We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
  • ASTM D 5827 : 1995

    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    Add to Watchlist
    This Standard has been added successfully to your Watchlist.
    Please visit My Watchlist to see all standards that you are watching.
    Please log in or to add this standard to your Watchlist.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    You need to be logged in to add this standard to your Watchlist.
    Please log in now or create an account to add.
    You already added this Product in the Watchlist.

    Standard Test Method for Analysis of Engine Coolant for Chloride and Other Anions by Ion Chromatography

    Available format(s):  Hardcopy, PDF

    Superseded date:  11-11-2014

    Language(s):  English

    Published date:  01-01-1995

    Publisher:  American Society for Testing and Materials

    Add to Watchlist

    Add To Cart

    Scope - (Show below) - (Hide below)

    1.1 This test method covers the chemical analysis of engine coolant for chloride ion by high-performance ion chromatography (HPIC). Several other common anions found in engine coolant can be determined in one chromatographic analysis by this test method.

    1.2 This test method is applicable to both new and used engine coolant.

    1.3 Coelution of other ions may cause interferences for any of the listed anions. In the case of unfamiliar formulations, identification verification should be performed by either or both fortification and dilution of the sample matrix with the anions of interest.

    1.4 Analysis can be performed directly by this test method without pretreatment, other than dilution, as required by the linear ranges of the equipment. Table 1 indicates several applicable anions and approximate detection limits.

    1.5 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.

    1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to its use.

    General Product Information - (Show below) - (Hide below)

    Committee D 15
    Document Type Test Method
    Publisher American Society for Testing and Materials
    Status Superseded
    Superseded By

    Standards Referenced By This Book - (Show below) - (Hide below)

    ASTM D 7388 : 2018 Standard Specification for Engine Coolant Grade 1,3-Propanediol (PDO)
    ASTM E 1177 : 2014 Standard Specification for Engine Coolant Grade Glycol
    ASTM D 7517 : 2019 Standard Specification for Fully-Formulated 1,3 Propanediol (PDO) Base Engine Coolant for Heavy-Duty Engines
    ASTM D 7640 : 2016 Standard Specification for Engine Coolant Grade Glycerin
    ASTM D 8149 : 2017 Standard Practice for Optimization, Calibration, and Validation of Ion Chromatographic Determination of Heteroatoms and Anions in Petroleum Products and Lubricants
    ASTM D 3585 : 2008 : R2013 Standard Specification for ASTM Reference Fluid for Coolant Tests
    ASTM D 7328 : 2017 Standard Test Method for Determination of Existent and Potential Inorganic Sulfate and Total Inorganic Chloride in Fuel Ethanol by Ion Chromatography Using Aqueous Sample Injection
    ASTM D 7319 : 2017 Standard Test Method for Determination of Existent and Potential Sulfate and Inorganic Chloride in Fuel Ethanol and Butanol by Direct Injection Suppressed Ion Chromatography
    ASTM D 8116 : 2018 Standard Specification for Fully-Formulated Non-Aqueous Engine Coolant for Heavy-Duty Engines (Withdrawn 2019)
    ASTM D 4985 : 2010 : R2015 Standard Specification for Low Silicate Ethylene Glycol Base Engine Coolant for Heavy Duty Engines Requiring a Pre-Charge of Supplemental Coolant Additive (SCA)
    ASTM D 7518 : 2010 : R2015 : EDT 1 Standard Specification for 1,3 Propanediol (PDO) Base Engine Coolant for Automobile and Light-Duty Service
    ASTM D 7713 : 2018 Standard Specification for Aqueous Engine Coolant Grade Glycol (53 % by Volume Nominal)
    ASTM D 2847 : 2015 Standard Practice for Testing Engine Coolants in Car and Light Truck Service
    ASTM D 3306 : 2019 Standard Specification for Glycol Base Engine Coolant for Automobile and Light-Duty Service
    ASTM D 7714 : 2011 : R2016 : EDT 1 Standard Specification for Glycerin Base Engine Coolant for Automobile and Light-Duty Service
    ASTM D 8039 : 2016 Standard Specification for Heat Transfer Fluids (HTF) for Heating and Air Conditioning (HVAC) Systems
    ASTM D 5752 : 2010 : R2017 Standard Specification for Supplemental Coolant Additives (SCAs) for Use in Precharging Coolants for Heavy-Duty Engines
    ASTM D 8085 : 2017 Standard Specification for Non-Aqueous Engine Coolant for Automobile and Light-Duty Service
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective