• There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

ASTM D 6416/D6416M : 2016

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Standard Test Method for Two-Dimensional Flexural Properties of Simply Supported Sandwich Composite Plates Subjected to a Distributed Load
Available format(s)

Hardcopy , PDF

Superseded date

08-04-2021

Language(s)

English

Published date

13-04-2016

1.1This test method determines the two-dimensional flexural properties of sandwich composite plates subjected to a distributed load. The test fixture uses a relatively large square panel sample which is simply supported all around and has the distributed load provided by a water-filled bladder. This type of loading differs from the procedure of Test Method C393, where concentrated loads induce one-dimensional, simple bending in beam specimens.

1.2This test method is applicable to composite structures of the sandwich type which involve a relatively thick layer of core material bonded on both faces with an adhesive to thin-face sheets composed of a denser, higher-modulus material, typically, a polymer matrix reinforced with high-modulus fibers.

1.3The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text the inch-pound units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.

1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Committee
D 30
DocumentType
Test Method
Pages
12
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy
Supersedes

ASTM D 4762 : 2018 Standard Guide for Testing Polymer Matrix Composite Materials

ASTM D 3171 : 1999 Standard Test Methods for Constituent Content of Composite Materials
ASTM D 2584 : 2002 Standard Test Method for Ignition Loss of Cured Reinforced Resins
ASTM D 3878 : 2002 : REV A Standard Terminology for Composite Materials
ASTM E 1237 : 1993 : R1998 Standard Guide for Installing Bonded Resistance Strain Gages
ASTM D 3878 : 2015 Standard Terminology for Composite Materials
ASTM D 2584 : 2008 Standard Test Method for Ignition Loss of Cured Reinforced Resins
ASTM D 3878 : 2019 Standard Terminology for Composite Materials
ASTM D 3878 : 2000 Standard Terminology Composite Materials
ASTM D 2584 : 1994 Standard Test Method for Ignition Loss of Cured Reinforced Resins
ASTM D 3171 : 2011 Standard Test Methods for Constituent Content of Composite Materials
ASTM E 6 : 2002 Standard Terminology Relating to Methods of Mechanical Testing
ASTM D 2734 : 2016 Standard Test Methods for Void Content of Reinforced Plastics
ASTM D 3878 : 2003 : REV A Standard Terminology for Composite Materials
ASTM D 2584 : 2011 Standard Test Method for Ignition Loss of Cured Reinforced Resins
ASTM E 1237 : 1993 : R2009 Standard Guide for Installing Bonded Resistance Strain Gages
ASTM D 3878 : 2016 Standard Terminology for Composite Materials
ASTM D 3878 : 2019 : REV A Standard Terminology for Composite Materials
ASTM D 3878 : 2020 : REV A Standard Terminology for Composite Materials
ASTM D 3878 : 1998 Standard Terminology Composite Materials
ASTM D 3878 : 2018 Standard Terminology for Composite Materials
ASTM D 3171 : 2009 Standard Test Methods for Constituent Content of Composite Materials
ASTM D 3878 : 2002 Standard Terminology for Composite Materials
ASTM E 1237 : 1993 : R2003 Standard Guide for Installing Bonded Resistance Strain Gages
ASTM D 2584 : 1968 Standard Method Of Test For Ignition Loss Of Cured Reinforced Resins
ASTM D 3878 : 2004 Standard Terminology for Composite Materials
ASTM E 1237 : 1993 : R2014 Standard Guide for Installing Bonded Resistance Strain Gages
ASTM D 2734 : 1994 Standard Test Methods for Void Content of Reinforced Plastics
ASTM D 3878 : 2007 : R2013 Standard Terminology for Composite Materials
ASTM D 3878 : 2020 : REDLINE Standard Terminology for Composite Materials
ASTM D 3878 : 2020 Standard Terminology for Composite Materials
ASTM D 2584 : 2018 Standard Test Method for Ignition Loss of Cured Reinforced Resins
ASTM D 3878 : 2003 Standard Terminology for Composite Materials
ASTM D 3878 : 2007 Standard Terminology for Composite Materials
ASTM D 2734 : 2009 Standard Test Methods for Void Content of Reinforced Plastics
ASTM D 3171 : 1999 : R2004 Standard Test Methods for Constituent Content of Composite Materials
ASTM D 3171 : 2015 Standard Test Methods for Constituent Content of Composite Materials
ASTM D 3878 : 2004 : REV A Standard Terminology for Composite Materials
ASTM D 3171 : 2006 Standard Test Methods for Constituent Content of Composite Materials
ASTM D 3878 : 2001 Standard Terminology Composite Materials

View more information
£69.29
Excluding VAT

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.