• There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

ASTM D 5966 : 2013

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Standard Test Method for Evaluation of Engine Oils for Roller Follower Wear in Light-Duty Diesel Engine (Withdrawn 2022)
Available format(s)

Hardcopy , PDF

Superseded date

29-04-2022

Language(s)

English

Published date

03-06-2013

1.1This engine lubricant test method is commonly referred to as the Roller Follower Wear Test. Its primary result, roller follower shaft wear in the hydraulic valve lifter assembly, has been correlated with vehicles used in stop-and-go delivery service prior to 1993. It is one of the test methods required to evaluate lubricants intended to satisfy the API CG-4 performance category. This test has also been referred to as the 6.2 L Test.

1.2The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.

1.2.1Exceptions—Where there is no direct SI equivalent, such as pipe fittings, thermocouple diameters, and NPT screw threads. Also, roller follower wear is measured in mils.

1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

1.4Table of Contents:

Section

Scope

1

Referenced Documents

2

Terminology

3

Summary of Test Method

4

Significance and Use

5

Reagents

7

 Guidelines on Substitution

7.1

Apparatus

6

Preparation of Apparatus

8

 New Engine Preparation

8.1

 Installation of Auxiliary Systems and
 Miscellaneous Components

8.2

Test Procedure

9

 Description of Test Segments and Organization
 of Test Procedure Sections

9.1

 Engine Parts Replacement

9.2

 Engine Starting Procedure

9.3

 Normal Engine Shutdown Procedure

9.4

 Emergency Shutdown Procedure

9.5

 Unscheduled Shutdown and Downtime

9.6

 New Engine Break-In

9.7

 Pretest Procedure

9.8

 Fifty-Hour Steady State Test

9.9

 Periodic Measurements

9.10

 Oil Sampling and Oil Addition Procedures

9.11

 End of Test (EOT) Procedure

9.12

Calculation and Interpretation of Test Results

10

 Environment of Parts Measurement Area

10.1

 Roller Follower Shaft Wear Measurements

10.2

 Oil Analysis

10.3

 Assessment of Test Validity

10.4

Final Test Report

11

 Reporting Calibration Test Results

11.1

 Report Forms

11.2

 Interim Non-Valid Calibration Test Summary

11.3

 Severity Adjustments

11.4

Precision and Bias

12

 Precision

12.1

 Precision Estimate

12.2

 Bias

12.3

Keywords

13

ANNEXES

Guidelines for Test Part Substitution or Modification

Annex A1

Guidelines for Units and Specification Formats

Annex A2

Detailed Specifications of Apparatus

Annex A3

Calibration

Annex A4

Final Report Forms

Annex A5

Illustrations

Annex A6

Kinematic Viscosity at 100°C Procedure for the
 Roller Follower Wear Test

Annex A7

Enhanced Thermal Gravimetric Analysis (TGA)
 Procedure for Soot Measurement

Annex A8

Sources of Materials and Information

Annex A9

APPENDIXES

PC-9 Reference Diesel Fuel Properties

Appendix X1

Diagnostic Data Review

Appendix X2


Committee
D 02
DocumentType
Test Method
Pages
19
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy
Supersedes

ASTM D 4485 : 2020 Standard Specification for Performance of Active API Service Category Engine Oils
ASTM D 6923 : 2018 Standard Test Method for Evaluation of Engine Oils in a High Speed, Single-Cylinder Diesel Engine—Caterpillar 1R Test Procedure

