• There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

ASTM D 7156 : 2017

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Standard Test Method for Evaluation of Diesel Engine Oils in the T-11 Exhaust Gas Recirculation Diesel Engine
Available format(s)

Hardcopy , PDF

Superseded date

08-03-2024

Language(s)

English

Published date

01-05-2017

1.1 This test method covers an engine test procedure for evaluating diesel engine oils for performance characteristics in a diesel engine equipped with exhaust gas recirculation, including viscosity increase and soot concentrations (loading).2 This test method is commonly referred to as the Mack T-11.

1.1.1This test method also provides the procedure for running an abbreviated length test, which is commonly referred to as the T-11A. The procedures for the T-11A are identical to the T-11 with the exception of the items specifically listed in Annex A8. Additionally, the procedure modifications listed in Annex A8 refer to the corresponding section of the T-11 procedure.

1.2The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.

1.2.1Exceptions—Where there is no direct SI equivalent such as screw threads, National Pipe Threads/diameters, tubing size, or where there is a sole source supply equipment specification.

1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. See Annex A6 for specific safety hazards.

1.4This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Committee
D 02
DocumentType
Test Method
Pages
35
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy
Supersedes

ASTM D 4485 : 2018 : REV A Standard Specification for Performance of Active API Service Category Engine Oils

