ASTM D 618 : 2013
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
Standard Practice for Conditioning Plastics for Testing
Available format(s)
Hardcopy , PDF
Superseded date
13-08-2021
Language(s)
English
Published date
11-07-2013
In general, the physical and electrical properties of plastics are influenced by temperature and relative humidity in a manner that materially affects test results.
1.1In general, the physical and electrical properties of plastics are influenced by temperature and relative humidity in a manner that materially affects test results. In order to make reliable comparisons between different materials and between different laboratories, it is necessary to standardize the humidity conditions, as well as the temperature, to which specimens of these materials are subjected prior to and during testing. This practice defines procedures for conditioning plastics (although not necessarily to equilibrium) prior to testing, and the conditions under which they shall be tested.
1.2For some materials, it is possible that a material specification exists that requires the use of this practice, but with some procedural modifications. The material specification takes precedence over this practice. Refer to the material specification before using this practice. Table 1 in Classification D4000 lists the ASTM material specifications that currently exist.
| Committee |
D 20
|
| DocumentType |
Standard Practice
|
| Pages |
4
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| ASTM D 5575 : 2018 | Standard Classification System for Copolymers of Vinylidene Fluoride (VDF) with Other Fluorinated Monomers |
| ASTM D 1822 : 2013 | Standard Test Method for Tensile-Impact Energy to Break Plastics and Electrical Insulating Materials |
| ASTM D 7471 : 2019 | Standard Specification for CPT-Fluoropolymer Molding and Extrusion Materials |
| ASTM D 2291/D2291M : 2016 | Standard Practice for Fabrication of Ring Test Specimens for Glass-Resin Composites |
| ASTM D 2143 : 2021 | Standard Test Method for Cyclic Pressure Strength of Reinforced, Thermosetting Plastic Pipe |
| ASTM D 3294 : 2015 | Standard Specification for Polytetrafluoroethylene (PTFE) Resin Molded Sheet and Molded Basic Shapes |
| ASTM D 6691 : 2017 | Standard Test Method for Determining Aerobic Biodegradation of Plastic Materials in the Marine Environment by a Defined Microbial Consortium or Natural Sea Water Inoculum |
| ASTM D 7193 : 2017 | Standard Specification for Unsintered Pigmented Polytetrafluoroethylene (PTFE) Extruded Film or Tape |
| ASTM F 894 : 2019 | Standard Specification for Polyethylene (PE) Large Diameter Profile Wall Sewer and Drain Pipe |
| ASTM F 1533 : 2020 | Standard Specification for Deformed Polyethylene (PE) Liner |
| ASTM D 1238 : 2020 | Standard Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer |
| ASTM D 2911/D2911M : 2016 | Standard Specification for Dimensions and Tolerances for Plastic Bottles |
| ASTM F 2986 : 2012 : R2017 | Standard Specification for Corrugated Polyethylene Pipe and Fittings for Mine Leachate Applications |
| ASTM D 1201 : 2013 | Standard Specification for Thermosetting Polyester Molding Compounds |
| ASTM G 125 : 2000 : R2015 | Standard Test Method for Measuring Liquid and Solid Material Fire Limits in Gaseous Oxidants |
| ASTM D 1790 : 2021 | Standard Test Method for Brittleness Temperature of Plastic Sheeting by Impact |
| ASTM D 5117 : 2017 | Standard Test Method for Dye Penetration of Solid Fiberglass Reinforced Pultruded Stock |
| ASTM D 4068 : 2017 | Standard Specification for Chlorinated Polyethylene (CPE) Sheeting for Concealed Water-Containment Membrane |
| ASTM D 5628 : 2018 | Standard Test Method for Impact Resistance of Flat, Rigid Plastic Specimens by Means of a Falling Dart (Tup or Falling Mass) |
| ASTM D 2949 : 2018 | Standard Specification for 3.25-in. Outside Diameter Poly(Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent Pipe and Fittings |
| ASTM D 3763 : 2018 | Standard Test Method for High Speed Puncture Properties of Plastics Using Load and Displacement Sensors |
| ASTM D 4703 : 2016 | Standard Practice for Compression Molding Thermoplastic Materials into Test Specimens, Plaques, or Sheets |
| ASTM D 7194 : 2019 | Standard Specification for Aerospace Parts Machined from Polychlorotrifluoroethylene (PCTFE) |
| ASTM F 2806 : 2020 | Standard Specification for Acrylonitrile-Butadiene-Styrene (ABS) Plastic Pipe (Metric SDR-PR) |
| ASTM D 696 : 2016 | Standard Test Method for Coefficient of Linear Thermal Expansion of Plastics Between −30°C and 30°C with a Vitreous Silica Dilatometer |
| ASTM D 5485 : 2021 | Standard Test Method for Determining Corrosive Effect of Combustion Products Using the Cone Corrosimeter |
| ASTM D 4894 : 2019 | Standard Specification for Polytetrafluoroethylene (PTFE) Granular Molding and Ram Extrusion Materials |
| ASTM D 5229/D5229M : 2020 | Standard Test Method for Moisture Absorption Properties and Equilibrium Conditioning of Polymer Matrix Composite Materials |
| ASTM D 7445 : 2018 | Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Siding with Foam Plastic Backing (Backed Vinyl Siding) |
| ASTM D 2647 : 2018 | Standard Specification for Crosslinkable Ethylene Plastics |
| ASTM F 2817 : 2013 : R2019 | Standard Specification for Poly (Vinyl Chloride) (PVC) Gas Pressure Pipe and Fittings For Maintenance or Repair |
| ASTM D 2680 : 2020 | Standard Specification for Acrylonitrile-Butadiene-Styrene (ABS) and Poly(Vinyl Chloride) (PVC) Composite Sewer Piping |
| ASTM F 2658 : 2007 : R2019 | Standard Specification for Type PSM Poly(Vinyl Chloride) (PVC) SDR 51 and SDR 64 Sewer Pipe and Fittings |
| ASTM F 2969 : 2012 : R2020 | Standard Specification for Acrylonitrile-Butadiene-Styrene (ABS) IPS Dimensioned Pressure Pipe |
| ASTM F 512 : 2019 | Standard Specification for Smooth-Wall Poly(Vinyl Chloride) (PVC) Conduit and Fittings for Underground Installation |
| ASTM F 734 : 2017 | Standard Test Method for Shear Strength of Fusion Bonded Polycarbonate Aerospace Glazing Material |
| ASTM D 6289 : 2013 : R2019 | Standard Test Method for Measuring Shrinkage from Mold Dimensions of Molded Thermosetting Plastics |
| ASTM D 5721 : 2008 : R2018 | Standard Practice for Air-Oven Aging of Polyolefin Geomembranes |
| ASTM D 1779 : 1998 : R2017 | Standard Specification for Adhesive for Acoustical Materials |
| ASTM D 1776/D1776M : 2020 | Standard Practice for Conditioning and Testing Textiles |
| ASTM D 4396 : 2015 | Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) and Chlorinated Poly(Vinyl Chloride) (CPVC) Compounds for Plastic Pipe and Fittings Used in Nonpressure Applications |
| ASTM D 1204 : 2014 : R2020 | Standard Test Method for Linear Dimensional Changes of Nonrigid Thermoplastic Sheeting or Film at Elevated Temperature |
| ASTM F 2945 : 2018 | Standard Specification for Polyamide 11 Gas Pressure Pipe, Tubing, and Fittings |
| ASTM F 2854 : 2021 | Standard Specification for Push-Fit Crosslinked Polyethylene (PEX) Mechanical Fittings for Crosslinked Polyethylene (PEX) Tubing |