ASTM D 4175 : 2020 Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants
ASTM D 4175 : 2014 Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants
ASTM D 4485 : 2003 : REV A Standard Specification for Performance of Engine Oils
ASTM D 2622 : 1992 : EDT 1 Standard Test Method for Sulfur in Petroleum Products by X-Ray Spectrometry
ASTM D 4175 : 2009 : REV A : EDT 1 Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants
ASTM D 7422 : 2012 Standard Test Method for Evaluation of Diesel Engine Oils in T-12 Exhaust Gas Recirculation Diesel Engine
ASTM D 4175 : 2008 : REV B : EDT 1 Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants
ASTM D 2274 : 2010 Standard Test Method for Oxidation Stability of Distillate Fuel Oil (Accelerated Method)
ASTM D 4485 : 2006 Standard Specification for Performance of Engine Oils
ASTM D 2622 : 1987 : EDT 1 Standard Test Method for Sulfur in Petroleum Products by X-Ray Spectrometry
ASTM D 2709 : 1996 : R2011 : EDT 1 Standard Test Method for Water and Sediment in Middle Distillate Fuels by Centrifuge
ASTM D 4175 : 2005 Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants
ASTM D 2709 : 1996 : EDT 2 Standard Test Method for Water and Sediment in Middle Distillate Fuels by Centrifuge
ASTM D 4485 : 2011 : REV C Standard Specification for Performance of Active API Service Category Engine Oils
ASTM D 1319 : 1989 Standard Test Method for Hydrocarbon Types in Liquid Petroleum Products by Fluorescent Indicator Absorption
ASTM D 4175 : 2005 : EDT 2 Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants
ASTM D 1319 : 2008 Standard Test Method for Hydrocarbon Types in Liquid Petroleum Products by Fluorescent Indicator Adsorption
ASTM D 4485 : 2001 Standard Specification for Performance of Engine Oils
ASTM D 7422 : 2009 Standard Test Method for Evaluation of Diesel Engine Oils in T-12 Exhaust Gas Recirculation Diesel Engine
ASTM D 5185 : 1997 Standard Test Method for Determination of Additive Elements, Wear Metals, and Contaminants in Used Lubricating Oils and Determination of Selected Elements in Base Oils by Inductively Coupled Plasma Atomic Emission Spectrometry (ICP-AES)
ASTM D 4175 : 2015 : REV C Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants
ASTM D 4175 : 2020 : REV B Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants
ASTM D 4175 : 2017 : REV A : EDT 1 Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants
ASTM D 2274 : 2001 Standard Test Method for Oxidation Stability of Distillate Fuel Oil (Accelerated Method)
ASTM D 4485 : 2003 Standard Specification for Performance of Engine Oils
ASTM D 4052 : 1996 : R2002 : EDT 1 Standard Test Method for Density and Relative Density of Liquids by Digital Density Meter
ASTM D 4485 : 2008 Standard Specification for Performance of Engine Oils
ASTM D 2709 : 1996 : R2006 Standard Test Method for Water and Sediment in Middle Distillate Fuels by Centrifuge
ASTM D 4485 : 2015 Standard Specification for Performance of Active API Service Category Engine Oils
ASTM D 7422 : 2019 Standard Test Method for Evaluation of Diesel Engine Oils in T-12 Exhaust Gas Recirculation Diesel Engine
ASTM D 1319 : 2018 Standard Test Method for Hydrocarbon Types in Liquid Petroleum Products by Fluorescent Indicator Adsorption
ASTM D 4485 : 2005 : REV A Standard Specification for Performance of Engine Oils
ASTM D 7422 : 2016 : REV A Standard Test Method for Evaluation of Diesel Engine Oils in T-12 Exhaust Gas Recirculation Diesel Engine
ASTM D 4175 : 2008 : REV A Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants
ASTM D 4175 : 2020 : REV A Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants
ASTM D 2500 : 2016 : REV B Standard Test Method for Cloud Point of Petroleum Products and Liquid Fuels
ASTM D 4052 : 2018 : REV A Standard Test Method for Density, Relative Density, and API Gravity of Liquids by Digital Density Meter