ASTM D 4175 : 2014 Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants
ASTM D 5967 : 2015 Standard Test Method for Evaluation of Diesel Engine Oils in T-8 Diesel Engine
ASTM D 4485 : 2003 : REV A Standard Specification for Performance of Engine Oils
ASTM D 2622 : 1992 : EDT 1 Standard Test Method for Sulfur in Petroleum Products by X-Ray Spectrometry
ASTM D 4175 : 2009 : REV A : EDT 1 Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants
ASTM D 7422 : 2012 Standard Test Method for Evaluation of Diesel Engine Oils in T-12 Exhaust Gas Recirculation Diesel Engine
ASTM D 6896 : 2012 Standard Test Method for Determination of Yield Stress and Apparent Viscosity of Used Engine Oils at Low Temperature
ASTM D 4175 : 2008 : REV B : EDT 1 Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants
ASTM D 5453 : 2009 Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Spark Ignition Engine Fuel, Diesel Engine Fuel, and Engine Oil by Ultraviolet Fluorescence
ASTM D 2274 : 2010 Standard Test Method for Oxidation Stability of Distillate Fuel Oil (Accelerated Method)
ASTM D 4485 : 2006 Standard Specification for Performance of Engine Oils
ASTM D 6278 : 1998 Standard Test Method for Shear Stability of Polymer Containing Fluids Using a European Diesel Injector Apparatus
ASTM D 2622 : 1987 : EDT 1 Standard Test Method for Sulfur in Petroleum Products by X-Ray Spectrometry
ASTM D 2709 : 1996 : R2011 : EDT 1 Standard Test Method for Water and Sediment in Middle Distillate Fuels by Centrifuge
ASTM D 4175 : 2005 Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants
ASTM D 3524 : 2004 Standard Test Method for Diesel Fuel Diluent in Used Diesel Engine Oils by Gas Chromatography (Withdrawn 2013)
ASTM D 2709 : 1996 : EDT 2 Standard Test Method for Water and Sediment in Middle Distillate Fuels by Centrifuge
ASTM D 4485 : 2011 : REV C Standard Specification for Performance of Active API Service Category Engine Oils
ASTM D 1319 : 1989 Standard Test Method for Hydrocarbon Types in Liquid Petroleum Products by Fluorescent Indicator Absorption
ASTM D 4175 : 2005 : EDT 2 Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants
ASTM D 1319 : 2008 Standard Test Method for Hydrocarbon Types in Liquid Petroleum Products by Fluorescent Indicator Adsorption
ASTM D 5967 : 2014 Standard Test Method for Evaluation of Diesel Engine Oils in T-8 Diesel Engine
ASTM D 4485 : 2001 Standard Specification for Performance of Engine Oils
ASTM D 5967 : 2008 Standard Test Method for Evaluation of Diesel Engine Oils in T-8 Diesel Engine
ASTM D 5453 : 2008 : REV B Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Spark Ignition Engine Fuel, Diesel Engine Fuel, and Engine Oil by Ultraviolet Fluorescence
ASTM D 5453 : 2000 Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Motor Fuels and Oils by Ultraviolet Fluorescence
ASTM D 7422 : 2009 Standard Test Method for Evaluation of Diesel Engine Oils in T-12 Exhaust Gas Recirculation Diesel Engine
ASTM D 5185 : 1997 Standard Test Method for Determination of Additive Elements, Wear Metals, and Contaminants in Used Lubricating Oils and Determination of Selected Elements in Base Oils by Inductively Coupled Plasma Atomic Emission Spectrometry (ICP-AES)
ASTM D 4175 : 2015 : REV C Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants
ASTM D 5967 : 2009 Standard Test Method for Evaluation of Diesel Engine Oils in T-8 Diesel Engine
ASTM D 4175 : 2017 : REV A : EDT 1 Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants
ASTM D 2274 : 2001 Standard Test Method for Oxidation Stability of Distillate Fuel Oil (Accelerated Method)
ASTM D 4485 : 2003 Standard Specification for Performance of Engine Oils
ASTM D 4052 : 1996 : R2002 : EDT 1 Standard Test Method for Density and Relative Density of Liquids by Digital Density Meter
ASTM D 4485 : 2008 Standard Specification for Performance of Engine Oils
ASTM D 4739 : 2005 Standard Test Method for Base Number Determination by Potentiometric Titration
ASTM D 2709 : 1996 : R2006 Standard Test Method for Water and Sediment in Middle Distillate Fuels by Centrifuge
ASTM D 4485 : 2015 Standard Specification for Performance of Active API Service Category Engine Oils
ASTM D 5453 : 2004 Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Motor Fuels and Oils by Ultraviolet Fluorescence
ASTM D 1319 : 2018 Standard Test Method for Hydrocarbon Types in Liquid Petroleum Products by Fluorescent Indicator Adsorption
