Name: ASTM D 6823 : 2008 : R2021
Brand: ASTM
Price: 52.59 GBP

Standard Specification for Commercial Boiler Fuels With Used Lubricating Oils

Available format(s)

Hardcopy , PDF

Language(s)

English

Published date

16-11-2021

Publisher

American Society for Testing and Materials

1.1This specification covers four grades of fuel oil made of at least 25 % used lubricating oils. The four grades of fuel are intended for use in various types of fuel-oil-burning industrial equipment and commercial boilers under various climatic and operating conditions. These fuels are not intended for use in residential heaters.

1.1.1Grades RFC4, RFC5L, RFC5H and RFC6 are used lubricating oil blends of increasing viscosity, with or without middle distillate or residual fuel oil, or both, that are intended for use in industrial burners and commercial boilers equipped to handle these types of fuels. This specification is for applications where Specification D6448 would not meet the performance or other requirements of the burner or boiler in question.

Note 1:For information on the significance of the terminology and test methods used in this specification, see Appendix X1.

1.2This specification is for use in contracts for the purchase of fuel oils derived from used lubricating oil and for the guidance of consumers of such fuels. This specification does not address the frequency with which any particular test must be run.

1.3Nothing in this specification shall preclude observance of national or local regulations which can be more restrictive. In some jurisdictions, used oil is considered a hazardous waste and fuels derived from used oil are required to meet certain criteria before use as a fuel.

Note 2:For United States federal requirements imposed on used oil generators, transporters and transfer facilities, reprocessors, marketers, and burners, see 40 CFR Part 279.

Note 3:The generation and dissipation of static electricity can create problems in the handling of distillate burner fuel oils. For more information on the subject, see Guide D4865.

1.4The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.

1.4.1Exception—Table 1 and Table X1.1 include inch-pound values in parentheses for information only.

1.5This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Committee	D 02
DocumentType	Standard
Pages	7
PublisherName	American Society for Testing and Materials
Status	Current
Supersedes	ASTM D 6823 : 2008 : R2013

