ASTM D 696 : 2016 : REDLINE
Current
Current
The latest, up-to-date edition.
Standard Test Method for Coefficient of Linear Thermal Expansion of Plastics Between −30°C and 30°C with a Vitreous Silica Dilatometer
Available format(s)
PDF
Language(s)
English
Published date
01-04-2016
CONTAINED IN VOL. 08.01, 2017 Includes determination of the coefficient of linear thermal expansion for plastic materials having coefficients of expansion greater than 1[mu]m/(m. degrees C) by use of a vitreous silica dilatometer.
1.1This test method covers determination of the coefficient of linear thermal expansion for plastic materials having coefficients of expansion greater than 1 µm/(m.°C) by use of a vitreous silica dilatometer. At the test temperatures and under the stresses imposed, the plastic materials shall have a negligible creep or elastic strain rate or both, insofar as these properties would significantly affect the accuracy of the measurements.
1.1.1Test Method E228 shall be used for temperatures other than −30°C to 30°C.
1.1.2This test method shall not be used for measurements on materials having a very low coefficient of expansion (less than 1 µm/(m.°C). For materials having very low coefficient of expansion, interferometer or capacitance techniques are recommended.
1.1.3Alternative technique commonly used for measuring this property is thermomechanical analysis as described in Test Method E831, which permits measurement of this property over a scanned temperature range.
1.2The thermal expansion of a plastic is composed of a reversible component on which are superimposed changes in length due to changes in moisture content, curing, loss of plasticizer or solvents, release of stresses, phase changes and other factors. This test method is intended for determining the coefficient of linear thermal expansion under the exclusion of these factors as far as possible. In general, it will not be possible to exclude the effect of these factors completely. For this reason, the test method can be expected to give only an approximation to the true thermal expansion.
1.3The values stated in SI units are to be regarded as standard. The values in parentheses are for information only.
1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Note 1:There is no known ISO equivalent to this standard.
| Committee |
D 20
|
| DocumentType |
Redline
|
| Pages |
6
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Current
|
| MIL-C-47224 Revision B:1993 | COMPOUND, MOLDING, TRANSFER, EPOXY RESIN, SINGLE COMPONENT |
| PREN 13491 : DRAFT 2016 | GEOSYNTHETIC BARRIERS - CHARACTERISTICS REQUIRED FOR USE AS A FLUID BARRIER IN THE CONSTRUCTION OF TUNNELS AND ASSOCIATED UNDERGROUND STRUCTURES |
| 16/30338114 DC : 0 | BS EN 13361 - GEOSYNTHETIC BARRIERS - CHARACTERISTICS REQUIRED FOR USE IN THE CONSTRUCTION OF RESERVOIRS AND DAMS |
| CSA S807 : 2010 | SPECIFICATION FOR FIBRE-REINFORCED POLYMERS |
