ASTM D 6823 : 2008 : R2013
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
Standard Specification for Commercial Boiler Fuels With Used Lubricating Oils
Available format(s)
Hardcopy , PDF
Superseded date
05-01-2022
Language(s)
English
Published date
09-08-2013
CONTAINED IN VOL. 05.04, 2015 Defines four grades of fuel oil made of at least 25% used lubricating oils.
1.1This specification covers four grades of fuel oil made of at least 25 % used lubricating oils. The four grades of fuel are intended for use in various types of fuel-oil-burning industrial equipment and commercial boilers under various climatic and operating conditions. These fuels are not intended for use in residential heaters.
1.1.1Grades RFC4, RFC5L, RFC5H and RFC6 are used lubricating oil blends of increasing viscosity, with or without middle distillate or residual fuel oil, or both, that are intended for use in industrial burners and commercial boilers equipped to handle these types of fuels. This specification is for applications where Specification D6448 would not meet the performance or other requirements of the burner or boiler in question.
Note 1—For information on the significance of the terminology and test methods used in this specification, see Appendix X1.
1.2This specification is for use in contracts for the purchase of fuel oils derived from used lubricating oil and for the guidance of consumers of such fuels. This specification does not address the frequency with which any particular test must be run.
1.3Nothing in this specification shall preclude observance of national or local regulations which can be more restrictive. In some jurisdictions, used oil is considered a hazardous waste and fuels derived from used oil are required to meet certain criteria before use as a fuel.
Note 2—For United States federal requirements imposed on used oil generators, transporters and transfer facilities, reprocessors, marketers, and burners, see 40 CFR Part 279.
Note 3—The generation and dissipation of static electricity can create problems in the handling of distillate burner fuel oils. For more information on the subject, see Guide D4865.
1.4The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.4.1Exception—Table 1 and Table X1.1 include inch-pound values in parentheses for information only.
| Committee |
D 02
|
| DocumentType |
Standard
|
| Pages |
7
|
| ProductNote |
Reconfirmed 2013
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| ASTM D 7666 : 2012 : R2019 | Standard Specification for Triglyceride Burner Fuel |
| ASTM D 7666 : 2012 | Standard Specification for Triglyceride Burner Fuel |
| ASTM D 4175 : 2020 | Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants |
| ASTM D 4175 : 2014 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
| ASTM D 4057 : 2019 | Standard Practice for Manual Sampling of Petroleum and Petroleum Products |
| ASTM D 2622 : 1992 : EDT 1 | Standard Test Method for Sulfur in Petroleum Products by X-Ray Spectrometry |
| ASTM D 4175 : 2009 : REV A : EDT 1 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
| ASTM D 4865 : 2019 | Standard Guide for Generation and Dissipation of Static Electricity in Petroleum Fuel Systems |
| ASTM D 4175 : 2008 : REV B : EDT 1 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
| ASTM D 1552 : 2003 | Standard Test Method for Sulfur in Petroleum Products (High-Temperature Method) |
| ASTM D 974 : 2014 : EDT 2 | Standard Test Method for Acid and Base Number by Color-Indicator Titration |
| ASTM D 4057 : 1995 | Standard Practice for Manual Sampling of Petroleum and Petroleum Products |
| ASTM D 2983 : 2019 | Standard Test Method for Low-Temperature Viscosity of Automatic Transmission Fluids, Hydraulic Fluids, and Lubricants using a Rotational Viscometer |
| ASTM D 974 : 2001 | Standard Test Method for Acid and Base Number by Color-Indicator Titration |
| ASTM D 2983 : 2002 | Standard Test Method for Low-Temperature Viscosity of Lubricants Measured by Brookfield Viscometer |
| ASTM D 473 : 1981 : R1995 : EDT 2 | Standard Test Method for Sediment in Crude Oils and Fuel Oils by the Extraction Method |
| ASTM D 6450 : 2012 | Standard Test Method for Flash Point by Continuously Closed Cup (CCCFP) Tester |
| ASTM D 6450 : 2016 : REV A | Standard Test Method for Flash Point by Continuously Closed Cup (CCCFP) Tester |
| ASTM D 2622 : 1987 : EDT 1 | Standard Test Method for Sulfur in Petroleum Products by X-Ray Spectrometry |
| ASTM D 3245 : 2003 | Standard Test Method for Pumpability of Industrial Fuel Oils (Withdrawn 2010) |