| ASTM D 4673 : 2016 | Standard Classification System for and Basis for Specification for Acrylonitrile–Butadiene–Styrene (ABS) Plastics and Alloys Molding and Extrusion Materials |
| ASTM D 3275 : 2018 | Standard Classification System for E-CTFE-Fluoroplastic Molding, Extrusion, and Coating Materials |
| ASTM D 7106/D7106M : 2005 : R2015 : EDT 1 | Standard Guide for Selection of Test Methods for Ethylene Propylene Diene Terpolymer (EPDM) Geomembranes |
| ASTM D 2729 : 2017 | Standard Specification for Poly(Vinyl Chloride) (PVC) Sewer Pipe and Fittings |
| ASTM D 5023 : 2015 | Standard Test Method for Plastics: Dynamic Mechanical Properties: In Flexure (Three-Point Bending) |
| ASTM D 1922 : 2015 : R2020 | Standard Test Method for Propagation Tear Resistance of Plastic Film and Thin Sheeting by Pendulum Method |
| ASTM F 3253 : 2019 | Standard Specification for Crosslinked Polyethylene (PEX) Tubing with Oxygen Barrier for Hot- and Cold-Water Hydronic Distribution Systems |
| ASTM D 3748 : 2014 : R2019 | Standard Practice for Evaluating High-Density Rigid Cellular Plastics |
| ASTM D 6272 : 2017 : EDT 1 | Standard Test Method for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials by Four-Point Bending |
| ASTM D 2992 : 2018 | Standard Practice for Obtaining Hydrostatic or Pressure Design Basis for “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe and Fittings |
| ASTM F 964 : 2013 : R2019 | Standard Specification for Rigid Poly (Vinyl Chloride) (PVC) Exterior Profiles Used for Fencing and Railing |
| ASTM D 5319 : 2017 | Standard Specification for Glass-Fiber Reinforced Polyester Wall and Ceiling Panels |
| ASTM E 2769 : 2018 | Standard Test Method for Elastic Modulus by Thermomechanical Analysis Using Three-Point Bending and Controlled Rate of Loading |
| ASTM D 2235 : 2004 : R2016 | Standard Specification for Solvent Cement for Acrylonitrile-Butadiene-Styrene (ABS) Plastic Pipe and Fittings |
| ASTM F 2433 : 2005 : R2018 | Standard Test Method for Determining Thermoplastic Pipe Wall Stiffness |
| ASTM D 5748 : 1995 : R2019 | Standard Test Method for Protrusion Puncture Resistance of Stretch Wrap Film |
| ASTM F 736 : 2017 | Standard Test Method for Impact Resistance of Monolithic Polycarbonate Sheet by Means of a Falling Weight |
| ASTM F 3034 : 2015 : R2020 | Standard Specification for Billets made by Winding Molten Extruded Stress-Rated High Density Polyethylene (HDPE) |
| ASTM D 2671 : 2021 | Standard Test Methods for Heat-Shrinkable Tubing for Electrical Use |
| ASTM D 4883 : 2018 | Standard Test Method for Density of Polyethylene by the Ultrasound Technique |
| ASTM D 6867 : 2019 | Standard Specification for Perfluoroalkoxy (PFA)-Fluoropolymer Tubing |
| ASTM D 1043 : 2016 | Standard Test Method for Stiffness Properties of Plastics as a Function of Temperature by Means of a Torsion Test |
| ASTM F 2686 : 2014 | Standard Specification for Glass Fiber Reinforced Thermoplastic Pipe (Withdrawn 2023) |
| ASTM D 3034 : 2016 | Standard Specification for Type PSM Poly(Vinyl Chloride) (PVC) Sewer Pipe and Fittings |
| ASTM D 2240 : 2015 : EDT 1 | Standard Test Method for Rubber Property—Durometer Hardness |
| ASTM D 6434 : 2012 : R2018 | Standard Guide for the Selection of Test Methods for Flexible Polypropylene Geomembranes |
| ASTM D 1622 : 2020 | Standard Test Method for Apparent Density of Rigid Cellular Plastics |
| ASTM D 4762 : 2018 | Standard Guide for Testing Polymer Matrix Composite Materials |
| ASTM F 891 : 2016 | Standard Specification for Coextruded Poly(Vinyl Chloride) (PVC) Plastic Pipe With a Cellular Core |
| ASTM D 8136 : 2017 | Standard Test Method for Determining Plastic Film Thickness and Thickness Variability Using a Non-Contact Capacitance Thickness Gauge |
| ASTM F 2160 : 2016 | Standard Specification for Solid Wall High Density Polyethylene (HDPE) Conduit Based on Controlled Outside Diameter (OD) |
| ASTM E 906/E906M : 2017 | Standard Test Method for Heat and Visible Smoke Release Rates for Materials and Products Using a Thermopile Method |
| ASTM D 2444 : 2021 | Standard Practice for Determination of the Impact Resistance of Thermoplastic Pipe and Fittings by Means of a Tup (Falling Weight) |
| ASTM F 2600 : 2009 : R2018 | Standard Specification for Electrofusion Type Polyamide-11 Fittings for Outside Diameter Controlled Polyamide-11 Pipe and Tubing |
| ASTM D 149 : 2020 | Standard Test Method for Dielectric Breakdown Voltage and Dielectric Strength of Solid Electrical Insulating Materials at Commercial Power Frequencies |
| ASTM D 5329 : 2020 | Standard Test Methods for Sealants and Fillers, Hot-Applied, for Joints and Cracks in Asphalt Pavements and Portland Cement Concrete Pavements |
| ASTM D 1868 : 2020 | Standard Test Method for Detection and Measurement of Partial Discharge (Corona) Pulses in Evaluation of Insulation Systems |
| ASTM D 150 : 2018 | Standard Test Methods for AC Loss Characteristics and Permittivity (Dielectric Constant) of Solid Electrical Insulation |
| ASTM D 3678 : 2019 | Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Interior-Profile Extrusions |
| ASTM F 2618 : 2021 | Standard Specification for Chlorinated Poly (Vinyl Chloride) (CPVC) Pipe and Fittings for Chemical Waste Drainage Systems |
| ASTM D 6358 : 2019 : EDT 1 | Standard Classification System and Basis for Specification for Poly (Phenylene Sulfide) (PPS) Injection Molding, Extrusion and Blow Molding Materials Using ISO Methods |
| ASTM D 2343 : 2017 | Standard Test Method for Tensile Properties of Glass Fiber Strands, Yarns, and Rovings Used in Reinforced Plastics |
| ASTM D 4272/D4272M : 2015 | Standard Test Method for Total Energy Impact of Plastic Films by Dart Drop |
| ASTM F 2306/F2306M : 2020 | Standard Specification for 12 to 60 in. [300 to 1500 mm] Annular Corrugated Profile-Wall Polyethylene (PE) Pipe and Fittings for Gravity-Flow Storm Sewer and Subsurface Drainage Applications |
| ASTM D 2843 : 2019 | Standard Test Method for Density of Smoke from the Burning or Decomposition of Plastics |
| ASTM D 6712 : 2017 | Standard Specification for Ultra-High-Molecular-Weight Polyethylene (UHMW-PE) Solid Plastic Shapes |
| ASTM D 1430 : 2017 | Standard Classification System for Polychlorotrifluoroethylene (PCTFE) Plastics |
| ASTM D 3916 : 2008 : R2016 | Standard Test Method for Tensile Properties of Pultruded Glass-Fiber-Reinforced<brk /> Plastic Rod |
| ASTM D 5930 : 2017 | Standard Test Method for Thermal Conductivity of Plastics by Means of a Transient Line-Source Technique |
| ASTM D 5685 : 2019 | Standard Specification for “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Pressure Pipe Fittings |
| ASTM D 7475 : 2020 | Standard Test Method for Determining the Aerobic Degradation and Anaerobic Biodegradation of Plastic Materials under Accelerated Bioreactor Landfill Conditions |
| ASTM F 2928 : 2018 | Standard Practice for Specimens and Testing Conditions for Testing Polyethylene (PE) Pipe Butt Fusions Using Tensile and Hydrostatic Test Methods |
| ASTM D 6338 : 2017 | Standard Classification System for Highly Crosslinked Thermoplastic Vulcanizates (HCTPV) Based on ASTM Standard Test Methods |
