• There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

ASTM D 6750 : 2017

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Standard Test Methods for Evaluation of Engine Oils in a High-Speed, Single-Cylinder Diesel Engine—1K Procedure (0.4 % Fuel Sulfur) and 1N Procedure (0.04 % Fuel Sulfur)
Available format(s)

Hardcopy , PDF

Superseded date

17-05-2017

Language(s)

English

Published date

01-05-2017

1.1These test methods cover the performance of engine oils intended for use in certain diesel engines. They are performed in a standardized high-speed, single-cylinder diesel engine by either the 1K (0.4 % mass fuel sulfur) or 1N (0.04 % mass fuel sulfur) procedure.3 The only difference in the two test methods is the fuel used. Piston and ring groove deposit-forming tendency and oil consumption are measured. Also, the piston, the rings, and the liner are examined for distress and the rings for mobility. These test methods are required to evaluate oils intended to satisfy API service categories CF-4 and CH-4 for 1K, and CG-4 for 1N of Specification D4485.

1.2These test methods, although based on the original Caterpillar 1K/1N procedures,3 also embody TMC information letters issued before these test methods were first published. These test methods are subject to frequent change. Until the next revision of these test methods, TMC will update changes in these test methods by the issuance of information letters which shall be obtained from TMC (see Annex A1 – Annex A4).

1.3The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.

1.3.1Exception—Where there is no direct SI equivalent such as screw threads, national pipe threads/diameters, tubing size, or single source equipment specified. Also Brake Specific Fuel Consumption is measured in kilograms per kilowatthour.

1.4The following is the Table of Contents:

Section

Introduction

Scope

1

Referenced documents

2

Terminology

3

Summary of Test Methods

4

Significance and Use

5

Apparatus

6

General Laboratory Requirements

6.1

Test Engine

6.2

Test Engine Accessories and Parts

6.3

Reagents and Materials

7

Test Oil Sample Requirements

8

Preparation of Apparatus

9

Engine Inspection

9.1

Engine Pre-Test Lubrication System Flush

9.2

Engine Pre-Test Measurements and Inspections

9.3

Engine Assembly

9.4

Pressure Testing of Fuel System Assembly

9.5

Calibration of Engine Test Stand

10

General Requirements and Frequency of Calibration

10.1

Runs

10.2

Specified Test Parameters

10.3

Calibration Test Acceptance Criteria

10.4

Action on Rejection of Calibration Test

10.5

Test Numbering

10.6

Reference Oils

10.7

Severity Adjustments

10.8

Engine Operating Procedure

11

Engine Run-In

11.1

Cool-Down Procedure

11.2

Warm-Up Procedure

11.3

Operating Conditions and Oil Additions

11.4

Measurement of Oil Consumption

11.5

Sampling Used Oil

11.6

Shutdowns, Lost Time and Off Tolerance Conditions

11.7

Recording of Exhaust Temperature

11.8

Air-Fuel Ratio Measurement

11.9

Recording of Engine Conditions

11.10

Humidity Requirements/Calibration/Measurement

11.11

Inspections, Photographs and Measurements

12

Reference to Reporting Form

12.1

Pre-Test Measurements of Engine Parts

12.2

Post-Test Information

12.3

Oil Inspections

12.4

Report

13

General Directions

13.1

Electronic Transmission of Test Results (Optional)

13.12

Reporting Calibration Test Results

13.13

Precision and Bias

14

Keywords

15

ANNEXES

ASTM Test Monitoring Center Organization

Annex A1

ASTM Test Monitoring Center: Calibration Procedures

Annex A2

ASTM Test Monitoring Center: Maintenance Activities

Annex A3

ASTM Test Monitoring Center: Related Information

Annex A4

Specifications for Test Engine and Engine Build

Annex A5

Intake Air System Details

Annex A6

Exhaust System Details

Annex A7

Cooling System Details

Annex A8

Oil System Modifications and Instrument Locations

Annex A9

Other Pressure and Temperature Measurement Locations

Annex A10

Oil Consumption Linear Regression Method

Annex A11

Test Fuel Specifications

Annex A12

Lubrication System, Flush Apparatus and Procedure

Annex A13

Engine Operating Conditions

Annex A14

Procedure for Rating Piston and Liner

Annex A15

Calculation of Percent Offset and Percent Deviation

Annex A16

1K/1N Test Reporting

Annex A17

Parts List by Part Number (P/N) and Warranty

Annex A18

Safety Precautions

Annex A19

APPENDIXES

Humidity Data

Appendix X1

Statistical Equations for Mean and Standard Deviation

Appendix X2

Examples of Forms for Reporting

Appendix X3

Optional Recording of Oil Pass Limits

Appendix X4

1.5This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Specific precautionary statements appear throughout the text. Being engine tests, these test methods do have definite hazards that shall be met by safe practices (see Annex A19 on Safety Precautions).

1.6This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Committee
D 02
DocumentType
Test Method
Pages
71
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy
Supersedes

ASTM D 7320 : 2018 Standard Test Method for Evaluation of Automotive Engine Oils in the Sequence IIIG, Spark-Ignition Engine
ASTM D 4485 : 2018 : REV A Standard Specification for Performance of Active API Service Category Engine Oils
ASTM D 6984 : 2018 Standard Test Method for Evaluation of Automotive Engine Oils in the Sequence IIIF, Spark-Ignition Engine
ASTM D 6837 : 2013 Standard Test Method for Measurement of Effects of Automotive Engine Oils on Fuel Economy of Passenger Cars and Light-Duty Trucks in Sequence VIB Spark Ignition Engine<rangeref></rangeref > (Withdrawn 2022)
ASTM D 7589 : 2016 Standard Test Method for Measurement of Effects of Automotive Engine Oils on Fuel Economy of Passenger Cars and Light-Duty Trucks in Sequence VID Spark Ignition Engine<rangeref></rangeref >

View more information
£104.35
Excluding VAT

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.