| ASTM D 4865 : 2009 : R2014 | Standard Guide for Generation and Dissipation of Static Electricity in Petroleum Fuel Systems |
| ASTM D 4175 : 2005 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
| ASTM D 5291 : 2010 : R2015 | Standard Test Methods for Instrumental Determination of Carbon, Hydrogen, and Nitrogen in Petroleum Products and Lubricants |
| ASTM D 3828 : 2002 | Standard Test Methods for Flash Point by Small Scale Closed Cup Tester |
| ASTM D 2983 : 2017 | Standard Test Method for Low-Temperature Viscosity of Automatic Transmission Fluids, Hydraulic Fluids, and Lubricants using a Rotational Viscometer |
| ASTM D 4175 : 2005 : EDT 2 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
| ASTM D 1298 : 2012 : REV A | Standard Test Method for Density, Relative Density (Specific Gravity), or API Gravity of Crude Petroleum and Liquid Petroleum Products by Hydrometer Method |
| ASTM D 1796 : 2011 | Standard Test Method for Water and Sediment in Fuel Oils by the Centrifuge Method (Laboratory Procedure) |
| ASTM D 4177 : 2016 : EDT 1 | Standard Practice for Automatic Sampling of Petroleum and Petroleum Products |
| ASTM D 6160 : 1998 | Standard Test Method for Determination of Polychlorinated Biphenyls (PCBs) in Waste Materials by Gas Chromatography |
| ASTM D 3228 : 2008 : R2019 | Standard Test Method for Total Nitrogen in Lubricating Oils and Fuel Oils by Modified Kjeldahl Method |
| ASTM D 7042 : 2019 : EDT 1 | Standard Test Method for Dynamic Viscosity and Density of Liquids by Stabinger Viscometer (and the Calculation of Kinematic Viscosity) |
| ASTM D 3228 : 2019 | Standard Test Method for Total Nitrogen in Lubricating Oils and Fuel Oils by Modified Kjeldahl Method |
| ASTM D 5185 : 1997 | Standard Test Method for Determination of Additive Elements, Wear Metals, and Contaminants in Used Lubricating Oils and Determination of Selected Elements in Base Oils by Inductively Coupled Plasma Atomic Emission Spectrometry (ICP-AES) |
| ASTM D 4175 : 2015 : REV C | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
| ASTM D 1266 : 1998 | Standard Test Method for Sulfur in Petroleum Products (Lamp Method) |
| ASTM D 4629 : 2002 : R2007 | Standard Test Method for Trace Nitrogen in Liquid Petroleum Hydrocarbons by Syringe/Inlet Oxidative Combustion and Chemiluminescence Detection |
| ASTM D 4175 : 2020 : REV B | Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants |
| ASTM D 4175 : 2017 : REV A : EDT 1 | Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants |
| ASTM D 6448 : 2016 | Standard Specification for Industrial Burner Fuels from Used Lubricating Oils |
| ASTM D 396 : 2020 | Standard Specification for Fuel Oils |
| ASTM D 4052 : 1996 : R2002 : EDT 1 | Standard Test Method for Density and Relative Density of Liquids by Digital Density Meter |
| ASTM D 5291 : 1992 | Standard Test Methods for Instrumental Determination of Carbon, Hydrogen, and Nitrogen in Petroleum Products and Lubricants |
| ASTM D 3828 : 2012 : REV A | Standard Test Methods for Flash Point by Small Scale Closed Cup Tester |
| ASTM D 7042 : 2012 | Standard Test Method for Dynamic Viscosity and Density of Liquids by Stabinger Viscometer (and the Calculation of Kinematic Viscosity) |
| ASTM D 3828 : 1998 | Standard Test Methods for Flash Point by Small Scale Closed Tester |
| ASTM D 1552 : 2008 : R2014 | Standard Test Method for Sulfur in Petroleum Products (High-Temperature Method) |
| ASTM D 1298 : 2012 : REV B | Standard Test Method for Density, Relative Density, or API Gravity of Crude Petroleum and Liquid Petroleum Products by Hydrometer Method |
| ASTM D 4865 : 2009 | Standard Guide for Generation and Dissipation of Static Electricity in Petroleum Fuel Systems |
| ASTM D 2983 : 2002 : REV A | Standard Test Method for Low-Temperature Viscosity of Lubricants Measured by Brookfield Viscometer |
| ASTM D 4177 : 1995 | Standard Practice for Automatic Sampling of Petroleum and Petroleum Products |
| ASTM D 2983 : 2002 : REV B | Standard Test Method for Low-Temperature Viscosity of Lubricants Measured by Brookfield Viscometer |
| ASTM D 4175 : 2008 : REV A | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
| ASTM D 4175 : 2020 : REV A | Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants |
| ASTM D 4057 : 2012 : R2018 | Standard Practice for Manual Sampling of Petroleum and Petroleum Products |
| ASTM D 4294 : 2010 | Standard Test Method for Sulfur in Petroleum and Petroleum Products by Energy Dispersive X-ray Fluorescence Spectrometry |
| ASTM D 4052 : 2018 : REV A | Standard Test Method for Density, Relative Density, and API Gravity of Liquids by Digital Density Meter |