| ASTM F 2763/F2763M : 2016 : R2021 : EDT 1 | Standard Specification for 12 to 60 in. [300 to 1500 mm] Dual and Triple Profile-Wall Polyethylene (PE) Pipe and Fittings for Sanitary Sewer Applications |
| ASTM D 2683 : 2020 | Standard Specification for Socket-Type Polyethylene Fittings for Outside Diameter-Controlled Polyethylene Pipe and Tubing |
| ASTM D 746 : 2020 | Standard Test Method for Brittleness Temperature of Plastics and Elastomers by Impact |
| ASTM D 6394 : 2021 : REV A | Standard Classification System for and Basis for Specification for Sulfone Plastics (SP) |
| ASTM D 705 : 1999 : R2020 | Standard Specification for Urea-Formaldehyde Molding Compounds |
| ASTM F 438 : 2017 | Standard Specification for Socket-Type Chlorinated Poly(Vinyl Chloride) (CPVC) Plastic Pipe Fittings, Schedule 40 |
| ASTM D 1879 : 2006 : R2014 | Standard Practice for Exposure of Adhesive Specimens to Ionizing Radiation |
| ASTM F 2968/F2968M : 2021 | Standard Specification for Crosslinked Polyethylene (PEX) Pipe for Gas Distribution Applications |
| ASTM D 3030 : 2017 | Standard Test Method for Volatile Matter (Including Water) of Vinyl Chloride Resins |
| ASTM F 1483 : 2017 | Standard Specification for Oriented Poly(Vinyl Chloride), PVCO, Pressure Pipe |
| ASTM D 4802 : 2016 | Standard Specification for Poly(Methyl Methacrylate) Acrylic Plastic Sheet |
| ASTM D 4895 : 2018 | Standard Specification for Polytetrafluoroethylene (PTFE) Resin Produced From Dispersion |
| ASTM F 3219 : 2019 | Standard Specification for 3 to 30 in. (75 To 750 mm) Polypropylene (PP) Corrugated Single Wall Pipe and Fittings |
| ASTM D 6778 : 2020 | Standard Classification System and Basis for Specification for Polyoxymethylene Molding and Extrusion Materials (POM) |
| ASTM F 2418 : 2019 | Standard Specification for Polypropylene (PP) Corrugated Wall Stormwater Collection Chambers |
| ASTM D 706 : 2020 | Standard Classification System and Basis for Specifications for Cellulose Acetate Molding and Extrusion Compounds (CA) |
| ASTM D 4335 : 2018 | Standard Practice for Determination of Component Retention of a Mechanical Pump Dispenser |
| ASTM D 5138 : 2016 | Standard Classification System and Basis for Specification for Liquid Crystal Polymers Molding and Extrusion Materials (LCP) |
| ASTM D 882 : 2018 | Standard Test Method for Tensile Properties of Thin Plastic Sheeting |
| ASTM D 4801 : 2008 : R2016 | Standard Specification for Polyethylene Sheeting in Thickness of 0.25 mm (0.010 in.) and Greater |
| ASTM D 785 : 2008 : R2015 | Standard Test Method for Rockwell Hardness of Plastics and Electrical Insulating Materials |
| ASTM F 2922 : 2013 : R2018 | Standard Specification for Polyethylene (PE) Corrugated Wall Stormwater Collection Chambers |
| ASTM D 6108 : 2019 | Standard Test Method for Compressive Properties of Plastic Lumber and Shapes |
| ASTM D 3159 : 2020 | Standard Specification for Modified ETFE Fluoropolymer Molding and Extrusion Materials |
| ASTM D 7791 : 2017 | Standard Test Method for Uniaxial Fatigue Properties of Plastics |
| ASTM D 732 : 2017 | Standard Test Method for Shear Strength of Plastics by Punch Tool |
| ASTM F 1974 : 2009 : R2020 | Standard Specification for Metal Insert Fittings for Polyethylene/Aluminum/Polyethylene and Crosslinked Polyethylene/Aluminum/Crosslinked Polyethylene Composite Pressure Pipe |
| ASTM F 2720/F2720M : 2020 | Standard Specification for Glass Fiber Reinforced Polyethylene (PE-GF) Spiral Wound Large Diameter Pipe |
| ASTM F 1866 : 2018 | Standard Specification for Poly (Vinyl Chloride) (PVC) Plastic Schedule 40 Drainage and DWV Fabricated Fittings |
| ASTM D 1248 : 2016 | Standard Specification for Polyethylene Plastics Extrusion Materials for Wire and Cable |
| ASTM D 1593 : 2019 | Standard Specification for Nonrigid Vinyl Chloride Plastic Film and Sheeting |
| ASTM D 4611 : 2016 | Standard Test Method for Specific Heat of Rock and Soil |
| ASTM D 2665 : 2020 | Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent Pipe and Fittings |
| ASTM F 2788/F2788M : 2021 | Standard Specification for Metric and Inch-sized Crosslinked Polyethylene (PEX) Pipe |
| ASTM D 6713 : 2019 | Standard Specification for Extruded and Compression Molded Shapes Made from Poly(Vinylidene Fluoride) (PVDF) |
| ASTM D 3122 : 2015 | Standard Specification for Solvent Cements for Styrene-Rubber (SR) Plastic Pipe and Fittings |
| ASTM D 6068 : 2010 : R2018 | Standard Test Method for Determining <emph type="bdit">J-R </emph>Curves of Plastic Materials |
| ASTM D 4349 : 2016 | Classification System and Basis for Specification for Polyphenylene Ether (PPE) Materials |
| ASTM D 4216 : 2017 | Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) and Related PVC and Chlorinated Poly(Vinyl Chloride) (CPVC) Building Products Compounds |
| ASTM D 707 : 2015 | Standard Classification System and Basis for Specification for Cellulose Acetate Butyrate Molding and Extrusion Compounds (CAB) |
| ASTM F 1488 : 2014 : R2019 | Standard Specification for Coextruded Composite Pipe |
| ASTM D 2583 : 2013 : REV A | Standard Test Method for Indentation Hardness of Rigid Plastics by Means of a Barcol Impressor (Withdrawn 2022) |
| ASTM D 1693 : 2015 : EDT 1 | Standard Test Method for Environmental Stress-Cracking of Ethylene Plastics |
| ASTM D 4812 : 2019 | Standard Test Method for Unnotched Cantilever Beam Impact Resistance of Plastics |
| ASTM F 1871 : 2020 | Standard Specification for Folded/Formed Poly (Vinyl Chloride) Pipe Type A for Existing Sewer and Conduit Rehabilitation |
| ASTM F 439 : 2019 | Standard Specification for Chlorinated Poly (Vinyl Chloride) (CPVC) Plastic Pipe Fittings, Schedule 80 |
| ASTM D 4397 : 2016 | Standard Specification for Polyethylene Sheeting for Construction, Industrial, and Agricultural Applications |
| ASTM F 441/F441M : 2020 | Standard Specification for Chlorinated Poly(Vinyl Chloride) (CPVC) Plastic Pipe, Schedules 40 and 80 |
| ASTM F 1282 : 2017 | Standard Specification for Polyethylene/Aluminum/Polyethylene (PE-AL-PE) Composite Pressure Pipe |
| ASTM D 953 : 2019 | Standard Test Method for Pin-Bearing Strength of Plastics |
| ASTM D 3841 : 2021 | Standard Specification for Glass-Fiber-Reinforced Polyester Plastic Panels |
| ASTM D 3222 : 2020 | Standard Specification for Unmodified Poly(Vinylidene Fluoride) (PVDF) Molding Extrusion and Coating Materials |
| ASTM F 2863 : 2011 : R2016 | Standard Specification for Central Vacuum Hose Inlet Valve Socket Dimensions |
| ASTM D 5436 : 2015 : R2020 | Standard Specification for Cast Poly(Methyl Methacrylate) Plastic Rods, Tubes, and Shapes |
| ASTM D 4476/D4476M : 2014 | Standard Test Method for Flexural Properties of Fiber Reinforced Pultruded Plastic Rods (Withdrawn 2022) |
| ASTM D 5946 : 2017 | Standard Test Method for Corona-Treated Polymer Films Using Water Contact Angle Measurements |
| ASTM D 5024 : 2015 | Standard Test Method for Plastics: Dynamic Mechanical Properties: In Compression |