ASTM D 1319 : 2014 Standard Test Method for Hydrocarbon Types in Liquid Petroleum Products by Fluorescent Indicator Adsorption
ASTM D 4175 : 2017 : REV B Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants
ASTM D 4175 : 2009 Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants
ASTM D 4485 : 2011 : REV A Standard Specification for Performance of Active API Service Category Engine Oils
ASTM E 29 : 2002 Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications
ASTM D 2622 : 1998 Standard Test Method for Sulfur in Petroleum Products by Wavelength Dispersive X-ray Fluorescence Spectrometry
ASTM D 2500 : 2016 : REV A Standard Test Method for Cloud Point of Petroleum Products and Liquid Fuels
ASTM D 2274 : 2003 : REV A : R2008 Standard Test Method for Oxidation Stability of Distillate Fuel Oil (Accelerated Method)
ASTM D 2500 : 2016 Standard Test Method for Cloud Point of Petroleum Products
ASTM D 1319 : 1999 Standard Test Method for Hydrocarbon Types in Liquid Petroleum Products by Fluorescent Indicator Adsorption
ASTM D 7422 : 2015 Standard Test Method for Evaluation of Diesel Engine Oils in T-12 Exhaust Gas Recirculation Diesel Engine
ASTM D 4485 : 2018 Standard Specification for Performance of Active API Service Category Engine Oils
ASTM D 5185 : 2005 Standard Test Method for Determination of Additive Elements, Wear Metals, and Contaminants in Used Lubricating Oils and Determination of Selected Elements in Base Oils by Inductively Coupled Plasma Atomic Emission Spectrometry (ICP-AES)
ASTM D 4737 : 2009 Standard Test Method for Calculated Cetane Index by Four Variable Equation
ASTM D 4175 : 2009 : REV A : EDT 4 Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants
ASTM D 4175 : 2009 : REV A : EDT 3 Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants
ASTM D 4052 : 2009 Standard Test Method for Density, Relative Density, and API Gravity of Liquids by Digital Density Meter
ASTM D 2274 : 2014 : R2019 Standard Test Method for Oxidation Stability of Distillate Fuel Oil (Accelerated Method)
ASTM D 235 : 2022 Standard Specification for Mineral Spirits (Petroleum Spirits) (Hydrocarbon Dry Cleaning Solvent)
ASTM D 5185 : 2002 Standard Test Method for Determination of Additive Elements, Wear Metals, and Contaminants in Used Lubricating Oils and Determination of Selected Elements in Base Oils by Inductively Coupled Plasma Atomic Emission Spectrometry (ICP-AES)
ASTM D 4485 : 2011 : REV B Standard Specification for Performance of Active API Service Category Engine Oils
ASTM D 2622 : 2008 Standard Test Method for Sulfur in Petroleum Products by Wavelength Dispersive X-ray Fluorescence Spectrometry
ASTM D 4485 : 2016 Standard Specification for Performance of Active API Service Category Engine Oils
ASTM D 4175 : 2018 Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants
ASTM D 4485 : 2007 Standard Specification for Performance of Engine Oils
ASTM D 7422 : 2014 : REV A Standard Test Method for Evaluation of Diesel Engine Oils in T-12 Exhaust Gas Recirculation Diesel Engine
ASTM D 4485 : 2010 Standard Specification for Performance of Engine Oils
ASTM D 5185 : 2018 Standard Test Method for Multielement Determination of Used and Unused Lubricating Oils and Base Oils by Inductively Coupled Plasma Atomic Emission Spectrometry (ICP-AES)
ASTM D 4485 : 2001 : REV A Standard Specification for Performance of Engine Oils
ASTM D 7422 : 2010 : REV A Standard Test Method for Evaluation of Diesel Engine Oils in T-12 Exhaust Gas Recirculation Diesel Engine
ASTM D 7422 : 2008 Standard Test Method for Evaluation of Diesel Engine Oils in T-12 Exhaust Gas Recirculation Diesel Engine
ASTM D 4175 : 2001 : EDT 1 Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants
ASTM D 4175 : 2020 : REV B : EDT 1 Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants
ASTM D 1319 : 2002 : REV A Standard Test Method for Hydrocarbon Types in Liquid Petroleum Products by Fluorescent Indicator Adsorption
ASTM D 2274 : 2003 Standard Test Method for Oxidation Stability of Distillate Fuel Oil (Accelerated Method)
ASTM D 7422 : 2017 : REV A Standard Test Method for Evaluation of Diesel Engine Oils in T-12 Exhaust Gas Recirculation Diesel Engine
ASTM D 2709 : 2016 Standard Test Method for Water and Sediment in Middle Distillate Fuels by Centrifuge
ASTM D 4175 : 2001 Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants
ASTM D 4175 : 2005 : EDT 1 Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants
ASTM D 2500 : 1999 Standard Test Method for Cloud Point of Petroleum Products
ASTM D 2500 : 2002 : EDT 1 Standard Test Method for Cloud Point of Petroleum Products
ASTM D 2500 : 2005 Standard Test Method for Cloud Point of Petroleum Products
ASTM D 976 : 2021 Standard Test Method for Calculated Cetane Index of Distillate Fuels
ASTM D 4175 : 2002 Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants
ASTM D 5185 : 2013 : EDT 1 Standard Test Method for Multielement Determination of Used and Unused Lubricating Oils and Base Oils by Inductively Coupled Plasma Atomic Emission Spectrometry (ICP-AES)
ASTM D 93 : 1990 : EDT 1 Standard Test Methods for Flash Point by Pensky-Martens Closed Tester
ASTM D 4485 : 2004 Standard Specification for Performance of Engine Oils
ASTM D 445 : 1988 Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and the Calculation of Dynamic Viscosity)
ASTM D 2500 : 2002 Standard Test Method for Cloud Point of Petroleum Products
ASTM D 2500 : 2011 Standard Test Method for Cloud Point of Petroleum Products
ASTM D 2500 : 2009 Standard Test Method for Cloud Point of Petroleum Products
ASTM D 4175 : 2015 Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants
ASTM D 4485 : 2000 Standard Specification for Performance of Engine Oils
ASTM D 4175 : 2002 : REV A : EDT 2 Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants
ASTM D 2500 : 2017 Standard Test Method for Cloud Point of Petroleum Products and Liquid Fuels
ASTM D 4052 : 2011 Standard Test Method for Density, Relative Density, and API Gravity of Liquids by Digital Density Meter
ASTM D 1319 : 2003 Standard Test Method for Hydrocarbon Types in Liquid Petroleum Products by Fluorescent Indicator Adsorption
ASTM D 4052 : 2016 Standard Test Method for Density, Relative Density, and API Gravity of Liquids by Digital Density Meter
ASTM D 7422 : 2013 Standard Test Method for Evaluation of Diesel Engine Oils in T-12 Exhaust Gas Recirculation Diesel Engine
ASTM D 4485 : 2015 : REV A Standard Specification for Performance of Active API Service Category Engine Oils
ASTM D 5185 : 2013 Standard Test Method for Multielement Determination of Used and Unused Lubricating Oils and Base Oils by Inductively Coupled Plasma Atomic Emission Spectrometry (ICP-AES)
ASTM D 664 : 1995 Standard Test Method for Acid Number of Petroleum Products by Potentiometric Titration
ASTM D 2622 : 2003 Standard Test Method for Sulfur in Petroleum Products by Wavelength Dispersive X-ray Fluorescence Spectrometry
ASTM D 1319 : 2010 Standard Test Method for Hydrocarbon Types in Liquid Petroleum Products by Fluorescent Indicator Adsorption
ASTM D 4175 : 2009 : REV A : EDT 5 Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants
ASTM D 4175 : 2016 : REV C Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants
ASTM D 4737 : 2009 : REV A Standard Test Method for Calculated Cetane Index by Four Variable Equation
ASTM D 4737 : 2021 Standard Test Method for Calculated Cetane Index by Four Variable Equation
ASTM D 4175 : 2015 : REV B Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants
ASTM D 7422 : 2015 : REV A Standard Test Method for Evaluation of Diesel Engine Oils in T-12 Exhaust Gas Recirculation Diesel Engine