| ASTM D 3828 : 2007 | Standard Test Methods for Flash Point by Small Scale Closed Cup Tester |
| ASTM D 396 : 1998 | Standard Specification for Fuel Oils |
| ASTM D 4175 : 2017 : REV B | Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants |
| ASTM D 4175 : 2009 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
| ASTM D 1552 : 1990 : EDT 1 | Standard Test Method for Sulfur in Petroleum Products (High-Temperature Method) |
| ASTM D 5291 : 2010 | Standard Test Methods for Instrumental Determination of Carbon, Hydrogen, and Nitrogen in Petroleum Products and Lubricants |
| ASTM D 1266 : 2013 | Standard Test Method for Sulfur in Petroleum Products (Lamp Method) |
| ASTM D 3828 : 2016 : REV A : R2021 | Standard Test Methods for Flash Point by Small Scale Closed Cup Tester |
| ASTM D 6450 : 2012 : EDT 1 | Standard Test Method for Flash Point by Continuously Closed Cup (CCCFP) Tester |
| ASTM D 7042 : 2016 : EDT 2 | Standard Test Method for Dynamic Viscosity and Density of Liquids by Stabinger Viscometer (and the Calculation of Kinematic Viscosity) |
| ASTM D 2622 : 1998 | Standard Test Method for Sulfur in Petroleum Products by Wavelength Dispersive X-ray Fluorescence Spectrometry |
| ASTM D 1552 : 2016 | Standard Test Method for Sulfur in Petroleum Products by High Temperature Combustion and Infrared (IR) Detection or Thermal Conducitivity Detection (TCD) |
| ASTM D 5854 : 1996 : R2010 | Standard Practice for Mixing and Handling of Liquid Samples of Petroleum and Petroleum Products |
| ASTM D 240 : 1992 : R1997 : EDT 2 | Standard Test Method for Heat of Combustion of Liquid Hydrocarbon Fuels by Bomb Calorimeter |
| ASTM D 5185 : 2005 | Standard Test Method for Determination of Additive Elements, Wear Metals, and Contaminants in Used Lubricating Oils and Determination of Selected Elements in Base Oils by Inductively Coupled Plasma Atomic Emission Spectrometry (ICP-AES) |
| ASTM D 4629 : 2009 | Standard Test Method for Trace Nitrogen in Liquid Petroleum Hydrocarbons by Syringe/Inlet Oxidative Combustion and Chemiluminescence Detection |
| ASTM D 7042 : 2010 | Standard Test Method for Dynamic Viscosity and Density of Liquids by Stabinger Viscometer (and the Calculation of Kinematic Viscosity) |
| ASTM D 4175 : 2009 : REV A : EDT 4 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
| ASTM D 3828 : 2007 : REV A | Standard Test Methods for Flash Point by Small Scale Closed Cup Tester |
| ASTM D 4175 : 2009 : REV A : EDT 3 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
| ASTM D 1298 : 1999 : R2005 | Standard Test Method for Density, Relative Density (Specific Gravity), or API Gravity of Crude Petroleum and Liquid Petroleum Products by Hydrometer Method |
| ASTM D 129 : 2013-08 | TEST METHOD FOR SULFUR IN PETROLEUM PRODUCTS (GENERAL HIGH PRESSURE DECOMPOSITION DEVICE METHOD) |
| ASTM D 4868 : 2017 : REDLINE | Standard Test Method for Estimation of Net and Gross Heat of Combustion of Hydrocarbon Burner and Diesel Fuels |
| ASTM D 4052 : 2009 | Standard Test Method for Density, Relative Density, and API Gravity of Liquids by Digital Density Meter |
| ASTM D 4057 : 1981 : EDT 2 | Standard Practice for Manual Sampling of Petroleum and Petroleum Products |
| ASTM D 3228 : 2001 | Standard Test Method for Total Nitrogen In Lubricating Oils and Fuel Oils By Modified Kjeldahl Method |
| ASTM D 5185 : 2002 | Standard Test Method for Determination of Additive Elements, Wear Metals, and Contaminants in Used Lubricating Oils and Determination of Selected Elements in Base Oils by Inductively Coupled Plasma Atomic Emission Spectrometry (ICP-AES) |
| ASTM D 1298 : 2012 : REV B : R2017 | Standard Test Method for Density, Relative Density, or API Gravity of Crude Petroleum and Liquid Petroleum Products by Hydrometer Method |
| ASTM D 1298 : 2012 | Standard Test Method for Density, Relative Density (Specific Gravity), or API Gravity of Crude Petroleum and Liquid Petroleum Products by Hydrometer Method |
| ASTM D 5854 : 2019 | Standard Practice for Mixing and Handling of Liquid Samples of Petroleum and Petroleum Products |
| ASTM D 4629 : 1996 | Standard Test Method for Trace Nitrogen in Liquid Petroleum Hydrocarbons by Syringe/Inlet Oxidative Combustion and Chemiluminescence Detection |
| ASTM D 1552 : 2000 | Standard Test Method for Sulfur in Petroleum Products (High-Temperature Method) |
| ASTM D 4868 : 2000 | Standard Test Method for Estimation of Net and Gross Heat of Combustion of Burner and Diesel Fuels |
| ASTM D 1266 : 1987 | Standard Test Method for Sulfur in Petroleum Products (Lamp Method) |