| ASTM D 2105 : 2001 : R2019 | Standard Test Method for Longitudinal Tensile Properties of “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe and Tube |
| ASTM D 1494 : 2017 | Standard Test Method for Diffuse Light Transmission Factor of Reinforced Plastics Panels |
| ASTM D 2287 : 2019 | Standard Classification System and Basis for Specification for Nonrigid Vinyl Chloride Polymer and Copolymer Molding and Extrusion Compounds |
| ASTM D 952 : 2015 | Standard Test Method for Bond or Cohesive Strength of Sheet Plastics and Electrical Insulating Materials |
| ASTM F 2829/F2829M : 2021 | Standard Specification for Metric- and Inch-Sized Fittings for Crosslinked Polyethylene (PEX) Pipe |
| ASTM F 2435 : 2015 | Standard Specification for Steel Reinforced Polyethylene (PE) Corrugated Pipe |
| ASTM D 3296 : 2014 : REV A : R2019 | Standard Specification for FEP-Fluorocarbon Tube |
| ASTM F 2764/F2764M : 2019 | Standard Specification for 6 to 60 in. [150 to 1500 mm] Polypropylene (PP) Corrugated Double and Triple Wall Pipe and Fittings for Non-Pressure Sanitary Sewer Applications |
| ASTM D 1003 : 2021 | Standard Test Method for Haze and Luminous Transmittance of Transparent Plastics |
| ASTM G 74 : 2013 | Standard Test Method for Ignition Sensitivity of Nonmetallic Materials and Components by Gaseous Fluid Impact |
| ASTM D 6585 : 2017 | Standard Specification for Unsintered Polytetrafluoroethylene (PTFE) Extruded Film or Tape |
| ASTM D 1894 : 2014 | Standard Test Method for Static and Kinetic Coefficients of Friction of Plastic Film and Sheeting (Withdrawn 2023) |
| ASTM D 8033 : 2016 | Standard Classification System for Poly(Ether Ether Ketone) (PEEK) Molding and Extrusion Materials |
| ASTM D 2103 : 2015 | Standard Specification for Polyethylene Film and Sheeting |
| ASTM D 1998 : 2015 | Standard Specification for Polyethylene Upright Storage Tanks |
| ASTM F 1504 : 2014 : R2021 : EDT 1 | Standard Specification for Folded Poly(Vinyl Chloride) (PVC) Pipe for Existing Sewer and Conduit Rehabilitation |
| ASTM F 1901 : 2016 | Standard Specification for Polyethylene (PE) Pipe and Fittings for Roof Drain Systems |
| ASTM D 2275 : 2014 | Standard Test Method for Voltage Endurance of Solid Electrical Insulating Materials Subjected to Partial Discharges (Corona) on the Surface |
| ASTM D 6109 : 2019 | Standard Test Methods for Flexural Properties of Unreinforced and Reinforced Plastic Lumber and Related Products |
| ASTM D 788 : 2016 | Standard Classification System for Poly(Methyl Methacrylate) (PMMA) Molding and Extrusion Compounds |
| ASTM D 1004 : 2021 | Standard Test Method for Tear Resistance (Graves Tear) of Plastic Film and Sheeting |
| ASTM D 7472 : 2019 | Standard Specification for EFEP-Fluoropolymer Molding and Extrusion Materials |
| ASTM D 7792/D7792M : 2015 | Standard Practice for Freeze/Thaw Conditioning of Pultruded Fiber Reinforced Polymer (FRP) Composites Used in Structural Designs |
| ASTM D 7027 : 2020 | Standard Test Method for Evaluation of Scratch Resistance of Polymeric Coatings and Plastics Using an Instrumented Scratch Machine |
| ASTM F 1735 : 2021 | Standard Specification for Poly (Vinyl Chloride) (PVC) Profile Strip for PVC Liners for Rehabilitation of Existing Man-Entry Sewers and Conduits |
| ASTM F 437 : 2021 | Standard Specification for Threaded Chlorinated Poly(Vinyl Chloride) (CPVC) Plastic Pipe Fittings, Schedule 80 |
| ASTM D 3012 : 2019 | Standard Test Method for Thermal-Oxidative Stability of Polypropylene Using a Specimen Rotator Within an Oven |
| ASTM D 7992/D7992M : 2015 | Standard Practice for Elevated Temperature and Moisture Conditioning of Pultruded Fiber Reinforced Polymer (FRP) Composites Used in Structural Designs |
| ASTM F 2623 : 2019 | Standard Specification for Polyethylene of Raised Temperature (PE-RT) Systems for Non-Potable Water Applications |
| ASTM D 543 : 2020 | Standard Practices for Evaluating the Resistance of Plastics to Chemical Reagents |
| ASTM D 5948 : 2005 : R2020 | Standard Specification for Molding Compounds, Thermosetting |
| ASTM D 5526 : 2018 | Standard Test Method for Determining Anaerobic Biodegradation of Plastic Materials Under Accelerated Landfill Conditions |
| ASTM F 1306 : 2021 | Standard Test Method for Slow Rate Penetration Resistance of Flexible Barrier Films and Laminates |
| ASTM F 1336 : 2020 | Standard Specification for Poly(Vinyl Chloride) (PVC) Gasketed Sewer Fittings |
| ASTM D 1203 : 2021 | Standard Test Methods for Volatile Loss from Plastics Using Activated Carbon Methods |
| ASTM D 1932 : 2019 | Standard Test Method for Thermal Endurance of Flexible Electrical Insulating Varnishes |
| ASTM D 4969 : 2017 | Standard Specification for Polytetrafluoroethylene–(PTFE) Coated Glass Fabric |
| ASTM D 6835 : 2017 | Standard Classification System for Thermoplastic Elastomer-Ether-Ester Molding and Extrusion Materials (TEEE) |
| ASTM D 2582 : 2021 | Standard Test Method for Puncture-Propagation Tear Resistance of Plastic Film and Thin Sheeting |
| ASTM F 3506 : 2021 : EDT 1 | Standard Specification for Standard Specification for Polyethylene of Raised Temperature/Aluminum/Polyethylene of Raised Temperature (PE-RT/AL/PE-RT) Composite Pressure Pipe based on Inner Diameter (ID) for use in Air Conditioning and Refrigeration Line Set Systems |
| ASTM D 2228 : 2004 : R2019 | Standard Test Method for Rubber Property—Relative Abrasion Resistance by Pico Abrader Method |
| ASTM F 679 : 2016 | Standard Specification for Poly(Vinyl Chloride) (PVC) Large-Diameter Plastic Gravity Sewer Pipe and Fittings |
| ASTM F 1803 : 2015 : R2019 | Standard Specification for Poly (Vinyl Chloride)(PVC) Closed Profile Gravity Pipe and Fittings Based on Controlled Inside Diameter |
| ASTM F 3131 : 2014 | Standard Specification for Epoxy / Cotton Raw Materials for the Use in Bearing Cages |
| ASTM D 4551 : 2017 | Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Flexible Concealed Water-Containment Membrane |
| ASTM F 2769 : 2018 | Standard Specification for Polyethylene of Raised Temperature (PE-RT) Plastic Hot and Cold-Water Tubing and Distribution Systems |
| ASTM D 4635 : 2016 | Standard Specification for Plastic Films Made from Low-Density Polyethylene and Linear Low-Density Polyethylene for General Use and Packaging Applications |
| ASTM F 1362 : 2018 | Standard Test Method for Shear Strength and Shear Modulus of Aerospace Glazing Interlayer Materials |
| ASTM D 1712 : 2009 : R2020 | Standard Practice for Resistance of Plastics to Sulfide Staining |
| ASTM D 2672 : 2020 : EDT 1 | Standard Specification for Joints for IPS PVC Pipe Using Solvent Cement |
| ASTM D 2148 : 2019 : EDT 1 | Standard Test Methods for Bondable Silicone Rubber Tapes Used for Electrical Insulation |
| ASTM F 2929 : 2017 | Standard Specification for Crosslinked Polyethylene (PEX) Tubing of 0.070 in. Wall and Fittings for Radiant Heating Systems up to 75 psig |
| ASTM D 6113 : 2021 | Standard Test Method for Using Cone Calorimeter to Determine Fire-Test-Response Characteristics of Insulating Materials Contained in Electrical or Optical Fiber Cables |