| MIL-PRF-5425 Revision E:1998 | PLASTIC SHEET, ACRYLIC, HEAT RESISTANT |
| 16/30338123 DC : 0 | BS EN 16993 - GEOSYNTHETIC BARRIERS - CHARACTERISTICS REQUIRED FOR USE IN THE CONSTRUCTION OF STORAGE LAGOONS, SECONDARY CONTAINMENT (ABOVE AND BELOW GROUND) AND OTHER CONTAINMENT APPLICATIONS FOR CHEMICALS, POLLUTED WATER AND PRODUCED LIQUIDS |
| 13/30290552 DC : 0 | BS EN 4691-1 AEROSPACE SERIES - TIE ROD WITH INTEGRATED BOLTS - PART 1: TECHNICAL SPECIFICATION |
| 12/30267857 DC : 0 | BS EN 15382 - GEOSYNTHETIC BARRIERS - CHARACTERISTICS REQUIRED FOR USE IN TRANSPORTATION INFRASTRUCTURE |
| 12/30267848 DC : 0 | BS EN 13362 - GEOSYNTHETIC BARRIERS - CHARACTERISTICS REQUIRED FOR USE IN THE CONSTRUCTION OF CANALS |
| ASTM D 5476 : 1999 | Standard Classification System for Thermoplastic Polyurethane Materials (TPU) (Withdrawn 2005) |
| 16/30338304 DC : 0 | BS ISO/ASTM 52903-1 - ADDITIVE MANUFACTURING - STANDARD SPECIFICATION FOR MATERIAL EXTRUSION BASED ADDITIVE MANUFACTURING OF PLASTIC MATERIALS - PART 1: FEEDSTOCK MATERIALS |
| ASTM F 942 : 2002 | Standard Guide for Selection of Test Methods for Interlayer Materials for Aerospace Transparent Enclosures |
| MIL-P-46185 Base Document:1983 | PLASTIC MOLDING & EXTRUSION MATERIALS, POLYETHERSULFONE |
| ASTM F 1876 : 1998 | Standard Specification for Polyetherketoneetherketoneketone (PEKEKK) Resins for Surgical Implant Applications |
| ASTM E 228 : 2017 : REDLINE | Standard Test Method for Linear Thermal Expansion of Solid Materials With a Push-Rod Dilatometer |
| MIL P 8184 : E | PLASTIC SHEET, ACRYLIC, MODIFIED |
| API 17U : 2015 | RECOMMENDED PRACTICE FOR WET AND DRY THERMAL INSULATION OF SUBSEA FLOWLINES AND EQUIPMENT |
| UNE-EN 13491:2013 | Geosynthetic barriers - Characteristics required for use as a fluid barrier in the construction of tunnels and associated underground structures |
| SAE J 1568 : 2012 | MATERIALS FOR PLASTIC PISTONS FOR HYDRAULIC DISC BRAKE CYLINDERS |
| BS EN 13493:2013 | Geosynthetic barriers. Characteristics required for use in the construction of solid waste storage and disposal sites |
| UNE-EN 15382:2013 | Geosynthetic barriers - Characteristics required for use in transportation infrastructure |
| BS EN 15382:2013 | Geosynthetic barriers. Characteristics required for use in transportation infrastructure |
| EN 13491:2018 | Geosynthetic barriers - Characteristics required for use in the construction of tunnels and associated underground structures |
| ASTM D 3105 : 2017 : REDLINE | Standard Index of Methods for Testing Elastomeric and Plastomeric Roofing and Waterproofing Materials |
| ASTM F 942 : 2002 : R2008 | Standard Guide for Selection of Test Methods for Interlayer Materials for Aerospace Transparent Enclosures |
| BS EN 13492:2013 | Geosynthetic barriers. Characteristics required for use in the construction of liquid waste disposal sites, transfer stations or secondary containment |