ASTM D 7666 : 2012 : R2019

Standard Specification for Triglyceride Burner Fuel

ASTM D 4057 : 2019	Standard Practice for Manual Sampling of Petroleum and Petroleum Products
ASTM D 129 : 2018	Standard Test Method for Sulfur in Petroleum Products (General High Pressure Decomposition Device Method) (Withdrawn 2023)
ASTM D 5291 : 2021	Standard Test Methods for Instrumental Determination of Carbon, Hydrogen, and Nitrogen in Petroleum Products and Lubricants
ASTM D 4865 : 2019	Standard Guide for Generation and Dissipation of Static Electricity in Petroleum Fuel Systems
ASTM D 974 : 2014 : EDT 2	Standard Test Method for Acid and Base Number by Color-Indicator Titration
ASTM D 4865 : 2023	Standard Guide for Generation and Dissipation of Static Electricity in Petroleum Fuel Systems
ASTM D 6448 : 2016	Standard Specification for Industrial Burner Fuels from Used Lubricating Oils
ASTM D 664 : 2017 : REV A	Standard Test Method for Acid Number of Petroleum Products by Potentiometric Titration
ASTM D 6448 : 2016 : R2022	Standard Specification for Industrial Burner Fuels from Used Lubricating Oils
ASTM D 482 : 2013	Standard Test Method for Ash from Petroleum Products
ASTM D 4052 : 2018 : REV A	Standard Test Method for Density, Relative Density, and API Gravity of Liquids by Digital Density Meter
ASTM D 1298 : 2012 : REV B : R2017 : EDT 1	Standard Test Method for Density, Relative Density, or API Gravity of Crude Petroleum and Liquid Petroleum Products by Hydrometer Method
ASTM D 473 : 2007 : R2017 : EDT 1	Standard Test Method for Sediment in Crude Oils and Fuel Oils by the Extraction Method
ASTM D 3828 : 2016 : REV A : R2021	Standard Test Methods for Flash Point by Small Scale Closed Cup Tester
ASTM D 4175 : 2022	Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants
ASTM D 974 : 2022	Standard Test Method for Acid and Base Number by Color-Indicator Titration
ASTM D 473 : 2022	Standard Test Method for Sediment in Crude Oils and Fuel Oils by the Extraction Method
ASTM D 1298 : 2012 : REV B : R2017	Standard Test Method for Density, Relative Density, or API Gravity of Crude Petroleum and Liquid Petroleum Products by Hydrometer Method
ASTM D 5854 : 2019	Standard Practice for Mixing and Handling of Liquid Samples of Petroleum and Petroleum Products
ASTM D 445 : 2021 : EDT 2	Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity)
ASTM D 93 : 2019	Standard Test Methods for Flash Point by Pensky-Martens Closed Cup Tester
ASTM D 974 : 2021	Standard Test Method for Acid and Base Number by Color-Indicator Titration
ASTM D 445 : 2017 : REV A	Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity)
ASTM D 4175 : 2020 : REV B : EDT 1	Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants
ASTM D 4175 : 2022 : REV A	Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants
ASTM D 5291 : 2016	Standard Test Methods for Instrumental Determination of Carbon, Hydrogen, and Nitrogen in Petroleum Products and Lubricants
ASTM D 1796 : 2022	Standard Test Method for Water and Sediment in Fuel Oils by the Centrifuge Method (Laboratory Procedure)
ASTM D 4175 : 2023	Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants
ASTM D 1552 : 2023	Standard Test Method for Sulfur in Petroleum Products by High Temperature Combustion and Infrared (IR) Detection or Thermal Conductivity Detection (TCD)
ASTM D 3228 : 2022	Standard Test Method for Total Nitrogen in Lubricating Oils and Fuel Oils by Modified Kjeldahl Method
ASTM D 95 : 2013 : R2018	Standard Test Method for Water in Petroleum Products and Bituminous Materials by Distillation
ASTM D 56 : 2021 : REV A	Standard Test Method for Flash Point by Tag Closed Cup Tester
ASTM D 7042 : 2021	Standard Test Method for Dynamic Viscosity and Density of Liquids by Stabinger Viscometer (and the Calculation of Kinematic Viscosity)
ASTM D 3828 : 2016 : REV A	Standard Test Methods for Flash Point by Small Scale Closed Cup Tester
ASTM D 4175 : 2022 : REV A : EDT 1	Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants
ASTM D 56 : 2016 : REV A	Standard Test Method for Flash Point by Tag Closed Cup Tester
ASTM D 3228 : 2020	Standard Test Method for Total Nitrogen in Lubricating Oils and Fuel Oils by Modified Kjeldahl Method
ASTM D 4868 : 2017	Standard Test Method for Estimation of Net and Gross Heat of Combustion of Hydrocarbon Burner and Diesel Fuels
ASTM D 445 : 2019 : REV A	Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity)
ASTM D 4177 : 2022	Standard Practice for Automatic Sampling of Petroleum and Petroleum Products
ASTM D 97 : 2017 : REV B	Standard Test Method for Pour Point of Petroleum Products
ASTM D 4294 : 2016 : EDT 1	Standard Test Method for Sulfur in Petroleum and Petroleum Products by Energy Dispersive X-ray Fluorescence Spectrometry
ASTM D 2983 : 2021	Standard Test Method for Low-Temperature Viscosity of Automatic Transmission Fluids, Hydraulic Fluids, and Lubricants using a Rotational Viscometer
ASTM D 445 : 2019	Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity)
ASTM D 4175 : 2023 : EDT 1	Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants
ASTM D 4175 : 2023 : REV A	Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants
ASTM D 4175 : 2022 : EDT 1	Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants
ASTM D 2983 : 2022	Standard Test Method for Low-Temperature Viscosity of Automatic Transmission Fluids, Hydraulic Fluids, and Lubricants using a Rotational Viscometer
ASTM D 4294 : 2021	Standard Test Method for Sulfur in Petroleum and Petroleum Products by Energy Dispersive X-ray Fluorescence Spectrometry
ASTM D 2622 : 2021	Standard Test Method for Sulfur in Petroleum Products by Wavelength Dispersive X-ray Fluorescence Spectrometry
ASTM D 97 : 2017 : REV B : R2022	Standard Test Method for Pour Point of Petroleum Products
ASTM D 664 : 2011 : REV A	Standard Test Method for Acid Number of Petroleum Products by Potentiometric Titration
ASTM D 445 : 2024	Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity)
ASTM D 445 : 2021	Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity)
ASTM D 1796 : 2011 : R2016	Standard Test Method for Water and Sediment in Fuel Oils by the Centrifuge Method (Laboratory Procedure)
ASTM D 4057 : 2022	Standard Practice for Manual Sampling of Petroleum and Petroleum Products
ASTM D 56 : 2022	Standard Test Method for Flash Point by Tag Closed Cup Tester
ASTM D 4052 : 2022	Standard Test Method for Density, Relative Density, and API Gravity of Liquids by Digital Density Meter
ASTM D 7042 : 2021 : REV A	Standard Test Method for Dynamic Viscosity and Density of Liquids by Stabinger Viscometer (and the Calculation of Kinematic Viscosity)
ASTM D 4177 : 2020	Standard Practice for Automatic Sampling of Petroleum and Petroleum Products
ASTM D 445 : 2018	Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity)
ASTM D 2983 : 2023	Standard Test Method for Low-Temperature Viscosity of Automatic Transmission Fluids, Hydraulic Fluids, and Lubricants using a Rotational Viscometer
ASTM D 445 : 2021 : EDT 1	Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity)
ASTM D 4177 : 2022 : EDT 1	Standard Practice for Automatic Sampling of Petroleum and Petroleum Products
ASTM D 1552 : 2016 : R2021	Standard Test Method for Sulfur in Petroleum Products by High Temperature Combustion and Infrared (IR) Detection or Thermal Conductivity Detection (TCD)
ASTM D 95 : 2023	Standard Test Method for Water in Petroleum Products and Bituminous Materials by Distillation
ASTM D 445 : 2023	Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity)
ASTM D 2622 : 2016	Standard Test Method for Sulfur in Petroleum Products by Wavelength Dispersive X-ray Fluorescence Spectrometry
ASTM D 93 : 2018	Standard Test Methods for Flash Point by Pensky-Martens Closed Cup Tester