| ASTM F 3346 : 2019 | Standard Specification for Polyethylene of Raised Temperature/Aluminum/Polyethylene of Raised Temperature (PERT/AL/PE-RT) Composite Pressure Pipe |
| ASTM D 1636 : 2013 | Standard Specification for Allyl Molding Compounds |
| ASTM F 949 : 2020 | Standard Specification for Poly(Vinyl Chloride) (PVC) Corrugated Sewer Pipe With a Smooth Interior and Fittings |
| ASTM D 3965 : 2016 | Standard Classification System and Basis for Specifications for Rigid Acrylonitrile-Butadiene-Styrene (ABS) Materials for Pipe and Fittings |
| ASTM D 2852 : 2016 | Standard Specification for Styrene-Rubber (SR) Plastic Drain Pipe and Fittings (Withdrawn 2022) |
| ASTM F 2984 : 2013 : R2019 | Standard Specification for Segmental Panel System for the Grout-in-Place-Liner (GIPL) Rehabilitation Method of Existing Man-Entry Size Sewers, Culverts, and Conduits |
| ASTM D 5418 : 2015 | Standard Test Method for Plastics: Dynamic Mechanical Properties: In Flexure (Dual Cantilever Beam) |
| ASTM F 2807 : 2013 : R2018 | Standard Specification for Multilayer Polyethylene-Polyamide (PE-PA) Pipe for Pressure Piping Applications |
| ASTM D 695 : 2015 | Standard Test Method for Compressive Properties of Rigid Plastics |
| ASTM D 4477 : 2016 | Standard Specification for Rigid (Unplasticized) Poly(Vinyl Chloride) (PVC) Soffit |
| ASTM D 2659 : 2016 | Standard Test Method for Column Crush Properties of Blown Thermoplastic Containers |
| ASTM D 5288 : 2014 | Standard Test Method for Determining Tracking Index of Electrical Insulating Materials Using Various Electrode Materials (Excluding Platinum) |
| ASTM D 3308 : 2012 : R2017 | Standard Specification for PTFE Resin Skived Tape |
| ASTM F 3128 : 2019 | Standard Specification for Poly(Vinyl Chloride) (PVC) Schedule 40 Drain, Waste, and Vent Pipe with a Cellular Core |
| ASTM G 151 : 2019 | Standard Practice for Exposing Nonmetallic Materials in Accelerated Test Devices that Use Laboratory Light Sources |
| ASTM D 5947 : 2018 | Standard Test Methods for Physical Dimensions of Solid Plastics Specimens |
| ASTM G 176 : 2003 : R2017 | Standard Test Method for Ranking Resistance of Plastics to Sliding Wear Using Block-on-Ring Wear Test—Cumulative Wear Method |
| ASTM D 6098 : 2016 | Standard Classification System and Basis for Specification for Extruded and Compression Molded Shapes Made from Polycarbonate (PC) |
| ASTM D 6325 : 1998 : R2019 | Standard Test Method for Determining Open Assembly Time of Carpet Mastic Adhesives |
| ASTM D 2513 : 2020 | Standard Specification for Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 2609 : 2021 | Standard Specification for Plastic Insert Fittings for Polyethylene (PE) Plastic Pipe |
| ASTM F 119 : 1982 : R2015 | Standard Test Method for Rate of Grease Penetration of Flexible Barrier Materials (Rapid Method) |
| ASTM F 1412 : 2016 | Standard Specification for Polyolefin Pipe and Fittings for Corrosive Waste Drainage Systems |
| ASTM F 480 : 2014 | Standard Specification for Thermoplastic Well Casing Pipe and Couplings Made in Standard Dimension Ratios (SDR), SCH 40 and SCH 80 |
| ASTM F 2881/F2881M : 2021 | Standard Specification for 12 to 60 in. [300 to 1500 mm] Polypropylene (PP) Dual Wall Pipe and Fittings for Non-Pressure Storm Sewer Applications |
| ASTM D 6150 : 2016 | Standard Test Method for Estimating Processing Losses of Plastisols and Organosols Due to Volatility |
| ASTM D 2737 : 2012 : REV A : R2020 | Standard Specification for Polyethylene (PE) Plastic Tubing |
| ASTM D 1039 : 2016 | Standard Test Methods for Glass-Bonded Mica Used as Electrical Insulation |
| ASTM D 2152 : 2017 | Standard Test Method for Adequacy of Fusion of Extruded Poly(Vinyl Chloride) (PVC) Pipe and Molded Fittings by Acetone Immersion |
| ASTM D 3295 : 2020 | Standard Specification for PTFE Tubing, Miniature Beading and Spiral Cut Tubing |
| ASTM F 1673 : 2010 : R2016 | Standard Specification for Polyvinylidene Fluoride (PVDF) Corrosive Waste Drainage Systems |
| ASTM G 137 : 1997 : R2017 | Standard Test Method for Ranking Resistance of Plastic Materials to Sliding Wear Using a Block-On-Ring Configuration |
| ASTM D 3420 : 2021 | Standard Test Method for Pendulum Impact Resistance of Plastic Film |
| ASTM D 4093 : 1995 : R2014 | Standard Test Method for Photoelastic Measurements of Birefringence and Residual Strains in Transparent or Translucent Plastic Materials |
| ASTM D 3485 : 2015 | Standard Specification for Coilable High Density Polyethylene (HDPE) Cable in Conduit (CIC) |
| ASTM D 1938 : 2019 | Standard Test Method for Tear-Propagation Resistance (Trouser Tear) of Plastic Film and Thin Sheeting by a Single-Tear Method |
| ASTM D 4226 : 2019 : EDT 1 | Standard Test Methods for Impact Resistance of Rigid Poly(Vinyl Chloride) (PVC) Building Products |
| ASTM D 4496 : 2021 | Standard Test Method for D-C Resistance or Conductance of Moderately Conductive Materials |
| ASTM D 4101 : 2017 : EDT 1 | Standard Classification System and Basis for Specification for Polypropylene Injection and Extrusion Materials |
| ASTM D 7211 : 2013 : R2018 | Standard Specification for Parts Machined from Polychlorotrifluoroethylene (PCTFE) and Intended for General Use |
| ASTM F 2158 : 2008 : R2016 | Standard Specification for Residential Central-Vacuum Tube and Fittings |
| ASTM D 4097 : 2019 | Standard Specification for Contact-Molded Glass-Fiber-Reinforced Thermoset Resin Corrosion-Resistant Tanks |
| ASTM D 787 : 2018 | Standard Specification for Ethyl Cellulose Molding and Extrusion Compounds |
| ASTM D 2632 : 2015 : R2019 | Standard Test Method for Rubber Property—Resilience by Vertical Rebound |
| ASTM F 758 : 2014 : R2019 | Standard Specification for Smooth-Wall Poly(Vinyl Chloride) (PVC) Plastic Underdrain Systems for Highway, Airport, and Similar Drainage |
| ASTM D 6110 : 2018 | Standard Test Method for Determining the Charpy Impact Resistance of Notched Specimens of Plastics |
| ASTM D 4000 : 2020 | Standard Classification System for Specifying Plastic Materials |
| ASTM D 907 : 2015 | Standard Terminology of Adhesives |
| ASTM D 1562 : 2015 | Standard Classification System and Basis for Specification for Cellulose Acetate Propionate Molding and Extrusion Compounds (CAP) |
| ASTM D 2838 : 2018 | Standard Test Method for Shrink Tension and Orientation Release Stress of Plastic Film and Thin Sheeting |
| ASTM D 2734 : 2016 | Standard Test Methods for Void Content of Reinforced Plastics |
| ASTM F 1957 : 1999 : R2017 | Standard Test Method for Composite Foam Hardness-Durometer Hardness |
| ASTM D 5419 : 2014 : REV A | Standard Test Method for Environmental Stress Crack Resistance (ESCR) of Threaded Plastic Closures |
| ASTM D 7705/D7705M : 2012 : R2019 | Standard Test Method for Alkali Resistance of Fiber Reinforced Polymer (FRP) Matrix Composite Bars used in Concrete Construction |
| ASTM D 2467 : 2020 | Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Pipe Fittings, Schedule 80 |
| ASTM D 4976 : 2012 : REV A : R2020 | Standard Specification for Polyethylene Plastics Molding and Extrusion Materials |