| ASTM D 2622 : 2008 | Standard Test Method for Sulfur in Petroleum Products by Wavelength Dispersive X-ray Fluorescence Spectrometry |
| ASTM D 7042 : 2016 : EDT 1 | Standard Test Method for Dynamic Viscosity and Density of Liquids by Stabinger Viscometer (and the Calculation of Kinematic Viscosity) |
| ASTM D 4175 : 2018 | Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants |
| ASTM D 6448 : 2016 : REDLINE | Standard Specification for Industrial Burner Fuels from Used Lubricating Oils |
| ASTM D 3228 : 2008 | Standard Test Method for Total Nitrogen in Lubricating Oils and Fuel Oils by Modified Kjeldahl Method |
| ASTM D 974 : 2021 | Standard Test Method for Acid and Base Number by Color-Indicator Titration |
| ASTM D 1298 : 1999 : EDT 2 | Standard Test Method for Density, Relative Density (Specific Gravity), or API Gravity of Crude Petroleum and Liquid Petroleum Products by Hydrometer Method |
| ASTM D 5185 : 2018 | Standard Test Method for Multielement Determination of Used and Unused Lubricating Oils and Base Oils by Inductively Coupled Plasma Atomic Emission Spectrometry (ICP-AES) |
| ASTM D 6160 : 1998 : R2013 | Standard Test Method for Determination of Polychlorinated Biphenyls (PCBs) in Waste Materials by Gas Chromatography |
| ASTM D 6448 : 1999 | Standard Specification for Industrial Burner Fuels from Used Lubricating Oils |
| ASTM D 4175 : 2001 : EDT 1 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
| ASTM D 4175 : 2020 : REV B : EDT 1 | Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants |
| ASTM D 1796 : 2004 : R2009 | Standard Test Method for Water and Sediment in Fuel Oils by the Centrifuge Method (Laboratory Procedure) |
| ASTM D 5854 : 1996 : R2005 | Standard Practice for Mixing and Handling of Liquid Samples of Petroleum and Petroleum Products |
| ASTM D 4175 : 2001 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
| ASTM D 4175 : 2005 : EDT 1 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
| CFR 40(PTS260-265) : JUL 2017 | PROTECTION OF ENVIRONMENT - ENVIRONMENTAL PROTECTION AGENCY |
| ASTM D 6448 : 2014 | Standard Specification for Industrial Burner Fuels from Used Lubricating Oils |
| ASTM D 4868 : 1990 : R1995 : EDT 1 | Standard Test Method for Estimation of Net and Gross Heat of Combustion of Burner and Diesel Fuels |
| ASTM D 3228 : 2008 : R2014 | Standard Test Method for Total Nitrogen in Lubricating Oils and Fuel Oils by Modified Kjeldahl Method |
| ASTM D 5291 : 2016 | Standard Test Methods for Instrumental Determination of Carbon, Hydrogen, and Nitrogen in Petroleum Products and Lubricants |
| ASTM D 3245 : 1996 | Standard Test Method for Pumpability of Industrial Fuel Oils |
| ASTM D 7042 : 2020 | Standard Test Method for Dynamic Viscosity and Density of Liquids by Stabinger Viscometer (and the Calculation of Kinematic Viscosity) |
| ASTM D 4175 : 2002 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
| ASTM D 5185 : 2013 : EDT 1 | Standard Test Method for Multielement Determination of Used and Unused Lubricating Oils and Base Oils by Inductively Coupled Plasma Atomic Emission Spectrometry (ICP-AES) |
| ASTM D 93 : 1990 : EDT 1 | Standard Test Methods for Flash Point by Pensky-Martens Closed Tester |
| ASTM D 6450 : 1999 | Standard Test Method for Flash Point by Continuously Closed Cup (CCCFP) Tester |
| ASTM D 6160 : 1998 : R2017 | Standard Test Method for Determination of Polychlorinated Biphenyls (PCBs) in Waste Materials by Gas Chromatography |
| ASTM D 3828 : 2012 | Standard Test Methods for Flash Point by Small Scale Closed Cup Tester |
| ASTM D 445 : 1988 | Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and the Calculation of Dynamic Viscosity) |
| ASTM D 5291 : 2002 | Standard Test Methods for Instrumental Determination of Carbon, Hydrogen, and Nitrogen in Petroleum Products and Lubricants |
| ASTM D 1298 : 1999 | Standard Test Method for Density, Relative Density (Specific Gravity), or API Gravity of Crude Petroleum and Liquid Petroleum Products by Hydrometer Method |
| ISO 8217:2017 | Petroleum products Fuels (class F) Specifications of marine fuels |
| ASTM D 5384 : 2011 | Standard Test Methods for Chlorine in Used Petroleum Products (Field Test Kit Method) |
| ASTM D 6160 : 1998 : R2008 | Standard Test Method for Determination of Polychlorinated Biphenyls (PCBs) in Waste Materials by Gas Chromatography |
| ASTM D 4057 : 2006 | Standard Practice for Manual Sampling of Petroleum and Petroleum Products |
| ASTM D 4294 : 2008 | Standard Test Method for Sulfur in Petroleum and Petroleum Products by Energy Dispersive X-ray Fluorescence Spectrometry |