ASTM D 4485 : 2005 : REV A Standard Specification for Performance of Engine Oils
ASTM D 6896 : 2018 Standard Test Method for Determination of Yield Stress and Apparent Viscosity of Used Engine Oils at Low Temperature
ASTM D 7422 : 2016 : REV A Standard Test Method for Evaluation of Diesel Engine Oils in T-12 Exhaust Gas Recirculation Diesel Engine
ASTM D 6896 : 2003 Standard Test Method for Determination of Yield Stress and Apparent Viscosity of Used Engine Oils at Low Temperature
ASTM D 4175 : 2008 : REV A Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants
ASTM D 5453 : 2012 Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Spark Ignition Engine Fuel, Diesel Engine Fuel, and Engine Oil by Ultraviolet Fluorescence
ASTM D 4294 : 2010 Standard Test Method for Sulfur in Petroleum and Petroleum Products by Energy Dispersive X-ray Fluorescence Spectrometry
ASTM D 2500 : 2016 : REV B Standard Test Method for Cloud Point of Petroleum Products and Liquid Fuels
ASTM D 4052 : 2018 : REV A Standard Test Method for Density, Relative Density, and API Gravity of Liquids by Digital Density Meter
ASTM D 5967 : 2012 Standard Test Method for Evaluation of Diesel Engine Oils in T-8 Diesel Engine
ASTM D 1319 : 2014 Standard Test Method for Hydrocarbon Types in Liquid Petroleum Products by Fluorescent Indicator Adsorption
ASTM D 4175 : 2017 : REV B Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants
ASTM D 4175 : 2009 Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants
ASTM D 4485 : 2011 : REV A Standard Specification for Performance of Active API Service Category Engine Oils
ASTM D 5967 : 2003 Standard Test Method for Evaluation of Diesel Engine Oils in T-8 Diesel Engine
ASTM D 2622 : 1998 Standard Test Method for Sulfur in Petroleum Products by Wavelength Dispersive X-ray Fluorescence Spectrometry
ASTM D 2500 : 2016 : REV A Standard Test Method for Cloud Point of Petroleum Products and Liquid Fuels
ASTM D 2274 : 2003 : REV A : R2008 Standard Test Method for Oxidation Stability of Distillate Fuel Oil (Accelerated Method)
ASTM D 2500 : 2016 Standard Test Method for Cloud Point of Petroleum Products
ASTM D 1319 : 1999 Standard Test Method for Hydrocarbon Types in Liquid Petroleum Products by Fluorescent Indicator Adsorption
ASTM D 7422 : 2015 Standard Test Method for Evaluation of Diesel Engine Oils in T-12 Exhaust Gas Recirculation Diesel Engine
ASTM D 4485 : 2018 Standard Specification for Performance of Active API Service Category Engine Oils
ASTM D 5185 : 2005 Standard Test Method for Determination of Additive Elements, Wear Metals, and Contaminants in Used Lubricating Oils and Determination of Selected Elements in Base Oils by Inductively Coupled Plasma Atomic Emission Spectrometry (ICP-AES)
ASTM D 4737 : 2009 Standard Test Method for Calculated Cetane Index by Four Variable Equation
ASTM D 4175 : 2009 : REV A : EDT 4 Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants
ASTM D 4175 : 2009 : REV A : EDT 3 Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants
ASTM D 4052 : 2009 Standard Test Method for Density, Relative Density, and API Gravity of Liquids by Digital Density Meter
ASTM D 5453 : 2008 : REV A Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Spark Ignition Engine Fuel, Diesel Engine Fuel, and Engine Oil by Ultraviolet Fluorescence
ASTM D 5967 : 2004 Standard Test Method for Evaluation of Diesel Engine Oils in T-8 Diesel Engine
ASTM D 5185 : 2002 Standard Test Method for Determination of Additive Elements, Wear Metals, and Contaminants in Used Lubricating Oils and Determination of Selected Elements in Base Oils by Inductively Coupled Plasma Atomic Emission Spectrometry (ICP-AES)
ASTM D 7109 : 2007 Standard Test Method for Shear Stability of Polymer Containing Fluids Using a European Diesel Injector Apparatus at 30 and 90 Cycles
ASTM D 4485 : 2011 : REV B Standard Specification for Performance of Active API Service Category Engine Oils
ASTM D 2622 : 2008 Standard Test Method for Sulfur in Petroleum Products by Wavelength Dispersive X-ray Fluorescence Spectrometry
ASTM D 4485 : 2016 Standard Specification for Performance of Active API Service Category Engine Oils
ASTM D 4175 : 2018 Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants
ASTM D 4485 : 2007 Standard Specification for Performance of Engine Oils