| ASTM D 2863 : 2019 | Standard Test Method for Measuring the Minimum Oxygen Concentration to Support Candle-Like Combustion of Plastics (Oxygen Index) |
| ASTM F 2390 : 2012 : R2017 | Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent (DWV) Pipe and Fittings Having Post-Industrial Recycle Content |
| ASTM D 3914 : 2002 : R2016 | Standard Test Method for In-Plane Shear Strength of Pultruded Glass-Reinforced Plastic Rod |
| ASTM F 1365 : 1991 : R2018 | Standard Test Method for Water Infiltration Resistance of Plastic Underground Conduit Joints Which Use Flexible Elastomeric Seals |
| ASTM D 1785 : 2021 | Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Pipe, Schedules 40, 80, and 120 |
| ASTM D 5422 : 2017 | Standard Test Method for Measurement of Properties of Thermoplastic Materials by Screw-Extrusion Capillary Rheometer |
| ASTM D 6100 : 2017 | Standard Specification for Extruded, Compression Molded and Injection Molded Polyoxymethylene Shapes (POM) |
| ASTM D 3826 : 2018 | Standard Practice for Determining Degradation End Point in Degradable Polyethylene and Polypropylene Using a Tensile Test |
| ASTM D 5740 : 2018 | Standard Guide for Writing Material Standards in the Classification D4000 Format |
| ASTM G 21 : 2015 : R2021 : EDT 1 | Standard Practice for Determining Resistance of Synthetic Polymeric Materials to Fungi |
| ASTM F 442/F442M : 2020 | Standard Specification for Chlorinated Poly(Vinyl Chloride) (CPVC) Plastic Pipe (SDR–PR) |
| ASTM D 1709 : 2016 : REV A : EDT 1 | Standard Test Methods for Impact Resistance of Plastic Film by the Free-Falling Dart Method |
| ASTM F 1864 : 2021 | Standard Test Method for Dust Erosion Resistance of Optical and Infrared Transparent Materials and Coatings |
| ASTM D 5026 : 2015 | Standard Test Method for Plastics: Dynamic Mechanical Properties: In Tension |
| ASTM D 8366 : 2021 | Standard Specification for Extruded and Compression Molded Shapes Made from Unfilled Poly(Vinylidene Fluoride) PVDF |
| ASTM D 2241 : 2020 | Standard Specification for Poly(Vinyl Chloride) (PVC) Pressure-Rated Pipe (SDR Series) |
| ASTM F 810 : 2012 : R2018 | Standard Specification for Smoothwall Polyethylene (PE) Pipe for Use in Drainage and Waste Disposal Absorption Fields |
| ASTM D 638 : 2014 | Standard Test Method for Tensile Properties of Plastics |
| ASTM D 4634 : 2016 | Standard Classification System and Basis for Specification for Styrene-Maleic Anhydride Molding and Extrusion Materials (S/MA) |
| ASTM F 2561 : 2020 | Standard Practice for Rehabilitation of a Sewer Service Lateral and Its Connection to the Main Using a One Piece Main and Lateral Cured-in-Place Liner |
| ASTM F 2905/F2905M : 2021 | Standard Specification for Crosslinked Polyethylene (PEX) Line Pipe For Oil and Gas Producing Applications |
| ASTM F 794 : 2021 | Standard Specification for Poly(Vinyl Chloride) (PVC) Profile Gravity Sewer Pipe and Fittings Based on Controlled Inside Diameter |
| ASTM F 735 : 2017 | Standard Test Method for Abrasion Resistance of Transparent Plastics and Coatings Using the Oscillating Sand Method |
| ASTM D 817 : 2012 : R2019 | Standard Test Methods of Testing Cellulose Acetate Propionate and Cellulose Acetate Butyrate |
| ASTM D 2578 : 2017 | Standard Test Method for Wetting Tension of Polyethylene and Polypropylene Films |
| ASTM D 955 : 2021 | Standard Test Method of Measuring Shrinkage from Mold Dimensions of Thermoplastics |
| ASTM D 4470 : 2018 | Standard Test Method for Static Electrification |
| ASTM F 3123 : 2018 : REV A | Standard Specification for Metric Outside Diameter Polyethylene (PE) Plastic Pipe (DR-PN) |
| ASTM D 2673 : 2014 | Standard Specification for Oriented Polypropylene Film |
| ASTM F 793/F793M : 2020 | Standard Classification of Wall Coverings by Use Characteristics |
| ASTM E 2945 : 2014 : R2021 | Standard Test Method for Film Permeability Determination Using Static Permeability Cells |
| ASTM D 2466 : 2021 | Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Pipe Fittings, Schedule 40 |
| ASTM F 2818 : 2010 : R2019 | Standard Specification for Specification for Crosslinked Polyethylene (PEX) Material Gas Pressure Pipe and Tubing |
| ASTM D 116 : 1986 : R2020 | Standard Test Methods for Vitrified Ceramic Materials for Electrical Applications |
| ASTM D 3307 : 2016 | Standard Specification for Perfluoroalkoxy (PFA) Resin Molding and Extrusion Materials |
| ASTM F 877 : 2020 | Standard Specification for Crosslinked Polyethylene (PEX) Hot- and Cold-Water Distribution Systems |
| ASTM D 4495 : 2016 | Standard Test Method for Impact Resistance of Poly(Vinyl Chloride) (PVC) Rigid Profiles by Means of a Falling Weight |
| ASTM D 704 : 1999 : R2020 | Standard Specification for Melamine-Formaldehyde Molding Compounds |
| ASTM F 1505 : 2016 | Standard Specification for Insulated and Insulating Hand Tools |
| ASTM F 2648/F2648M : 2020 | Standard Specification for 2 to 60 inch [50 to 1500 mm] Annular Corrugated Profile Wall Polyethylene (PE) Pipe and Fittings for Land Drainage Applications |
| ASTM D 6261 : 2014 | Standard Specification for Extruded and Compression Molded Basic Shapes Made from Thermoplastic Polyester (TPES) |
| ASTM D 5926 : 2015 : R2020 | Standard Specification for Poly (Vinyl Chloride) (PVC) Gaskets for Drain, Waste, and Vent (DWV), Sewer, Sanitary, and Storm Plumbing Systems |
| ASTM D 3835 : 2016 | Standard Test Method for Determination of Properties of Polymeric Materials by Means of a Capillary Rheometer |
| ASTM D 5988 : 2018 | Standard Test Method for Determining Aerobic Biodegradation of Plastic Materials in Soil |
| ASTM D 7774 : 2017 | Standard Test Method for Flexural Fatigue Properties of Plastics |
| ASTM D 1621 : 2016 | Standard Test Method for Compressive Properties of Rigid Cellular Plastics |
| ASTM D 635 : 2018 | Standard Test Method for Rate of Burning and/or Extent and Time of Burning of Plastics in a Horizontal Position |
| ASTM F 667/F667M : 2016 : R2021 | Standard Specification for 3 through 24 in. Corrugated Polyethylene Pipe and Fittings |
| ASTM D 6262 : 2017 | Standard Specification for Extruded, Compression Molded, and Injection Molded Basic Shapes of Poly(aryl ether ketone) (PAEK) |
| ASTM F 409 : 2017 | Standard Specification for Thermoplastic Accessible and Replaceable Plastic Tube and Tubular Fittings |
| ASTM F 2562/F2562M : 2015 : R2019 | Specification for Steel Reinforced Thermoplastic Ribbed Pipe and Fittings for Non-Pressure Drainage and Sewerage |
| ASTM D 2517 : 2018 | Standard Specification for Reinforced Epoxy Resin Gas Pressure Pipe and Fittings |
| ASTM D 6324 : 2011 : R2017 | Standard Specification for Male Condoms Made from Polyurethane |
| ASTM D 5279 : 2013 | Standard Test Method for Plastics: Dynamic Mechanical Properties: In Torsion |
| ASTM D 494 : 2011(R2019) | Standard Test Method for Acetone Extraction of Phenolic Molded or Laminated Products |
| ASTM D 5205 : 2016 | Standard Classification System and Basis for Specification for Polyetherimide (PEI) Materials |
| ASTM D 7474 : 2017 | Standard Practice for Determining Residual Stresses in Extruded or Molded Sulfone Plastic (SP) Parts by Immersion in Various Chemical Reagents |