| BS EN 1770:1998 | Products and systems for the protection and repair of concrete structures. Test methods. Determination of the coefficient of thermal expansion |
| DIN EN 13492:2013-11 | GEOSYNTHETIC BARRIERS - CHARACTERISTICS REQUIRED FOR USE IN THE CONSTRUCTION OF LIQUID WASTE DISPOSAL SITES, TRANSFER STATIONS OR SECONDARY CONTAINMENT |
| DIN EN 15382:2013-11 | GEOSYNTHETIC BARRIERS - CHARACTERISTICS REQUIRED FOR USE IN TRANSPORTATION INFRASTRUCTURE |
| MIL-P-46120 Revision B:1983 | PLASTIC MOLDING AND EXTRUSION MATERIAL POLYSULFONE |
| MIL-P-46179 Revision A:1986 | PLASTIC MOLDING AND EXTRUSION MATERIAL, POLYAMIDE IMIDE |
| I.S. EN ISO 14692-2:2017 | PETROLEUM AND NATURAL GAS INDUSTRIES - GLASS-REINFORCED PLASTICS (GRP) PIPING - PART 2: QUALIFICATION AND MANUFACTURE (ISO 14692-2:2017) |
| CSA S808 : 2014 | SPECIFICATION FOR FIBRE-REINFORCED POLYMER (FRP) MATERIALS FOR EXTERNALLY REINFORCING STRUCTURES |
| SAE J 2253 : 2017 | TEST PROCEDURES FOR AUTOMOTIVE STRUCTURAL COMPOSITE MATERIALS |
| MIL P 5425 : D | PLASTIC, SHEET, ACRYLIC, HEAT RESISTANT |
| ASTM E 289 : 2017 : REDLINE | Standard Test Method for Linear Thermal Expansion of Rigid Solids with Interferometry |
| DIN EN 15382 E : 2013 | GEOSYNTHETIC BARRIERS - CHARACTERISTICS REQUIRED FOR USE IN TRANSPORTATION INFRASTRUCTURE |
| CSA S807 : 2010 : R2015 | SPECIFICATION FOR FIBRE-REINFORCED POLYMERS |
| 12/30267851 DC : 0 | BS EN 13491 - GEOSYNTHETIC BARRIERS - CHARACTERISTICS REQUIRED FOR USE AS A FLUID BARRIER IN THE CONSTRUCTION OF TUNNELS AND ASSOCIATED UNDERGROUND STRUCTURES |
| MIL-I-16923 Revision H:1991 | INSULATING COMPOUND, ELECTRICAL, EMBEDDING, EPOXY |
| MIL-PRF-8184 Revision F:1998 | PLASTIC SHEET, ACRYLIC MODIFIED |
| ASTM F 635 : 1985 : R1991 | Guide for Selection of Tests for Material Properties of Liquid Thermoset Encapsulating Compounds for Electronic and Microelectronic Encapsulation (Withdrawn 1996) |
| ASTM D 7793 : 2017 : REDLINE | Standard Specification for Insulated Vinyl Siding |
| UNI CEN ISO/TS 24817 : 2011 | PETROLEUM, PETROCHEMICAL AND NATURAL GAS INDUSTRIES - COMPOSITE REPAIRS FOR PIPEWORK - QUALIFICATION AND DESIGN, INSTALLATION, TESTING AND INSPECTION |
| UNI 11489 : 2013 | GEOSYNTHETIC BARRIERS - POLYMERIC GEOSYNTHETICS MADE OF PLASTIFIED POLYVINILCLORIDE - CHARACTERISTICS AND ACCEPTANCE LIMITS |
| PREN 4691-1 : DRAFT 2015 | AEROSPACE SERIES - TIE ROD WITH INTEGRATED BOLTS - PART 1: TECHNICAL SPECIFICATION |
| EN 4691-1:2017 | Aerospace series - Tie rod with integrated bolts - Part 1: Technical specification |
| DIN EN 13361:2016-08 (Draft) | GEOSYNTHETIC BARRIERS - CHARACTERISTICS REQUIRED FOR USE IN THE CONSTRUCTION OF RESERVOIRS AND DAMS |
| DIN EN 13491:2016-08 (Draft) | GEOSYNTHETIC BARRIERS - CHARACTERISTICS REQUIRED FOR USE AS A FLUID BARRIER IN THE CONSTRUCTION OF TUNNELS AND ASSOCIATED UNDERGROUND STRUCTURES |
