• There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

ASTM D 619 : 2021

Current
Current

The latest, up-to-date edition.

Standard Test Methods for Vulcanized Fibre Used for Electrical Insulation
Available format(s)

Hardcopy , PDF

Language(s)

English

Published date

15-02-2021

1.1These test methods cover the procedures for testing vulcanized fibre sheets, rolls, tubes, and rods of such grades as can be used for electrical insulation.

1.2The procedures appear in the following sections:

Procedure

Section

Arc Resistance

23

Ash

6

Bond Strength (Ply Adhesion)

16

Bursting Strength

14

Compressive Strength

12, 25, 30

Conditioning

4

Density

17, 26, 32

Dielectric Strength

18, 27

Dimensional Measurements

28, 33

Flammability

22

Flexural Strength

13, 31

Silica

7

Tearing Strength

11

Tensile Strength

10, 24, 29

Thickness (Sheets)

20

Resistance to Impact

15

Rockwell Hardness

19

Volatile Matter

8

Water Absorption

5

Zinc Chloride

9

1.3The values stated in inch-pound units are to be regarded as the standard. The SI values given in parentheses are for information only.

1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific hazard statements are given in 7.3, 22.1, and 22.2.

Note 1:The test methods described herein are similar technically to those described in IEC Publication 60667-2. Not all of the tests in this document are included in IEC 60667-2, and the procedures in the two publications are not completely identical; but it is expected that comparable results will be obtained from most of the procedures. Conduct comparative tests if necessary before directly comparing results of tests using the different procedures.

1.5This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Committee
D 09
DocumentType
Test Method
Pages
8
PublisherName
American Society for Testing and Materials
Status
Current
Supersedes

ASTM D 710 : 2019 Standard Specification for Vulcanized Fibre Sheets, Rolls, Rods, and Tubes Used for Electrical Insulation
ASTM D 229 : 2019 : EDT 1 Standard Test Methods for Rigid Sheet and Plate Materials Used for Electrical Insulation

ASTM D 202 : 2017 Standard Test Methods for Sampling and Testing Untreated Paper Used for Electrical Insulation
ASTM D 256 : 2010 : R2018 Standard Test Methods for Determining the Izod Pendulum Impact Resistance of Plastics
ASTM D 495 : 2014 Standard Test Method for High-Voltage, Low-Current, Dry Arc Resistance of Solid Electrical Insulation
ASTM D 689 : 2017 Standard Test Method for Internal Tearing Resistance of Paper
ASTM D 256 : 2023 : EDT 1 Standard Test Methods for Determining the Izod Pendulum Impact Resistance of Plastics
ASTM D 256 : 2023 Standard Test Methods for Determining the Izod Pendulum Impact Resistance of Plastics
ASTM D 202 : 2023 Standard Test Methods for Sampling and Testing Untreated Paper Used for Electrical Insulation
ASTM D 1711 : 2024 Standard Terminology Relating to Electrical Insulation
ASTM D 785 : 2008 : R2015 Standard Test Method for Rockwell Hardness of Plastics and Electrical Insulating Materials
ASTM D 695 : 2015 Standard Test Method for Compressive Properties of Rigid Plastics
ASTM D 1711 : 2022 Standard Terminology Relating to Electrical Insulation
ASTM D 952 : 2015 : R2021 Standard Test Method for Bond or Cohesive Strength of Sheet Plastics and Electrical Insulating Materials
ASTM D 570 : 2022 Standard Test Method for Water Absorption of Plastics
ASTM D 1711 : 2020 Standard Terminology Relating to Electrical Insulation
ASTM D 785 : 2023 Standard Test Method for Rockwell Hardness of Plastics and Electrical Insulating Materials
ASTM D 828 : 2016 : EDT 1 Standard Test Method for Tensile Properties of Paper and Paperboard Using Constant-Rate-of-Elongation Apparatus
ASTM D 695 : 2023 Standard Test Method for Compressive Properties of Rigid Plastics
ASTM D 570 : 1998 : R2018 Standard Test Method for Water Absorption of Plastics
ASTM D 689 : 2017 : R2024 Standard Test Method for Internal Tearing Resistance of Paper
ASTM D 6054 : 1997 : R2004 Standard Practice for Conditioning Electrical Insulating Materials for Testing (Withdrawn 2012)
ASTM D 495 : 2022 Standard Test Method for High-Voltage, Low-Current, Dry Arc Resistance of Solid Electrical Insulation
ASTM D 828 : 2022 Standard Test Method for Tensile Properties of Paper and Paperboard Using Constant-Rate-of-Elongation Apparatus
ASTM D 952 : 2015 Standard Test Method for Bond or Cohesive Strength of Sheet Plastics and Electrical Insulating Materials

View more information
£52.59
Excluding VAT

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.