| ASTM F 2987 : 2012 : R2018 | Standard Specification for Corrugated Polyethylene Pipe and Fittings for Mine Heap Leach Aeration Applications (Withdrawn 2024) |
| ASTM D 1525 : 2017 : EDT 1 | Standard Test Method for Vicat Softening Temperature of Plastics |
| ASTM F 3371 : 2019 | Standard Specification for Polyolefin Pipe and Fittings for Drainage, Waste, and Vent Applications |
| ASTM D 2290 : 2019 : REV A | Standard Test Method for Apparent Hoop Tensile Strength of Plastic or Reinforced Plastic Pipe |
| ASTM D 2122 : 2016 | Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings |
| ASTM D 4024 : 2015 | Standard Specification for Machine Made “Fiberglass” (Glass-Fiber-Reinforced Thermosetting Resin) Flanges |
| ASTM D 5041 : 1998 : R2019 | Standard Test Method for Fracture Strength in Cleavage of Adhesives in Bonded Joints |
| ASTM D 790 : 2017 | Standard Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials |
| ASTM D 1337 : 2010 : R2021 | Standard Practice for Storage Life of Adhesives by Viscosity and Bond Strength |
| ASTM D 5338 : 2015 : R2021 | Standard Test Method for Determining Aerobic Biodegradation of Plastic Materials Under Controlled Composting Conditions, Incorporating Thermophilic Temperatures |
| ASTM D 2990 : 2017 | Standard Test Methods for Tensile, Compressive, and Flexural Creep and Creep-Rupture of Plastics |
| ASTM D 2442 : 1975 : R2020 | Standard Specification for Alumina Ceramics for Electrical and Electronic Applications |
| ASTM F 1281 : 2017 | Standard Specification for Crosslinked Polyethylene/Aluminum/Crosslinked Polyethylene (PEX-AL-PEX) Pressure Pipe |
| ASTM D 4020 : 2018 | Standard Specification for Ultra-High-Molecular-Weight Polyethylene Molding and Extrusion Materials |
| ASTM F 2947/F2947M : 2021 | Standard Specification for 150 to 1500 mm [6 to 60 in.] Annular Corrugated Profile-Wall Polyethylene (PE) Pipe and Fittings for Sanitary Sewer Applications |
| ASTM D 7292 : 2018 | Standard Specification for Extruded, Compression-Molded, and Injection-Molded Basic Shapes of Polyamide-Imide (PAI) |
| ASTM F 2159 : 2021 | Standard Specification for Plastic Insert Fittings Utilizing a Copper Crimp Ring, or Alternate Stainless Steel Clamps for SDR9 Crosslinked Polyethylene (PEX) Tubing and SDR9 Polyethylene of Raised Temperature (PE-RT) Tubing |
| ASTM D 2661 : 2014 : EDT 1 | Standard Specification for Acrylonitrile-Butadiene-Styrene (ABS) Schedule 40 Plastic Drain, Waste, and Vent Pipe and Fittings |
| ASTM D 3846 : 2008 : R2015 | Standard Test Method for In-Plane Shear Strength of Reinforced Plastics (Withdrawn 2024) |
| ASTM D 792 : 2020 | Standard Test Methods for Density and Specific Gravity (Relative Density) of Plastics by Displacement |
| ASTM D 3595 : 2014 : R2019 : EDT 1 | Standard Specification for Polychlorotrifluoroethylene (PCTFE) Extruded Plastic Sheet and Film |
| ASTM D 2996 : 2017 | Standard Specification for Filament-Wound “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe |
| ASTM D 3139 : 2019 | Standard Specification for Joints for Plastic Pressure Pipes Using Flexible Elastomeric Seals |
| ASTM D 256 : 2010 : R2018 | Standard Test Methods for Determining the Izod Pendulum Impact Resistance of Plastics |
| ASTM D 2561 : 2017 | Standard Test Method for Environmental Stress-Crack Resistance of Blow-Molded Polyethylene Containers |
| ASTM D 3679 : 2017 | Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Siding |
| ASTM D 2239 : 2012 : REV A : R2020 | Standard Specification for Polyethylene (PE) Plastic Pipe (SIDR-PR) Based on Controlled Inside Diameter |
| ASTM D 1708 : 2018 | Standard Test Method for Tensile Properties of Plastics by Use of Microtensile Specimens |
| ASTM D 5990 : 2020 : REV A | Standard Classification System and Basis for Polyketone Injection Molding and Extrusion Materials (PK) |
| ASTM F 3036 : 2013 | Standard Guide for Testing Absorbable Stents |
| ASTM D 1434 : 1982 : R2015 : EDT 1 | Standard Test Method for Determining Gas Permeability Characteristics of Plastic Film and Sheeting |
| ASTM D 5204 : 2019 | Standard Classification System and Basis for Specification for Polyamide-Imide (PAI) Molding and Extrusion Materials |
| ASTM D 2732 : 2014 : R2020 | Standard Test Method for Unrestrained Linear Thermal Shrinkage of Plastic Film<brk/> and Sheeting |
| ASTM D 4203 : 2017 | Standard Specification for and Basis for Specifications for Styrene-Acrylonitrile (SAN) Injection and Extrusion Materials |
| ASTM D 7293 : 2019 | Standard Specification for Extruded and Compression-Molded Shapes Made from Polyetherimide (PEI) |
| ASTM D 4067 : 2016 | Standard Classification System and Basis for Specification for Reinforced and Filled Poly(Phenylene Sulfide) (PPS) Injection Molding and Extrusion Materials Using ASTM Methods |
| ASTM D 1784 : 2020 | Standard Classification System and Basis for Specification for Rigid Poly(Vinyl Chloride) (PVC) Compounds and Chlorinated Poly(Vinyl Chloride) (CPVC) Compounds |
| ASTM D 6988 : 2013 | Standard Guide for Determination of Thickness of Plastic Film Test Specimens |
| ASTM D 3354 : 2015 | Standard Test Method for Blocking Load of Plastic Film by the Parallel Plate Method |
| ASTM F 791 : 2018 | Standard Test Method for Stress Crazing of Transparent Plastics |
| ASTM D 4065 : 2020 | Standard Practice for Plastics: Dynamic Mechanical Properties: Determination and Report of Procedures |
| ASTM D 5336 : 2015 : REV A | Standard Classification System and Basis for Specification for Polyphthalamide (PPA) Injection Molding Material |
| ASTM D 3299 : 2018 | Standard Specification for Filament-Wound Glass-Fiber-Reinforced Thermoset Resin Corrosion-Resistant Tanks |
| ASTM F 2468 : 2005 : R2019 | Standard Classification for Specifying Silicone Adhesives and Sealants for Transportation Applications |
| ASTM D 3368 : 2017 | Standard Specification for FEP Sheet and Film |
| ASTM D 2739 : 1997 : R2017 | Standard Test Method for Volume Resistivity of Conductive Adhesives |
| ASTM D 2765 : 2016 | Standard Test Methods for Determination of Gel Content and Swell Ratio of Crosslinked Ethylene Plastics |
| ASTM F 1732 : 2012 : R2018 | Standard Specification for Poly(Vinyl Chloride) (PVC) Sewer and Drain Pipe Containing Recycled PVC Material |
| ASTM D 542 : 2014 | Standard Test Method for Index of Refraction of Transparent Organic Plastics |
| ASTM D 6339 : 2011 : R2019 | Standard Classification System for and Basis for Specifications for Syndiotactic Polystyrene Molding and Extrusion (SPS) |
| ASTM F 1697 : 2018 | Standard Specification for Poly(Vinyl Chloride) (PVC) Profile Strip for Machine Spiral-Wound Liner Pipe Rehabilitation of Existing Sewers and Conduit |
| ASTM D 4726 : 2018 | Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Exterior-Profile Extrusions Used for Assembled Windows and Doors |
| ASTM D 7793 : 2020 | Standard Specification for Insulated Vinyl Siding |
| ASTM D 1710 : 2015 | Standard Specification for Extruded Polytetrafluoroethylene (PTFE) Rod, Heavy Walled Tubing and Basic Shapes |