| DIN EN 13492:2016-08 (Draft) | GEOSYNTHETIC BARRIERS - CHARACTERISTICS REQUIRED FOR USE IN THE CONSTRUCTION OF LIQUID WASTE DISPOSAL SITES, TRANSFER STATIONS OR SECONDARY CONTAINMENT |
| ASTM F 790 : 2008 : R2013 | Standard Guide for Testing Materials for Aerospace Plastic Transparent Enclosures |
| ASTM D 7031 : 2011 : REDLINE | GUIDE FOR EVALUATING MECHANICAL AND PHYSICAL PROPERTIES OF WOOD-PLASTIC COMPOSITE PRODUCTS |
| PREN 13362 : DRAFT 2012 | GEOSYNTHETIC BARRIERS - CHARACTERISTICS REQUIRED FOR USE IN THE CONSTRUCTION OF CANALS |
| ASTM D 6455 : 2011 | Standard Guide for the Selection of Test Methods for Prefabricated Bituminous Geomembranes (PBGM) |
| ASTM D 5140 : 1995 | Standard Guide for Testing Polyurethane "Poured in Place" Thermal Break Materials (Withdrawn 2004) |
| I.S. EN 13361:2018 | GEOSYNTHETIC BARRIERS - CHARACTERISTICS REQUIRED FOR USE IN THE CONSTRUCTION OF RESERVOIRS AND DAMS |
| DIN EN 13493:2016-08 (Draft) | GEOSYNTHETIC BARRIERS - CHARACTERISTICS REQUIRED FOR USE IN THE CONSTRUCTION OF SOLID WASTE STORAGE AND DISPOSAL SITES |
| DIN EN 13361:2013-11 | GEOSYNTHETIC BARRIERS - CHARACTERISTICS REQUIRED FOR USE IN THE CONSTRUCTION OF RESERVOIRS AND DAMS |
| ISO/TS 24817:2006 | Petroleum, petrochemical and natural gas industries Composite repairs for pipework Qualification and design, installation, testing and inspection |
| ASME PCC 2 : 2015 | REPAIR OF PRESSURE EQUIPMENT AND PIPING |
| ASME B31.8 : 2016 | Gas Transmission and Distribution Piping Systems |
| L-C-530 Revision C:1987 | COATING, PIPE, THERMOPLASTIC RESIN |
| DD CEN ISO/TS 24817:2011 | Petroleum, petrochemical and natural gas industries. Composite repairs for pipework. Qualification and design, installation, testing and inspection |
| ASTM F 1499 : 2017 : REDLINE | Standard Specification for Coextruded Composite Drain, Waste, and Vent Pipe (DWV) |
| EN 16994:2018 | Clay Geosynthetic Barriers - Characteristics required for use in the construction of underground structures (other than tunnels and associated structures) |
| BS EN 16994:2018 | Clay Geosynthetic Barriers. Characteristics required for use in the construction of underground structures (other than tunnels and associated structures) |
| MIL-DTL-32265 Base Document:2007 | Folded Fiberglass Mat Fabrication and Packaging |
| ASTM F 790 : 2008 | Standard Guide for Testing Materials for Aerospace Plastic Transparent Enclosures |
| ASTM F 1579 : 2002 | Standard Specification for Polyaryletherketone (PAEK) Polymers for Surgical Implant Applications |
| ISO 24817:2017 | Petroleum, petrochemical and natural gas industries — Composite repairs for pipework — Qualification and design, installation, testing and inspection |
| ASTM F 942 : 2002 : R2013 | Standard Guide for Selection of Test Methods for Interlayer Materials for Aerospace Transparent Enclosures |