| ASTM D 1796 : 1997 | Standard Test Method for Water and Sediment in Fuel Oils by the Centrifuge Method (Laboratory Procedure) |
| ASTM D 4175 : 2015 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
| ASTM D 4175 : 2002 : REV A : EDT 2 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
| ASTM D 4177 : 2015 | Standard Practice for Automatic Sampling of Petroleum and Petroleum Products |
| ASTM D 7042 : 2011 : REV A | Standard Test Method for Dynamic Viscosity and Density of Liquids by Stabinger Viscometer (and the Calculation of Kinematic Viscosity) |
| ASTM D 4052 : 2011 | Standard Test Method for Density, Relative Density, and API Gravity of Liquids by Digital Density Meter |
| ASTM D 4052 : 2016 | Standard Test Method for Density, Relative Density, and API Gravity of Liquids by Digital Density Meter |
| ASTM D 4057 : 2012 | Standard Practice for Manual Sampling of Petroleum and Petroleum Products |
| ASTM D 5384 : 2014 : R2019 | Standard Test Methods for Chlorine in Used Petroleum Products (Field Test Kit Method) |
| ASTM D 3828 : 2016 : REV A | Standard Test Methods for Flash Point by Small Scale Closed Cup Tester |
| ASTM D 2983 : 2020 | Standard Test Method for Low-Temperature Viscosity of Automatic Transmission Fluids, Hydraulic Fluids, and Lubricants using a Rotational Viscometer |
| ASTM D 5185 : 2013 | Standard Test Method for Multielement Determination of Used and Unused Lubricating Oils and Base Oils by Inductively Coupled Plasma Atomic Emission Spectrometry (ICP-AES) |
| ASTM D 1796 : 1997 : EDT 1 | Standard Test Method for Water and Sediment in Fuel Oils by the Centrifuge Method (Laboratory Procedure) |
| ASTM D 664 : 1995 | Standard Test Method for Acid Number of Petroleum Products by Potentiometric Titration |
| ASTM D 2622 : 2003 | Standard Test Method for Sulfur in Petroleum Products by Wavelength Dispersive X-ray Fluorescence Spectrometry |
| ASTM D 4294 : 2008 : REV A | Standard Test Method for Sulfur in Petroleum and Petroleum Products by Energy Dispersive X-ray Fluorescence Spectrometry |
| ASTM D 4175 : 2009 : REV A : EDT 5 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
| ASTM D 4175 : 2016 : REV C | Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants |
| ASTM D 4175 : 2015 : REV B | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
| ASTM D 56 : 2016 : REV A | Standard Test Method for Flash Point by Tag Closed Cup Tester |
| ASTM D 4294 : 2002 | Standard Test Method for Sulfur in Petroleum Products by Energy-Dispersive X-Ray Fluorescence Spectroscopy |
| ASTM D 4175 : 2015 : REV A | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
| ASTM D 1552 : 2016 : EDT 1 | Standard Test Method for Sulfur in Petroleum Products by High Temperature Combustion and Infrared (IR) Detection or Thermal Conductivity Detection (TCD) |
| ASTM D 5384 : 2014 | Standard Test Methods for Chlorine in Used Petroleum Products (Field Test Kit Method) |
| ASTM D 1298 : 1999 : EDT 1 | Standard Test Method for Density, Relative Density (Specific Gravity), or API Gravity of Crude Petroleum and Liquid Petroleum Products by Hydrometer Method |
| ASTM D 7042 : 2004 | Standard Test Method for Dynamic Viscosity and Density of Liquids by Stabinger Viscometer (and the Calculation of Kinematic Viscosity) |
| ASTM D 1552 : 2007 | Standard Test Method for Sulfur in Petroleum Products (High-Temperature Method) |
| ASTM D 4868 : 2017 | Standard Test Method for Estimation of Net and Gross Heat of Combustion of Hydrocarbon Burner and Diesel Fuels |
| ASTM D 445 : 2019 : REV A | Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity) |
| ASTM D 1552 : 1995 | Standard Test Method for Sulfur in Petroleum Products (High-Temperature Method) |
| ASTM D 4175 : 2009 : REV A | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
| ASTM D 4629 : 2002 | Standard Test Method for Trace Nitrogen in Liquid Petroleum Hydrocarbons by Syringe/Inlet Oxidative Combustion and Chemiluminescence Detection |
| ASTM D 2983 : 2004 : REV A | Standard Test Method for Low-Temperature Viscosity of Lubricants Measured by Brookfield Viscometer |
| ASTM D 4865 : 1998 | Standard Guide for Generation and Dissipation of Static Electricity in Petroleum Fuel Systems |
| ASTM D 4175 : 2016 : REV B | Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants |
| ASTM D 5291 : 2002 : R2007 | Standard Test Methods for Instrumental Determination of Carbon, Hydrogen, and Nitrogen in Petroleum Products and Lubricants |
| ASTM D 7042 : 2019 | Standard Test Method for Dynamic Viscosity and Density of Liquids by Stabinger Viscometer (and the Calculation of Kinematic Viscosity) |