ASTM D 7422 : 2014 : REV A Standard Test Method for Evaluation of Diesel Engine Oils in T-12 Exhaust Gas Recirculation Diesel Engine
ASTM D 4485 : 2010 Standard Specification for Performance of Engine Oils
ASTM D 5185 : 2018 Standard Test Method for Multielement Determination of Used and Unused Lubricating Oils and Base Oils by Inductively Coupled Plasma Atomic Emission Spectrometry (ICP-AES)
ASTM D 4485 : 2001 : REV A Standard Specification for Performance of Engine Oils
ASTM D 7422 : 2010 : REV A Standard Test Method for Evaluation of Diesel Engine Oils in T-12 Exhaust Gas Recirculation Diesel Engine
ASTM D 7422 : 2008 Standard Test Method for Evaluation of Diesel Engine Oils in T-12 Exhaust Gas Recirculation Diesel Engine
ASTM D 4175 : 2001 : EDT 1 Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants
ASTM D 1319 : 2002 : REV A Standard Test Method for Hydrocarbon Types in Liquid Petroleum Products by Fluorescent Indicator Adsorption
ASTM D 2274 : 2003 Standard Test Method for Oxidation Stability of Distillate Fuel Oil (Accelerated Method)
ASTM D 5453 : 2005 Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Motor Fuels and Oils by Ultraviolet Fluorescence
ASTM D 7422 : 2017 : REV A Standard Test Method for Evaluation of Diesel Engine Oils in T-12 Exhaust Gas Recirculation Diesel Engine
ASTM D 7109 : 2012 Standard Test Method for Shear Stability of Polymer Containing Fluids Using a European Diesel Injector Apparatus at 30 and 90 Cycles
ASTM D 2709 : 2016 Standard Test Method for Water and Sediment in Middle Distillate Fuels by Centrifuge
ASTM D 4175 : 2001 Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants
ASTM D 4175 : 2005 : EDT 1 Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants
ASTM D 2500 : 1999 Standard Test Method for Cloud Point of Petroleum Products
ASTM D 2500 : 2002 : EDT 1 Standard Test Method for Cloud Point of Petroleum Products
ASTM D 7109 : 2005 Standard Test Method for Shear Stability of Polymer Containing Fluids Using a European Diesel Injector Apparatus at 30 and 90 Cycles
ASTM D 4739 : 2008 Standard Test Method for Base Number Determination by Potentiometric Hydrochloric Acid Titration
ASTM D 2500 : 2005 Standard Test Method for Cloud Point of Petroleum Products
ASTM D 4175 : 2002 Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants
ASTM D 5185 : 2013 : EDT 1 Standard Test Method for Multielement Determination of Used and Unused Lubricating Oils and Base Oils by Inductively Coupled Plasma Atomic Emission Spectrometry (ICP-AES)
ASTM D 4485 : 2004 Standard Specification for Performance of Engine Oils
ASTM D 5453 : 2006 Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Spark Ignition Engine Fuel, Diesel Engine Fuel, and Engine Oil by Ultraviolet Fluorescence
ASTM D 6896 : 2003 : R2007 Standard Test Method for Determination of Yield Stress and Apparent Viscosity of Used Engine Oils at Low Temperature
ASTM D 2500 : 2002 Standard Test Method for Cloud Point of Petroleum Products
ASTM D 2500 : 2011 Standard Test Method for Cloud Point of Petroleum Products
ASTM D 4739 : 2017 Standard Test Method for Base Number Determination by Potentiometric Hydrochloric Acid Titration
ASTM D 5967 : 2015 : REV A Standard Test Method for Evaluation of Diesel Engine Oils in T-8 Diesel Engine
ASTM D 2500 : 2009 Standard Test Method for Cloud Point of Petroleum Products
ASTM D 3524 : 2014 Standard Test Method for Diesel Fuel Diluent in Used Diesel Engine Oils by Gas Chromatography
ASTM D 4739 : 2006 Standard Test Method for Base Number Determination by Potentiometric Titration
ASTM D 4294 : 2008 Standard Test Method for Sulfur in Petroleum and Petroleum Products by Energy Dispersive X-ray Fluorescence Spectrometry
ASTM D 4175 : 2015 Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants
ASTM D 4485 : 2000 Standard Specification for Performance of Engine Oils
ASTM D 6896 : 2014 Standard Test Method for Determination of Yield Stress and Apparent Viscosity of Used Engine Oils at Low Temperature
ASTM D 4175 : 2002 : REV A : EDT 2 Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants
ASTM D 4739 : 1996 Standard Test Method for Base Number Determination by Potentiometric Titration
ASTM D 2500 : 2017 Standard Test Method for Cloud Point of Petroleum Products and Liquid Fuels
ASTM D 4052 : 2011 Standard Test Method for Density, Relative Density, and API Gravity of Liquids by Digital Density Meter