| UNI 11498 : 2013 | GEOSYNTHETIC BARRIERS - STRUCTURED POLYMERIC GEOSYNTHETICS MADE OF HIGH AND MEDIUM DENSITY POLYETHYLENE - CHARACTERISTICS AND ACCEPTANCE LIMITS |
| I.S. EN 4691-1:2017 | AEROSPACE SERIES - TIE ROD WITH INTEGRATED BOLTS - PART 1: TECHNICAL SPECIFICATION |
| BS EN ISO 24817:2017 | Petroleum, petrochemical and natural gas industries. Composite repairs for pipework. Qualification and design, installation, testing and inspection |
| EN 13493:2018 | Geosynthetic barriers - Characteristics required for use in the construction of solid waste storage and disposal sites |
| I.S. EN 13491:2018 | GEOSYNTHETIC BARRIERS - CHARACTERISTICS REQUIRED FOR USE AS A FLUID BARRIER IN THE CONSTRUCTION OF TUNNELS AND ASSOCIATED UNDERGROUND STRUCTURES |
| DIN EN 13362:2016-08 (Draft) | GEOSYNTHETIC BARRIERS - CHARACTERISTICS REQUIRED FOR USE IN THE CONSTRUCTION OF CANALS |
| ASTM D 3679 : 2017 : REDLINE | Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Siding |
| I.S. EN ISO 24817:2017 | PETROLEUM, PETROCHEMICAL AND NATURAL GAS INDUSTRIES - COMPOSITE REPAIRS FOR PIPEWORK - QUALIFICATION AND DESIGN, INSTALLATION, TESTING AND INSPECTION (ISO 24817:2017, CORRECTED VERSION 2018-01-01) |
| ASTM D 3841 : 2016 : REDLINE | Standard Specification for Glass-Fiber-Reinforced Polyester Plastic Panels |
| ASTM D 4477 : 2016 : REDLINE | Standard Specification for Rigid (Unplasticized) Poly(Vinyl Chloride) (PVC) Soffit |
| ASTM C 1355/C1355M : 1996 : R2011 | Standard Specification for Glass Fiber Reinforced Gypsum Composites |
| UNI 11494 : 2013 | GEOSYNTHETIC BARRIERS - POLYMERIC GEOSYNTHETICS MADE OF POLYOLEFINS (TPO-FPO) - CHARACTERISTICS AND ACCEPTANCE LIMITS |
| ISO 14692-2:2017 | Petroleum and natural gas industries — Glass-reinforced plastics (GRP) piping — Part 2: Qualification and manufacture |
| NASA KSC SPEC E 0029 : 1972 | COMPOUND, POTTING AND MOLDING ELASTOMERIC, SPECIFICATION FOR |
| CSA S806: 2012 | DESIGN AND CONSTRUCTION OF BUILDING STRUCTURES WITH FIBRE-REINFORCED POLYMERS |
| S806-12 (R2017) | Design and construction of building structures with fibre-reinforced polymers |
| SAE AMS 3732 : 2015 | POTTING COMPOUND, EPOXY ONE PART, FILLED, HEAT CURE, LOW CTE |
| 16/30338108 DC : DRAFT JULY 2016 | BS EN 13362 - GEOSYNTHETIC BARRIERS - CHARACTERISTICS REQUIRED FOR USE IN THE CONSTRUCTION OF CANALS |
| 12/30267854 DC : 0 | BS EN 13492 - GEOSYNTHETIC BARRIERS - CHARACTERISTICS REQUIRED FOR USE AS A FLUID BARRIER IN CONSTRUCTION AND TUNNELS AND ASSOCIATED UNDER GROUND STRUCTURES |
| 12/30267845 DC : 0 | BS EN 13361 - GEOSYNTHETIC BARRIERS - CHARACTERISTICS REQUIRED FOR USE IN THE CONSTRUCTION OF RESERVOIRS AND DAMS |
| ASTM C 1355/C1355M : 1996 | Standard Specification for Glass Fiber Reinforced Gypsum Composites |
| 16/30338117 DC : 0 | BS EN 13493 - GEOSYNTHETIC BARRIERS - CHARACTERISTICS REQUIRED FOR USE IN THE CONSTRUCTION OF SOLID WASTE STORAGE AND DISPOSAL SITES |