| ASTM D 4177 : 1995 : R2010 | Standard Practice for Automatic Sampling of Petroleum and Petroleum Products |
| CFR 40(PTS700-789) : JUL 2016 | PROTECTION OF ENVIRONMENT - ENVIRONMENTAL PROTECTION AGENCY |
| ASTM D 1552 : 2015 | Standard Test Method for Sulfur in Petroleum Products by High Temperature Combustion and IR Detection |
| ASTM D 4175 : 2002 : REV A : EDT 1 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
| ASTM D 4175 : 2008 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
| ASTM D 1552 : 2001 | Standard Test Method for Sulfur in Petroleum Products (High-Temperature Method) |
| ASTM D 3228 : 2003 | Standard Test Method for Total Nitrogen in Lubricating Oils and Fuel Oils by Modified Kjeldahl Method |
| ASTM D 3228 : 1996 | Standard Test Method for Total Nitrogen In Lubricating Oils and Fuel Oils By Modified Kjeldahl Method |
| ASTM D 4175 : 2002 : REV A | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
| ASTM D 4294 : 2016 : EDT 1 | Standard Test Method for Sulfur in Petroleum and Petroleum Products by Energy Dispersive X-ray Fluorescence Spectrometry |
| ASTM D 5384 : 1995 : R2000 : EDT 1 | Standard Test Methods for Chlorine in Used Petroleum Products (Field Test Kit Method) |
| ASTM D 4177 : 1995 : R2000 | Standard Practice for Automatic Sampling of Peroleum and Petroleum Products |
| ASTM D 1552 : 2008 : R2014 : EDT 1 | Standard Test Method for Sulfur in Petroleum Products (High-Temperature Method) |
| ASTM D 4175 : 2000 : EDT 1 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
| ASTM D 93 : 2016-07 | TEST METHODS FOR FLASH POINT BY PENSKY-MARTENS CLOSED CUP TESTER |
| ASTM D 4868 : 2000 : R2010 | Standard Test Method for Estimation of Net and Gross Heat of Combustion of Burner and Diesel Fuels |
| ASTM D 4175 : 2016 : REV A | Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants |
| ASTM D 6450 : 2005 | Standard Test Method for Flash Point by Continuously Closed Cup (CCCFP) Tester |
| ASTM D 5854 : 1996 : R2000 | Standard Practice for Mixing and Handling of Liquid Samples of Petroleum and Petroleum Products |
| ASTM D 7042 : 2012 : REV A | Standard Test Method for Dynamic Viscosity and Density of Liquids by Stabinger Viscometer (and the Calculation of Kinematic Viscosity) |
| ASTM D 4294 : 2008 : REV A : EDT 1 | Standard Test Method for Sulfur in Petroleum and Petroleum Products by Energy Dispersive X-ray Fluorescence Spectrometry |
| ASTM D 4629 : 2017 | Standard Test Method for Trace Nitrogen in Liquid Hydrocarbons by Syringe/Inlet Oxidative Combustion and Chemiluminescence Detection |
| ASTM D 4052 : 1996 | Standard Test Method for Density and Relative Density of Liquids by Digital Density Meter |
| ASTM D 6450 : 2016 : REV A : R2021 | Standard Test Method for Flash Point by Continuously Closed Cup (CCCFP) Tester |
| ASTM D 4294 : 1998 | Standard Test Method for Sulfur in Petroleum Products by Energy-Dispersive X-Ray Fluorescence Spectroscopy |
| ASTM D 56 : 2021 | Standard Test Method for Flash Point by Tag Closed Cup Tester |
| ASTM D 4629 : 2012 | Standard Test Method for Trace Nitrogen in Liquid Petroleum Hydrocarbons by Syringe/Inlet Oxidative Combustion and Chemiluminescence Detection |
| ASTM D 3828 : 2005 | Standard Test Methods for Flash Point by Small Scale Closed Cup Tester |
| ASTM D 6450 : 2005 : R2010 | Standard Test Method for Flash Point by Continuously Closed Cup (CCCFP) Tester |
| ASTM D 4175 : 2019 : EDT 1 | Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants |
| ASTM D 2983 : 2015 | Standard Test Method for Low-Temperature Viscosity of Lubricants Measured by Brookfield Viscometer<rangeref></rangeref > |
| ASTM D 6448 : 2004 | Standard Specification for Industrial Burner Fuels from Used Lubricating Oils |
| ASTM D 2983 : 2009 | Standard Test Method for Low-Temperature Viscosity of Lubricants Measured by Brookfield Viscometer |
| ASTM D 2622 : 2010 | Standard Test Method for Sulfur in Petroleum Products by Wavelength Dispersive X-ray Fluorescence Spectrometry |
| ASTM D 7042 : 2016 : EDT 3 | Standard Test Method for Dynamic Viscosity and Density of Liquids by Stabinger Viscometer (and the Calculation of Kinematic Viscosity) |
| ASTM D 6448 : 2014 : EDT 1 | Standard Specification for Industrial Burner Fuels from Used Lubricating Oils |
| ASTM D 396 : 2021 | Standard Specification for Fuel Oils |
| ASTM D 5185 : 2009 | Standard Test Method for Determination of Additive Elements, Wear Metals, and Contaminants in Used Lubricating Oils and Determination of Selected Elements in Base Oils by Inductively Coupled Plasma Atomic Emission Spectrometry (ICP-AES) |