ASTM D 4175 : 2015 : REV A Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants
ASTM D 4485 : 2006 : REV A Standard Specification for Performance of Engine Oils
ASTM D 4737 : 2010 : R2016 Standard Test Method for Calculated Cetane Index by Four Variable Equation
ASTM D 445 : 2019 : REV A Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity)
ASTM D 2274 : 1994 : R1999 : EDT 1 Standard Test Method for Oxidation Stability of Distillate Fuel Oil (Accelerated Method)
ASTM D 4175 : 2009 : REV A Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants
ASTM D 4175 : 2016 : REV B Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants
ASTM D 7422 : 2016 Standard Test Method for Evaluation of Diesel Engine Oils in T-12 Exhaust Gas Recirculation Diesel Engine
ASTM D 2500 : 2017 : REV A Standard Test Method for Cloud Point of Petroleum Products and Liquid Fuels
ASTM D 7422 : 2011 Standard Test Method for Evaluation of Diesel Engine Oils in T-12 Exhaust Gas Recirculation Diesel Engine
ASTM D 4175 : 2002 : REV A : EDT 1 Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants
ASTM D 4175 : 2008 Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants
ASTM D 7422 : 2010 Standard Test Method for Evaluation of Diesel Engine Oils in T-12 Exhaust Gas Recirculation Diesel Engine
ASTM D 4737 : 2003 Standard Test Method for Calculated Cetane Index by Four Variable Equation
ASTM D 4175 : 2002 : REV A Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants
ASTM D 4175 : 2000 : EDT 1 Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants
ASTM D 4175 : 2016 : REV A Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants
ASTM D 4052 : 1996 Standard Test Method for Density and Relative Density of Liquids by Digital Density Meter
ASTM D 235 : 2002 : R2012 Standard Specification for Mineral Spirits (Petroleum Spirits) (Hydrocarbon Dry Cleaning Solvent) (Withdrawn 2021)
ASTM D 4175 : 2019 : EDT 1 Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants
ASTM D 4485 : 2018 : REV A Standard Specification for Performance of Active API Service Category Engine Oils
ASTM D 2622 : 2010 Standard Test Method for Sulfur in Petroleum Products by Wavelength Dispersive X-ray Fluorescence Spectrometry
ASTM D 2709 : 1988 Standard Test Method for Water and Sediment in Distillate Fuels by Centrifuge
ASTM D 4485 : 2005 Standard Specification for Performance of Engine Oils
ASTM D 5185 : 2009 Standard Test Method for Determination of Additive Elements, Wear Metals, and Contaminants in Used Lubricating Oils and Determination of Selected Elements in Base Oils by Inductively Coupled Plasma Atomic Emission Spectrometry (ICP-AES)
ASTM D 93 : 2000 Standard Test Methods for Flash-Point by Pensky-Martens Closed Cup Tester
ASTM D 445 : 2001 Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (the Calculation of Dynamic Viscosity)
ASTM D 4737 : 1996 : REV A Standard Test Method for Calculated Cetane Index by Four Variable Equation
ASTM D 2622 : 2021 Standard Test Method for Sulfur in Petroleum Products by Wavelength Dispersive X-ray Fluorescence Spectrometry
ASTM D 445 : 2021 Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity)
ASTM D 7422 : 2009 : REV A Standard Test Method for Evaluation of Diesel Engine Oils in T-12 Exhaust Gas Recirculation Diesel Engine
ASTM D 4485 : 2014 Standard Specification for Performance of Active API Service Category Engine Oils
ASTM D 93 : 1985 Standard Test Method for Flash Point by Pensky-Martens Closed Tester
ASTM D 4485 : 2002 Standard Specification for Performance of Engine Oils
ASTM D 2622 : 2007 Standard Test Method for Sulfur in Petroleum Products by Wavelength Dispersive X-ray Fluorescence Spectrometry
ASTM D 4175 : 2017 : REV A Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants
ASTM D 2274 : 2003 : REV A Standard Test Method for Oxidation Stability of Distillate Fuel Oil (Accelerated Method)