| IEEE 1133-1988 | IEEE Application Guide for Evaluating Nonceramic Materials for High-Voltage Outdoor Applications |
| MIL-C-24449 Revision A:1981 | CAST POLYMETHYL METHACRYLATE FOR SHEET STOCK, CUSTOM CASTINGS AND FINISHED WINDOWS |
| ASTM F 1876 : 1998 : R2003 : EDT 1 | Standard Specification for Polyetherketoneetherketoneketone (PEKEKK) Resins for Surgical Implant Applications (Withdrawn 2012) |
| ASTM D 4098 : 1982 : R1987 : EDT 1 | Practice for Evaluating High-Density Rigid Cellular Thermosets (Withdrawn 1994) |
| 12/30268279 DC : 0 | BS EN 13493 - GEOSYNTHETIC BARRIERS - CHARACTERISTICS REQUIRED FOR USE IN THE CONSTRUCTION OF SOLID WASTE STORAGE AND DISPOSAL SITES |
| ASTM C 1355/C1355M : 1996 : R2006 | Standard Specification for Glass Fiber Reinforced Gypsum Composites |
| PREN 13493 : DRAFT 2016 | GEOSYNTHETIC BARRIERS - CHARACTERISTICS REQUIRED FOR USE IN THE CONSTRUCTION OF SOLID WASTE STORAGE AND DISPOSAL SITES |
| PREN 13492 : DRAFT 2016 | GEOSYNTHETIC BARRIERS - CHARACTERISTICS REQUIRED FOR USE IN THE CONSTRUCTION OF LIQUID WASTE DISPOSAL SITES, TRANSFER STATIONS OR SECONDARY CONTAINMENT |
| MIL-PRF-24793 Revision A:2001 | Adhesive, UV Curable, One Part, Fiber Optics |
| 14/30256269 DC : 0 | BS EN ISO 24817 - PETROLEUM, PETROCHEMICAL AND NATURAL GAS INDUSTRIES - COMPOSITE REPAIRS FOR PIPEWORK - QUALIFICATION AND DESIGN, INSTALLATION, TESTING AND INSPECTION |
| ADS-13F-HDBK : 1997 | AERONAUTICAL DESIGN STANDARD - HANDBOOK - AIR VEHICLE MATERIALS AND PROCESSES |
| DD ISO/TS 24817 : 2006 | PETROLEUM, PETROCHEMICAL AND NATURAL GAS INDUSTRIES - COMPOSITE REPAIRS FOR PIPEWORK - QUALIFICATION AND DESIGN, INSTALLATION, TESTING AND INSPECTION |
| L-P-504 Revision E:1991 | PLASTIC SHEET AND FILM, CELLULOSE ACETATE |
| ASTM F 2820 : 2012 | Standard Specification for Polyetherketoneketone (PEKK) Polymers for Surgical Implant Applications |
| I.S. EN 16994:2018 | CLAY GEOSYNTHETIC BARRIERS - CHARACTERISTICS REQUIRED FOR USE IN THE CONSTRUCTION OF UNDERGROUND STRUCTURES (OTHER THAN TUNNELS AND ASSOCIATED STRUCTURES) |
| UNE-EN 13361:2013 | Geosynthetic barriers - Characteristics required for use in the construction of reservoirs and dams |
| UNE-EN 13362:2013 | Geosynthetic barriers - Characteristics required for use in the construction of canals |
| EN 13362:2018 | Geosynthetic Barriers - Characteristics required for use in the construction of canals |
| ASTM D 5593 : 1999 : EDT 1 | Standard Classification for Thermoplastic Elastomers-Olefinic (TEO) (Withdrawn 2005) |
| ASTM D 6455 : 2011 : R2018 | Standard Guide for the Selection of Test Methods for Prefabricated Bituminous Geomembranes (PBGMs) |
| ASTM F 1579 : 2002 : EDT 1 | Standard Specification for Polyaryletherketone (PAEK) Polymers for Surgical Implant Applications (Withdrawn 2011) |
| ASTM D 3678 : 2014 : REDLINE | Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Interior-Profile Extrusions |