ASTM D 1319 : 2003 Standard Test Method for Hydrocarbon Types in Liquid Petroleum Products by Fluorescent Indicator Adsorption
ASTM D 4052 : 2016 Standard Test Method for Density, Relative Density, and API Gravity of Liquids by Digital Density Meter
ASTM D 7422 : 2013 Standard Test Method for Evaluation of Diesel Engine Oils in T-12 Exhaust Gas Recirculation Diesel Engine
ASTM D 4485 : 2015 : REV A Standard Specification for Performance of Active API Service Category Engine Oils
ASTM D 5185 : 2013 Standard Test Method for Multielement Determination of Used and Unused Lubricating Oils and Base Oils by Inductively Coupled Plasma Atomic Emission Spectrometry (ICP-AES)
ASTM D 2622 : 2003 Standard Test Method for Sulfur in Petroleum Products by Wavelength Dispersive X-ray Fluorescence Spectrometry
ASTM D 5453 : 2016 Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Spark Ignition Engine Fuel, Diesel Engine Fuel, and Engine Oil by Ultraviolet Fluorescence
ASTM D 4294 : 2008 : REV A Standard Test Method for Sulfur in Petroleum and Petroleum Products by Energy Dispersive X-ray Fluorescence Spectrometry
ASTM D 1319 : 2010 Standard Test Method for Hydrocarbon Types in Liquid Petroleum Products by Fluorescent Indicator Adsorption
ASTM D 4175 : 2009 : REV A : EDT 5 Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants
ASTM D 4175 : 2016 : REV C Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants
ASTM D 4737 : 2009 : REV A Standard Test Method for Calculated Cetane Index by Four Variable Equation
ASTM D 5967 : 2011 Standard Test Method for Evaluation of Diesel Engine Oils in T-8 Diesel Engine
ASTM D 4175 : 2015 : REV B Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants
ASTM D 7422 : 2015 : REV A Standard Test Method for Evaluation of Diesel Engine Oils in T-12 Exhaust Gas Recirculation Diesel Engine
ASTM D 6278 : 2017 Standard Test Method for Shear Stability of Polymer Containing Fluids Using a European Diesel Injector Apparatus
ASTM D 4294 : 2002 Standard Test Method for Sulfur in Petroleum Products by Energy-Dispersive X-Ray Fluorescence Spectroscopy
ASTM D 4175 : 2015 : REV A Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants
ASTM D 5967 : 2017 Standard Test Method for Evaluation of Diesel Engine Oils in T-8 Diesel Engine
ASTM D 4485 : 2006 : REV A Standard Specification for Performance of Engine Oils
ASTM D 4739 : 2011 : R2017 Standard Test Method for Base Number Determination by Potentiometric Hydrochloric Acid Titration
ASTM D 4737 : 2010 : R2016 Standard Test Method for Calculated Cetane Index by Four Variable Equation
ASTM D 5453 : 2003 Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Motor Fuels and Oils by Ultraviolet Fluorescence
ASTM D 2274 : 1994 : R1999 : EDT 1 Standard Test Method for Oxidation Stability of Distillate Fuel Oil (Accelerated Method)
ASTM D 4175 : 2009 : REV A Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants
ASTM D 7109 : 2004 Standard Test Method for Shear Stability of Polymer Containing Fluids Using a European Diesel Injector Apparatus at 30 and 90 Cycles
ASTM D 4175 : 2016 : REV B Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants
ASTM D 7422 : 2016 Standard Test Method for Evaluation of Diesel Engine Oils in T-12 Exhaust Gas Recirculation Diesel Engine
ASTM D 2500 : 2017 : REV A Standard Test Method for Cloud Point of Petroleum Products and Liquid Fuels
ASTM D 7422 : 2011 Standard Test Method for Evaluation of Diesel Engine Oils in T-12 Exhaust Gas Recirculation Diesel Engine
ASTM D 4175 : 2002 : REV A : EDT 1 Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants
ASTM D 4175 : 2008 Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants
ASTM D 7422 : 2010 Standard Test Method for Evaluation of Diesel Engine Oils in T-12 Exhaust Gas Recirculation Diesel Engine
ASTM D 6278 : 2017 : EDT 1 Standard Test Method for Shear Stability of Polymer Containing Fluids Using a European Diesel Injector Apparatus
ASTM D 4737 : 2003 Standard Test Method for Calculated Cetane Index by Four Variable Equation
ASTM D 4175 : 2002 : REV A Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants
ASTM D 4294 : 2016 : EDT 1 Standard Test Method for Sulfur in Petroleum and Petroleum Products by Energy Dispersive X-ray Fluorescence Spectrometry
ASTM D 5453 : 2016 : EDT 1 Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Spark Ignition Engine Fuel, Diesel Engine Fuel, and Engine Oil by Ultraviolet Fluorescence
