM D 4082 : 1989 | Standard Test Method for Effects of Gamma Radiation on Coatings for Use in Light-Water Nuclear Power Plants |
| ASTM D 7491 : 2008 | Standard Guide for Management of Non-Conforming Coatings in Coating Service Level I Areas of Nuclear Power Plants |
| ASTM D 4228 : 1999 | Standard Practice for Qualification of Coating Applicators for Application of Coatings to Steel Surfaces |
| ASTM D 4537 : 2012 | Standard Guide for Establishing Procedures to Qualify and Certify Personnel Performing Coating and Lining Work Inspection in Nuclear Facilities |
| ASTM D 5139 : 2010 | Standard Specification for Sample Preparation for Qualification Testing of Coatings to be Used in Nuclear Power Plants |
| ASTM D 4541 : 2002 | Standard Test Method for Pull-Off Strength of Coatings Using Portable Adhesion Testers |
| ASTM E 1530 : 2011 | Standard Test Method for Evaluating the Resistance to Thermal Transmission of Materials by the Guarded Heat Flow Meter Technique |
| ASTM D 4537 : 2012 : R2018 | Standard Guide for Establishing Procedures to Qualify and Certify Personnel Performing Coating and Lining Work Inspection in Nuclear Facilities |
| ASTM E 1461 : 2013 : REDLINE | Standard Test Method for Thermal Diffusivity by the Flash Method |
| ASTM D 5163 : 2016 | Standard Guide for Establishing a Program for Condition Assessment of Coating Service Level I Coating Systems in Nuclear Power Plants |
| ASTM E 1530 : 2004 | Standard Test Method for Evaluating the Resistance to Thermal Transmission of Materials by the Guarded Heat Flow Meter Technique |
| ASTM D 4060 : 2001 | Standard Test Method for Abrasion Resistance of Organic Coatings by the Taber Abraser |
| ASTM D 4082 : 2002 | Standard Test Method for Effects of Gamma Radiation on Coatings for Use in Light-Water Nuclear Power Plants |
| ASTM D 7234 : 2012 | Standard Test Method for Pull-Off Adhesion Strength of Coatings on Concrete Using Portable Pull-Off Adhesion Testers |
| ASTM D 3911 : 2016 : REDLINE | Standard Test Method for Evaluating Coatings Used in Light-Water Nuclear Power Plants at Simulated Design Basis Accident (DBA) Conditions |
| ASTM D 4228 : 2005 | Standard Practice for Qualification of Coating Applicators for Application of Coatings to Steel Surfaces |
| ASTM E 1530 : 2006 | Standard Test Method for Evaluating the Resistance to Thermal Transmission of Materials by the Guarded Heat Flow Meter Technique |
| ASTM D 5163 : 2004 | Standard Guide for Establishing Procedures to Monitor the Performance of Service Level I Coatings in an Operating Nuclear Power Plant |
| ASTM D 4541 : 2017 | Standard Test Method for Pull-Off Strength of Coatings Using Portable Adhesion Testers |
| ASTM D 7491 : 2021 | Standard Guide for Management of Non-Conforming Coatings in Coating Service Level I Areas of Nuclear Power Plants |
| ASTM D 4537 : 2004 | Standard Guide for Establishing Procedures to Qualify and Certify Personnel Performing Coating Work Inspection in Nuclear Facilities |
| ASTM D 4228 : 2005 : R2017 | Standard Practice for Qualification of Coating Applicators for Application of Coatings to Steel Surfaces |
| ASTM D 3843 : 2016 : R2021 : EDT 1 | Standard Practice for Quality Assurance for Protective Coatings Applied to Nuclear Facilities |
| ASTM E 1461 : 1992 | Standard Test Method for Thermal Diffusivity of Solids by the Flash Method |
| ANSI N512 : 1974 | PROTECTIVE COATINGS (PAINTS) FOR THE NUCLEAR INDUSTRY |
| ASTM D 5163 : 1991 : R1996 | Standard Guide for Establishing Procedures to Monitor the Performance of Safety Related Coatings in an Operating Nuclear Power Plant |
| ASTM E 1530 : 2011 : R2016 | Standard Test Method for Evaluating the Resistance to Thermal Transmission of Materials by the Guarded Heat Flow Meter Technique |
| ASTM D 4082 : 2010 : R2017 | Standard Test Method for Effects of Gamma Radiation on Coatings for Use in Nuclear Power Plants |
| ASTM D 5139 : 1990 : R1996 | Standard Specification for Sample Preparation for Qualification Testing of Coatings to be Used in Nuclear Power Plants |
| ASTM D 3912 : 1995 | Standard Test Method for Chemical Resistance of Coatings Used in Light-Water Nuclear Power Plants |