| EN 15382:2018 | Geosynthetic barriers - Characteristics required for use in transportation infrastructure |
| ASTM F 2021 : 2017 : REDLINE | Standard Guide for Design and Installation of Plastic Siphonic Roof Drainage Systems |
| EN 13492:2018 | Geosynthetic barriers - Characteristics required for use in the construction of liquid waste disposal sites, transfer stations or secondary containment |
| EN ISO 14692-2:2017 | Petroleum and natural gas industries - Glass-reinforced plastics (GRP) piping - Part 2: Qualification and manufacture (ISO 14692-2:2017) |
| EN 13361:2018 | Geosynthetic barriers - Characteristics required for use in the construction of reservoirs and dams |
| ASTM C 1355/C1355M : 1996 : R2001 | Standard Specification for Glass Fiber Reinforced Gypsum Composites |
| I.S. EN 13493:2013 | GEOSYNTHETIC BARRIERS - CHARACTERISTICS REQUIRED FOR USE IN THE CONSTRUCTION OF SOLID WASTE STORAGE AND DISPOSAL SITES |
| I.S. EN 15382:2013 | GEOSYNTHETIC BARRIERS - CHARACTERISTICS REQUIRED FOR USE IN TRANSPORTATION INFRASTRUCTURE |
| I.S. EN 13362:2018 | GEOSYNTHETIC BARRIERS - CHARACTERISTICS REQUIRED FOR USE IN THE CONSTRUCTION OF CANALS |
| 11/30242263 DC : 0 | BS EN 4691-001 - AEROSPACE SERIES - TIE ROD WITH INTEGRATED BOLTS - TECHNICAL SPECIFICATION |
| BS EN 4691-1:2017 | Aerospace series. Tie rod with integrated bolts Technical specification |
| PREN 13361 : DRAFT 2016 | GEOSYNTHETIC BARRIERS - CHARACTERISTICS REQUIRED FOR USE IN THE CONSTRUCTION OF RESERVOIRS AND DAMS |
| ASTM F 636 : 1985 : R1991 | Guide for Selection of Tests for Material Properties of Transfer Molding Compounds for Electronic and Microelectronic Encapsulation (Withdrawn 1996) |
| 16/30338126 DC : 0 | BS EN 13492 - GEOSYNTHETIC BARRIERS - CHARACTERISTICS REQUIRED FOR USE IN THE CONSTRUCTION OF LIQUID WASTE DISPOSAL SITES, TRANSFER STATIONS OR SECONDARY CONTAINMENT |
| 16/30338105 DC : 0 | BS EN 16994 - CLAY GEOSYNTHETIC BARRIERS - CHARACTERISTICS REQUIRED FOR USE AS A FLUID BARRIER IN THE CONSTRUCTION OF UNDERGROUND STRUCTURES (OTHER THAN TUNNELS AND ASSOCIATED STRUCTURES) |
| UNE-EN 13492:2013 | Geosynthetic barriers - Characteristics required for use in the construction of liquid waste disposal sites, transfer stations or secondary containment |
| MIL P 008184 : D | PLASTIC SHEET, ACRYLIC, MODIFIED |
| SAE AMS 3731 : 2016 | POTTING COMPOUND, EPOXY, BISPHENOL A-TYPE |
| I.S. EN 13492:2013 | GEOSYNTHETIC BARRIERS - CHARACTERISTICS REQUIRED FOR USE IN THE CONSTRUCTION OF LIQUID WASTE DISPOSAL SITES, TRANSFER STATIONS OR SECONDARY CONTAINMENT |
| 16/30338111 DC : 0 | BS EN 13491 - GEOSYNTHETIC BARRIERS - CHARACTERISTICS REQUIRED FOR USE AS A FLUID BARRIER IN THE CONSTRUCTION OF TUNNELS AND ASSOCIATED UNDERGROUND STRUCTURES |
| ASTM D 710 : 2013 : REDLINE | Standard Specification for Vulcanized Fibre Sheets, Rods, and Tubes Used for Electrical Insulation |