| ASTM G 175 : 2013 | Standard Test Method for Evaluating the Ignition Sensitivity and Fault Tolerance of Oxygen Pressure Regulators Used for Medical and Emergency Applications |
| ASTM F 2785 : 2020 : EDT 1 | Standard Specification for Polyamide 12 Gas Pressure Pipe, Tubing, and Fittings |
| ASTM F 1499 : 2017 | Standard Specification for Coextruded Composite Drain, Waste, and Vent Pipe (DWV) |
| ASTM D 2584 : 2018 | Standard Test Method for Ignition Loss of Cured Reinforced Resins |
| ASTM D7444 : 2018 : REV A | Standard Practice for Heat and Humidity Aging of Oxidatively Degradable Plastics<br> |
| ASTM D 5420 : 2021 | Standard Test Method for Impact Resistance of Flat, Rigid Plastic Specimen by Means of a Striker Impacted by a Falling Weight (Gardner Impact) |
| ASTM D 5870 : 2016 | Standard Practice for Calculating Property Retention Index of Plastics |
| ASTM D 4066 : 2013 : R2019 | Standard Classification System for Nylon Injection and Extrusion Materials (PA) |
| ASTM D 7853 : 2013 : R2020 | Standard Test Method for Hydraulic Pullout Resistance of a Geomembrane with Locking Extensions Embedded in Concrete |
| ASTM D 5511 : 2018 | Standard Test Method for Determining Anaerobic Biodegradation of Plastic Materials Under High-Solids Anaerobic-Digestion Conditions |
| ASTM D 5857 : 2017 | Standard Specification for Polypropylene Injection and Extrusion Materials Using ISO Protocol and Methodology |
| ASTM D 2684/D2684M : 2015 | Standard Test Method for Permeability of Thermoplastic Containers to Packaged Reagents or Proprietary Products (Withdrawn 2024) |
| ASTM D 5083 : 2017 | Standard Test Method for Tensile Properties of Reinforced Thermosetting Plastics Using Straight-Sided Specimens |
| ASTM D 2464 : 2015 | Standard Specification for Threaded Poly(Vinyl Chloride) (PVC) Plastic Pipe Fittings, Schedule 80 |
| ASTM D 3035 : 2015 | Standard Specification for Polyethylene (PE) Plastic Pipe (DR-PR) Based on Controlled Outside Diameter |
| ASTM D 4350 : 2016 | Standard Test Method for Corrosivity Index of Plastics and Fillers |
| ASTM D 1746 : 2015 | Standard Test Method for Transparency of Plastic Sheeting |
| ASTM D 5893/D5893M : 2016 : R2021 | Standard Specification for Cold-Applied, Single-Component, Chemically Curing Silicone Joint Sealant for Portland Cement Concrete Pavements |
| ASTM F 876 : 2020 : REV B | Standard Specification for Crosslinked Polyethylene (PEX) Tubing |
| ASTM F 2953 : 2012 : R2021 | Standard Specification for Phenolic Raw Materials for the Use in Bearing Cages |
| ASTM D 6263 : 2015 | Standard Specification for Extruded Rods and Bars Made From Rigid Poly(Vinyl Chloride) (PVC) and Chlorinated Poly(Vinyl Chloride) (CPVC) |
| ASTM D 3528 : 1996 : R2016 | Standard Test Method for Strength Properties of Double Lap Shear Adhesive Joints by Tension Loading |
| ASTM D 2924 : 2012 : R2017 | Standard Test Method for External Pressure Resistance of “Fiberglass”<brk /> (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe |
| ASTM D 6041 : 2018 | Standard Specification for Contact-Molded “Fiberglass” (Glass-Fiber-Reinforced Thermosetting Resin) Corrosion Resistant Pipe and Fittings |
| ASTM D 2997 : 2021 | Standard Specification for Centrifugally Cast “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe |
| ASTM G 147 : 2017 | Standard Practice for Conditioning and Handling of Nonmetallic Materials for Natural and Artificial Weathering Tests |
| ASTM D 5171 : 2015 : R2020 | Standard Test Method for Impact Resistance of Plastic Sew-Through Buttons |
| ASTM D 1929 : 2020 | Standard Test Method for Determining Ignition Temperature of Plastics |
| ASTM D 5170 : 1998 : R2021 | Standard Test Method for Peel Strength (“T” Method) of Hook and Loop Touch Fasteners |
| ASTM D 2240 : 2015 : R2021 | Standard Test Method for Rubber Property—Durometer Hardness |
| ASTM D 3013 : 2013 : R2021 | Standard Specification for Epoxy Molding Compounds |
| ASTM D 3350 : 2021 | Standard Specification for Polyethylene Plastics Pipe and Fittings Materials |
| ASTM D 4475 : 2021 | Standard Test Method for Apparent Horizontal Shear Strength of Pultruded Reinforced Plastic Rods By the Short-Beam Method |
| ASTM F 2929 : 2017 : R2021 | Standard Specification for Crosslinked Polyethylene (PEX) Tubing of 0.070 in. Wall and Fittings for Radiant Heating Systems up to 75 psig |
| ASTM D 2116 : 2016 : R2021 | Standard Specification for FEP Resin Molding and Extrusion Materials |
| ASTM D 5279 : 2021 | Standard Test Method for Plastics: Dynamic Mechanical Properties: In Torsion |
| ASTM D 5169 : 1998 : R2021 | Standard Test Method for Shear Strength (Dynamic Method) of Hook and Loop Touch Fasteners |
| ASTM F 2785 : 2021 | Standard Specification for Polyamide 12 Gas Pressure Pipe, Tubing, and Fittings |
| ASTM F 2905/F2905M : 2021 : REV A | Standard Specification for Crosslinked Polyethylene (PEX) Line Pipe For Oil and Gas Producing Applications |
| ASTM D 4000 : 2013 | Standard Classification System for Specifying Plastic Materials |
| ASTM D 4000 : 2003 : REV A | Standard Classification System for Specifying Plastic Materials |
| ASTM D 4000 : 2000 : REV A | Standard Classification System for Specifying Plastic Materials |
| ASTM D 4000 : 2012 | Standard Classification System for Specifying Plastic Materials |
| ASTM D 4000 : 2009 | Standard Classification System for Specifying Plastic Materials |
| ASTM D 4000 : 2011 | Standard Classification System for Specifying Plastic Materials |
| ASTM D 4000 : 2004 : EDT 1 | Standard Classification System for Specifying Plastic Materials |
| ASTM D 4000 : 2009 : REV B | Standard Classification System for Specifying Plastic Materials |
| ASTM D 4000 : 2000 | Standard Classification System for Specifying Plastic Materials |
| ASTM D 4000 : 2010 : REV A | Standard Classification System for Specifying Plastic Materials |
| ASTM D 4000 : 2007 | Standard Classification System for Specifying Plastic Materials |
| ASTM D 4000 : 2009 : REV A | Standard Classification System for Specifying Plastic Materials |
| ASTM D 4000 : 2001 | Standard Classification System for Specifying Plastic Materials |
| ASTM D 5032 : 2011 | Standard Practice for Maintaining Constant Relative Humidity by Means of Aqueous Glycerin Solutions |
| ASTM D 4000 : 2008 | Standard Classification System for Specifying Plastic Materials |
| ASTM D 4000 : 2001 : REV A : EDT 1 | Standard Classification System for Specifying Plastic Materials |
| ASTM D 4000 : 2004 | Standard Classification System for Specifying Plastic Materials |
| ASTM D 5032 : 2019 | Standard Practice for Maintaining Constant Relative Humidity by Means of Aqueous Glycerin Solutions |
| ASTM D 4000 : 2010 | Standard Classification System for Specifying Plastic Materials |
| ASTM D 5032 : 1997 | Standard Practice for Maintaining Constant Relative Humidity by Means of Aqueous Glycerin Solutions |
| ASTM D 4000 : 2003 | Standard Classification System for Specifying Plastic Materials |
£55.10
Excluding VAT
GBP
CAD
CHF
CNY
DKK
EUR
GBP
HKD
IDR
INR
JPY
KRW
MXN
NOK
NZD
SEK
SGD
USD
ZAR
Hardcopy - English
PDF - English
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.