| ASTM D 5163 : 2004 : REV A | Standard Guide for Establishing Procedures to Monitor the Performance of Service Level I Coatings in an Operating Nuclear Power Plant |
| ASTM D 4538 : 2021 | Standard Terminology Relating to Protective Coating and Lining Work for Power Generation Facilities |
| ASTM D 4538 : 2013 | Standard Terminology Relating to Protective Coating and Lining Work for Power Generation Facilities |
| ASTM D 4537 : 1991 : R1996 | Standard Guide for Establishing Procedures to Qualify and Certify Inspection Personnel for Coating Work in Nuclear Facilities |
| ASTM D 4227 : 2005 : R2012 | Standard Practice for Qualification of Coating Applicators for Application of Coatings to Concrete Surfaces |
| ASTM D 4228 : 2005 : R2012 | Standard Practice for Qualification of Coating Applicators for Application of Coatings to Steel Surfaces |
| ASTM D 7167 : 2012 : R2018 | Standard Guide for Establishing Procedures to Monitor the Performance of Safety-Related Coating Service Level III Lining Systems in an Operating Nuclear Power Plant |
| ASTM D 7167 : 2005 | Standard Guide for Establishing Procedures to Monitor the Performance of Safety-Related Coating Service Level III Lining Systems in an Operating Nuclear Power Plant |
| ASTM D 4060 : 1995 | Standard Test Method for Abrasion Resistance of Organic Coatings by the Taber Abraser |
| ASTM E 1461 : 2013 | Standard Test Method for Thermal Diffusivity by the Flash Method |
| ASTM E 1461 : 2001 | Standard Test Method for Thermal Diffusivity of Solids by the Flash Method |
| ASTM D 4227 : 2005 | Standard Practice for Qualification of Coating Applicators for Application of Coatings to Concrete Surfaces |
| ASTM D 3912 : 1980 : R1989 | Standard Test Method for Chemical Resistance of Coatings Used in Light-Water Nuclear Power Plants |
| ASTM D 3843 : 2016 : REDLINE | Standard Practice for Quality Assurance for Protective Coatings Applied to Nuclear Facilities |
| ASTM D 4538 : 1995 | Standard Terminology Relating to Protective Coating and Lining Work for Power Generation Facilities |
| ASTM D 3911 : 2016 | Standard Test Method for Evaluating Coatings Used in Light-Water Nuclear Power Plants at Simulated Design Basis Accident (DBA) Conditions |
| ASTM D 4541 : 1995 : EDT 1 | Standard Test Method for Pull-Off Strength of Coatings Using Portable Adhesion Testers |
| ASTM D 7167 : 2012 | Standard Guide for Establishing Procedures to Monitor the Performance of Safety-Related Coating Service Level III Lining Systems in an Operating Nuclear Power Plant |
| ASME PV CODE 11 : 2017 | BOILER AND PRESSURE VESSEL CODE - RULES FOR INSERVICE INSPECTION OF NUCLEAR POWER PLANT COMPONENTS |
| ASTM D 7491 : 2008 : R2015 | Standard Guide for Management of Non-Conforming Coatings in Coating Service Level I Areas of Nuclear Power Plants |
| ASTM D 4060 : 2014 | Standard Test Method for Abrasion Resistance of Organic Coatings by the Taber Abraser |
| ASTM D 4082 : 2010 | Standard Test Method for Effects of Gamma Radiation on Coatings for Use in Nuclear Power Plants |
| ASTM D 5163 : 2005 | Standard Guide for Establishing Procedures to Monitor the Performance of Service Level I Coatings in an Operating Nuclear Power Plant |
| ASTM D 3912 : 2010 : R2017 | Standard Test Method for Chemical Resistance of Coatings and Linings for Use in Nuclear Power Plants |
| ASTM D 4060 : 2010 | Standard Test Method for Abrasion Resistance of Organic Coatings by the Taber Abraser |
| ASTM D 3911 : 2008 | Standard Test Method for Evaluating Coatings Used in Light-Water Nuclear Power Plants at Simulated Design Basis Accident (DBA) Conditions |
| ASTM D 4538 : 2015 : REDLINE | Standard Terminology Relating to Protective Coating and Lining Work for Power Generation Facilities |
| ASTM D 3911 : 2003 | Standard Test Method for Evaluating Coatings Used in Light-Water Nuclear Power Plants at Simulated Design Basis Accident (DBA) Conditions |
| ASTM D 4060 : 2019 | Standard Test Method for Abrasion Resistance of Organic Coatings by the Taber Abraser |
£62.61
Excluding VAT
GBP
CAD
CHF
CNY
DKK
EUR
GBP
HKD
IDR
INR
JPY
KRW
MXN
NOK
NZD
SEK
SGD
USD
ZAR
Hardcopy - English
PDF - English
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.