| ASTM D 4629 : 2012 : R2017 | Standard Test Method for Trace Nitrogen in Liquid Petroleum Hydrocarbons by Syringe/Inlet Oxidative Combustion and Chemiluminescence Detection |
| ASTM D 5291 : 2001 | Standard Test Methods for Instrumental Determination of Carbon, Hydrogen, and Nitrogen in Petroleum Products and Lubricants |
| ASTM D 93 : 2000 | Standard Test Methods for Flash-Point by Pensky-Martens Closed Cup Tester |
| ASTM D 445 : 2001 | Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (the Calculation of Dynamic Viscosity) |
| ASTM D 2983 : 2019 : EDT 1 | Standard Test Method for Low-Temperature Viscosity of Automatic Transmission Fluids, Hydraulic Fluids, and Lubricants using a Rotational Viscometer |
| ASTM D 396 : 2009 | Standard Specification for Fuel Oils |
| ASTM D 445 : 2021 | Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity) |
| ASTM D 4629 : 2008 | Standard Test Method for Trace Nitrogen in Liquid Petroleum Hydrocarbons by Syringe/Inlet Oxidative Combustion and Chemiluminescence Detection |
| ASTM D 5291 : 1996 | Standard Test Methods for Instrumental Determination of Carbon, Hydrogen, and Nitrogen in Petroleum Products and Lubricants |
| ASTM D 93 : 1985 | Standard Test Method for Flash Point by Pensky-Martens Closed Tester |
| ASTM D 4868 : 2000 : R2005 | Standard Test Method for Estimation of Net and Gross Heat of Combustion of Burner and Diesel Fuels |
| ASTM D 1796 : 2011 : R2016 | Standard Test Method for Water and Sediment in Fuel Oils by the Centrifuge Method (Laboratory Procedure) |
| ASTM D 2622 : 2007 | Standard Test Method for Sulfur in Petroleum Products by Wavelength Dispersive X-ray Fluorescence Spectrometry |
| ASTM D 4175 : 2017 : REV A | Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants |
| ASTM D 4629 : 2010 | Standard Test Method for Trace Nitrogen in Liquid Petroleum Hydrocarbons by Syringe/Inlet Oxidative Combustion and Chemiluminescence Detection |
| ASTM D 2983 : 2001 | Standard Test Method for Low-Temperature Viscosity of Lubricants Measured by Brookfield Viscometer |
| ASTM D 3828 : 2009 | Standard Test Methods for Flash Point by Small Scale Closed Cup Tester |
| ASTM D 2622 : 1994 | Standard Test Method for Sulfur in Petroleum Products by X-Ray Spectrometry |
| ASTM D 7042 : 2012 : EDT 1 | Standard Test Method for Dynamic Viscosity and Density of Liquids by Stabinger Viscometer (and the Calculation of Kinematic Viscosity) |
| ASTM D 4175 : 2009 : REV A : EDT 2 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
| ASTM D 1552 : 2008 | Standard Test Method for Sulfur in Petroleum Products (High-Temperature Method) |
| ASTM D 2622 : 2005 | Standard Test Method for Sulfur in Petroleum Products by Wavelength Dispersive X-ray Fluorescence Spectrometry |
| ASTM D 4177 : 2016 | Standard Practice for Automatic Sampling of Petroleum and Petroleum Products |
| ASTM D 5185 : 2002 : EDT 1 | Standard Test Method for Determination of Additive Elements, Wear Metals, and Contaminants in Used Lubricating Oils and Determination of Selected Elements in Base Oils by Inductively Coupled Plasma Atomic Emission Spectrometry (ICP-AES) |
| ASTM D 4294 : 2003 | Standard Test Method for Sulfur in Petroleum and Petroleum Products by Energy-Dispersive X-Ray Fluorescence Spectrometry |
| ASTM D 2983 : 2004 | Standard Test Method for Low-Temperature Viscosity of Lubricants Measured by Brookfield Viscometer |
| ASTM D 2983 : 2003 | Standard Test Method for Low-Temperature Viscosity of Lubricants Measured by Brookfield Viscometer |
| ASTM D 4177 : 1995 : R2005 | Standard Practice for Automatic Sampling of Petroleum and Petroleum Products |
| ASTM D 4175 : 2018 : EDT 1 | Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants |
| ASTM D 1298 : 1985 : R1990 : EDT 1 | Standard Practice for Density, Relative Density (Specific Gravity), or API Gravity of Crude Petroleum and Liquid Petroleum Products by Hydrometer Method |
| ASTM D 4175 : 2016 | Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants |
| ASTM D 56 : 1987 | Standard Test Method for Flash Point by Tag Closed Tester |
| ASTM D 5291 : 2016 : REDLINE | Standard Test Methods for Instrumental Determination of Carbon, Hydrogen, and Nitrogen in Petroleum Products and Lubricants |
| ASTM D 4294 : 2016 | Standard Test Method for Sulfur in Petroleum and Petroleum Products by Energy Dispersive X-ray Fluorescence Spectrometry |
| ASTM D 1796 : 1997 : R2002 | Standard Test Method for Water and Sediment in Fuel Oils by the Centrifuge Method (Laboratory Procedure) |
| ASTM D 2983 : 1987 : R1993 | Standard Test Method for Low-Temperature Viscosity of Lubricants Measured by Brookfield Viscometer |