ASTM D 4485 : 2005 : EDT 1 Standard Specification for Performance of Engine Oils
ASTM D 2622 : 1994 Standard Test Method for Sulfur in Petroleum Products by X-Ray Spectrometry
ASTM D 976 : 2006 : R2016 Standard Test Method for Calculated Cetane Index of Distillate Fuels
ASTM D 4175 : 2009 : REV A : EDT 2 Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants
ASTM D 2622 : 2005 Standard Test Method for Sulfur in Petroleum Products by Wavelength Dispersive X-ray Fluorescence Spectrometry
ASTM D 5185 : 2002 : EDT 1 Standard Test Method for Determination of Additive Elements, Wear Metals, and Contaminants in Used Lubricating Oils and Determination of Selected Elements in Base Oils by Inductively Coupled Plasma Atomic Emission Spectrometry (ICP-AES)
ASTM D 4737 : 2004 Standard Test Method for Calculated Cetane Index by Four Variable Equation
ASTM D 4175 : 2018 : EDT 1 Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants
ASTM D 4175 : 2016 Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants
ASTM D 1319 : 2015 Standard Test Method for Hydrocarbon Types in Liquid Petroleum Products by Fluorescent Indicator Adsorption
ASTM D 7422 : 2017 Standard Test Method for Evaluation of Diesel Engine Oils in T-12 Exhaust Gas Recirculation Diesel Engine
ASTM D 5185 : 2002 : EDT 2 Standard Test Method for Determination of Additive Elements, Wear Metals, and Contaminants in Used Lubricating Oils and Determination of Selected Elements in Base Oils by Inductively Coupled Plasma Atomic Emission Spectrometry (ICP-AES)
ASTM D 1319 : 2013 Standard Test Method for Hydrocarbon Types in Liquid Petroleum Products by Fluorescent Indicator Adsorption
ASTM D 4052 : 2015 Standard Test Method for Density, Relative Density, and API Gravity of Liquids by Digital Density Meter
ASTM D 445 : 2021 : EDT 1 Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity)
ASTM D 4175 : 2017 Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants
ASTM D 93 : 1997 Standard Test Methods for Flash-Point by Pensky-Martens Closed Cup Tester
ASTM D 4175 : 2019 Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants
ASTM D 2274 : 2001 : REV A Standard Test Method for Oxidation Stability of Distillate Fuel Oil (Accelerated Method)
ASTM D 4485 : 2009 Standard Specification for Performance of Engine Oils
ASTM D 2274 : 2014 Standard Test Method for Oxidation Stability of Distillate Fuel Oil (Accelerated Method)
ASTM D 4485 : 2019 Standard Specification for Performance of Active API Service Category Engine Oils
ASTM D 4175 : 2015 : REV B : EDT 1 Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants
ASTM D 4485 : 2010 : REV A Standard Specification for Performance of Engine Oils
ASTM D 4485 : 2011 Standard Specification for Performance of Engine Oils
ASTM D 1319 : 2019 Standard Test Method for Hydrocarbon Types in Liquid Petroleum Products by Fluorescent Indicator Adsorption
ASTM D 4052 : 2018 Standard Test Method for Density, Relative Density, and API Gravity of Liquids by Digital Density Meter
ASTM D 4737 : 2010 Standard Test Method for Calculated Cetane Index by Four Variable Equation
ASTM D 1319 : 2002 Standard Test Method for Hydrocarbon Types in Liquid Petroleum Products by Fluorescent Indicator Adsorption
ASTM D 4175 : 2008 : REV B Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants
ASTM D 2622 : 2016 Standard Test Method for Sulfur in Petroleum Products by Wavelength Dispersive X-ray Fluorescence Spectrometry
ASTM D 2709 : 1996 : R2001 : EDT 1 Standard Test Method for Water and Sediment in Middle Distillate Fuels by Centrifuge
ASTM D 7422 : 2014 Standard Test Method for Evaluation of Diesel Engine Oils in T-12 Exhaust Gas Recirculation Diesel Engine
ASTM D 4485 : 2007 : REV A Standard Specification for Performance of Engine Oils

View more information
£69.29
Excluding VAT

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.