| 16/30338120 DC : 0 | BS EN 15382 - GEOSYNTHETIC BARRIERS - CHARACTERISTICS REQUIRED FOR USE IN TRANSPORTATION INFRASTRUCTURE |
| UNE-EN 13493:2013 | Geosynthetic barriers - Characteristics required for use in the construction of solid waste storage and disposal sites |
| MIL-R-47025 Revision A:1991 | RESIN, CASTING, FIRE RETARDANT, EPOXY BASE |
| A500-16 | Building guards |
| ACI 440.2R : 2017 | GUIDE FOR THE DESIGN AND CONSTRUCTION OF EXTERNALLY BONDED FRP SYSTEMS FOR STRENGTHENING CONCRETE STRUCTURES |
| ISO/TR 15655:2003 | Fire resistance Tests for thermo-physical and mechanical properties of structural materials at elevated temperatures for fire engineering design |
| DIN EN 15382:2016-08 (Draft) | GEOSYNTHETIC BARRIERS - CHARACTERISTICS REQUIRED FOR USE IN TRANSPORTATION INFRASTRUCTURE |
| UNI 11309 : 2008 | GEOSYNTHETIC BARRIERS - POLYMERIC GEOSYNTHETICS MADE OF HIGH AND MEDIUM DENSITY POLIETHYLEN - CHARACTERISTICS AND ACCEPTANCE LIMITS |
| API TR 17TR8 : 2018 | HIGH-PRESSURE HIGH-TEMPERATURE DESIGN GUIDELINES |
| BS EN 13362:2018 | Geosynthetic Barriers. Characteristics required for use in the construction of canals |
| CSA C22.2 No. 126 : 0 | CABLE TRAY SYSTEMS |
| ASTM C 1355/C1355M : 1996 : R2015 | Standard Specification for Glass Fiber Reinforced Gypsum Composites |
| ASTM D 7445 : 2018 : REDLINE | Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Siding with Foam Plastic Backing (Backed Vinyl Siding) |
| ASTM E 1420 : 1991 | Practice for Specifying Polymeric Materials for Service in Ionizing Radiation Environments (Withdrawn 1996) |
| ASTM D 7745 : 2011 | Standard Practice for Testing Pultruded Composites |
| S.R. CEN ISO TS 24817:2011 | PETROLEUM, PETROCHEMICAL AND NATURAL GAS INDUSTRIES - COMPOSITE REPAIRS FOR PIPEWORK - QUALIFICATION AND DESIGN, INSTALLATION, TESTING AND INSPECTION |
| DIN EN 13362:2013-11 | GEOSYNTHETIC BARRIERS - CHARACTERISTICS REQUIRED FOR USE IN THE CONSTRUCTION OF CANALS |
| DIN EN 13493:2013-11 | GEOSYNTHETIC BARRIERS - CHARACTERISTICS REQUIRED FOR USE IN THE CONSTRUCTION OF SOLID WASTE STORAGE AND DISPOSAL SITES |
| CEN ISO/TS 24817:2011 | Petroleum, petrochemical and natural gas industries - Composite repairs for pipework - Qualification and design, installation, testing and inspection (ISO/TS 24817:2006) |
| ASME PVHO 1 : 2016 | SAFETY STANDARD FOR PRESSURE VESSELS FOR HUMAN OCCUPANCY |
| ASTM E 228 : 2017 : REDLINE | Standard Test Method for Linear Thermal Expansion of Solid Materials With a Push-Rod Dilatometer |
| ASTM D 618 : 2013 : REDLINE | Standard Practice for Conditioning Plastics for Testing |
| ASTM D 4065 : 2012 : REDLINE | Standard Practice for Plastics: Dynamic Mechanical Properties: Determination and Report of Procedures |
£62.61
Excluding VAT
GBP
CAD
CHF
CNY
DKK
EUR
GBP
HKD
IDR
INR
JPY
KRW
MXN
NOK
NZD
SEK
SGD
USD
ZAR
PDF - English
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.