| ASTM D 5854 : 2019 : REV A | Standard Practice for Mixing and Handling of Liquid Samples of Petroleum and Petroleum Products |
| ASTM D 7042 : 2016 | Standard Test Method for Dynamic Viscosity and Density of Liquids by Stabinger Viscometer (and the Calculation of Kinematic Viscosity) |
| ASTM D 240 : 2017 : REDLINE | Standard Test Method for Heat of Combustion of Liquid Hydrocarbon Fuels by Bomb Calorimeter |
| ASTM D 5185 : 2002 : EDT 2 | Standard Test Method for Determination of Additive Elements, Wear Metals, and Contaminants in Used Lubricating Oils and Determination of Selected Elements in Base Oils by Inductively Coupled Plasma Atomic Emission Spectrometry (ICP-AES) |
| ASTM D 2622 : 2016 : REDLINE | Standard Test Method for Sulfur in Petroleum Products by Wavelength Dispersive X-ray Fluorescence Spectrometry |
| ASTM D 4052 : 2015 | Standard Test Method for Density, Relative Density, and API Gravity of Liquids by Digital Density Meter |
| ASTM D 1796 : 2004 | Standard Test Method for Water and Sediment in Fuel Oils by the Centrifuge Method (Laboratory Procedure) |
| ASTM D 4057 : 1995 : R2000 | Standard Practice for Manual Sampling of Petroleum and Petroleum Products |
| ASTM D 1796 : 2011 : EDT 1 | Standard Test Method for Water and Sediment in Fuel Oils by the Centrifuge Method (Laboratory Procedure) |
| ASTM D 1552 : 2016 : R2021 | Standard Test Method for Sulfur in Petroleum Products by High Temperature Combustion and Infrared (IR) Detection or Thermal Conductivity Detection (TCD) |
| ASTM D 4175 : 2017 | Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants |
| ASTM D 1796 : 1983 : R1990 : EDT 1 | Standard Test Method for Water and Sediment in Fuel Oils by the Centrifuge Method (Laboratory Procedure) |
| ASTM D 5384 : 1995 : R2005 | Standard Test Methods for Chlorine in Used Petroleum Products (Field Test Kit Method) |
| ASTM D 93 : 1997 | Standard Test Methods for Flash-Point by Pensky-Martens Closed Cup Tester |
| ASTM D 4175 : 2019 | Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants |
| ASTM D 1266 : 2007 | Standard Test Method for Sulfur in Petroleum Products (Lamp Method) |
| ASTM D 4177 : 2015 : REV A | Standard Practice for Automatic Sampling of Petroleum and Petroleum Products |
| ASTM D 4057 : 2006 : R2011 | Standard Practice for Manual Sampling of Petroleum and Petroleum Products |
| ASTM D 1552 : 1983 | Standard Test Method for Sulfur in Petroleum Products (High-Temperature Method) |
| ASTM D 4175 : 2015 : REV B : EDT 1 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
| ASTM D 6448 : 2009 | Standard Specification for Industrial Burner Fuels from Used Lubricating Oils |
| ASTM D 5291 : 2009 | Standard Test Methods for Instrumental Determination of Carbon, Hydrogen, and Nitrogen in Petroleum Products and Lubricants |
| ASTM D 6160 : 1998 : R2003 : EDT 1 | Standard Test Method for Determination of Polychlorinated Biphenyls (PCBs) in Waste Materials by Gas Chromatography |
| ASTM D 3228 : 2005 | Standard Test Method for Total Nitrogen in Lubricating Oils and Fuel Oils by Modified Kjeldahl Method |
| ASTM D 3828 : 2016 | Standard Test Methods for Flash Point by Small Scale Closed Cup Tester |
| ASTM D 5854 : 1996 : R2015 | Standard Practice for Mixing and Handling of Liquid Samples of Petroleum and Petroleum Products |
| ASTM D 4052 : 2018 | Standard Test Method for Density, Relative Density, and API Gravity of Liquids by Digital Density Meter |
| ASTM D 1266 : 2018 | Standard Test Method for Sulfur in Petroleum Products (Lamp Method) |
| ASTM D 4294 : 1990 : R1998 : EDT 1 | Standard Test Method for Sulfur in Petroleum Products by Energy-Dispersive X-Ray Fluorescence Spectroscopy |
| ASTM D 4175 : 2008 : REV B | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
| ASTM D 2622 : 2016 | Standard Test Method for Sulfur in Petroleum Products by Wavelength Dispersive X-ray Fluorescence Spectrometry |
| ASTM D 7042 : 2014 | Standard Test Method for Dynamic Viscosity and Density of Liquids by Stabinger Viscometer (and the Calculation of Kinematic Viscosity) |
| ASTM D 2983 : 2016 | Standard Test Method for Low-Temperature Viscosity of Automatic Transmission Fluids, Hydraulic Fluids, and Lubricants using a Rotational Viscometer |
| ASTM D 3828 : 1997 | Standard Test Methods for Flash Point by Small Scale Closed Tester |
| ASTM D 6450 : 2016 | Standard Test Method for Flash Point by Continuously Closed Cup (CCCFP) Tester |
£62.61
Excluding VAT
GBP
CAD
CHF
CNY
DKK
EUR
GBP
HKD
IDR
INR
JPY
KRW
MXN
NOK
NZD
SEK
SGD
USD
ZAR
Hardcopy - English
PDF - English
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.