ASTM D 6278 : 2012 : EDT 1 Standard Test Method for Shear Stability of Polymer Containing Fluids Using a European Diesel Injector Apparatus
ASTM D 4175 : 2000 : EDT 1 Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants
ASTM D 3524 : 1990 : R1999 Standard Test Method for Diesel Fuel Diluent in Used Diesel Engine Oils by Gas Chromatography
ASTM D 4175 : 2016 : REV A Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants
ASTM D 5967 : 2007 Standard Test Method for Evaluation of Diesel Engine Oils in T-8 Diesel Engine
ASTM D 7109 : 2018 Standard Test Method for Shear Stability of Polymer-Containing Fluids Using a European Diesel Injector Apparatus at 30 Cycles and 90 Cycles
ASTM D 5967 : 2010 Standard Test Method for Evaluation of Diesel Engine Oils in T-8 Diesel Engine
ASTM D 4294 : 2008 : REV A : EDT 1 Standard Test Method for Sulfur in Petroleum and Petroleum Products by Energy Dispersive X-ray Fluorescence Spectrometry
ASTM D 4052 : 1996 Standard Test Method for Density and Relative Density of Liquids by Digital Density Meter
ASTM D 4294 : 1998 Standard Test Method for Sulfur in Petroleum Products by Energy-Dispersive X-Ray Fluorescence Spectroscopy
ASTM D 4739 : 2008 : EDT 1 Standard Test Method for Base Number Determination by Potentiometric Hydrochloric Acid Titration
ASTM D 2622 : 2010 Standard Test Method for Sulfur in Petroleum Products by Wavelength Dispersive X-ray Fluorescence Spectrometry
ASTM D 2709 : 1988 Standard Test Method for Water and Sediment in Distillate Fuels by Centrifuge
ASTM D 4485 : 2005 Standard Specification for Performance of Engine Oils
ASTM D 5185 : 2009 Standard Test Method for Determination of Additive Elements, Wear Metals, and Contaminants in Used Lubricating Oils and Determination of Selected Elements in Base Oils by Inductively Coupled Plasma Atomic Emission Spectrometry (ICP-AES)
ASTM D 4737 : 1996 : REV A Standard Test Method for Calculated Cetane Index by Four Variable Equation
ASTM D 7422 : 2009 : REV A Standard Test Method for Evaluation of Diesel Engine Oils in T-12 Exhaust Gas Recirculation Diesel Engine
ASTM D 4485 : 2014 Standard Specification for Performance of Active API Service Category Engine Oils
ASTM D 5453 : 2019 : REV A Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Spark Ignition Engine Fuel, Diesel Engine Fuel, and Engine Oil by Ultraviolet Fluorescence
ASTM D 5967 : 2013 Standard Test Method for Evaluation of Diesel Engine Oils in T-8 Diesel Engine
ASTM D 4485 : 2002 Standard Specification for Performance of Engine Oils
ASTM D 5967 : 2012 : REV A Standard Test Method for Evaluation of Diesel Engine Oils in T-8 Diesel Engine
ASTM D 2622 : 2007 Standard Test Method for Sulfur in Petroleum Products by Wavelength Dispersive X-ray Fluorescence Spectrometry
ASTM D 6896 : 2003 : EDT 1 Standard Test Method for Determination of Yield Stress and Apparent Viscosity of Used Engine Oils at Low Temperature
ASTM D 4175 : 2017 : REV A Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants
ASTM D 2274 : 2003 : REV A Standard Test Method for Oxidation Stability of Distillate Fuel Oil (Accelerated Method)
ASTM D 4485 : 2005 : EDT 1 Standard Specification for Performance of Engine Oils
ASTM D 2622 : 1994 Standard Test Method for Sulfur in Petroleum Products by X-Ray Spectrometry
ASTM D 5967 : 2005 Standard Test Method for Evaluation of Diesel Engine Oils in T-8 Diesel Engine
ASTM D 4175 : 2009 : REV A : EDT 2 Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants
ASTM D 2622 : 2005 Standard Test Method for Sulfur in Petroleum Products by Wavelength Dispersive X-ray Fluorescence Spectrometry
ASTM D 5185 : 2002 : EDT 1 Standard Test Method for Determination of Additive Elements, Wear Metals, and Contaminants in Used Lubricating Oils and Determination of Selected Elements in Base Oils by Inductively Coupled Plasma Atomic Emission Spectrometry (ICP-AES)
ASTM D 4294 : 2003 Standard Test Method for Sulfur in Petroleum and Petroleum Products by Energy-Dispersive X-Ray Fluorescence Spectrometry
ASTM D 4737 : 2004 Standard Test Method for Calculated Cetane Index by Four Variable Equation
ASTM D 5453 : 2019 Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Spark Ignition Engine Fuel, Diesel Engine Fuel, and Engine Oil by Ultraviolet Fluorescence
ASTM D 4175 : 2018 : EDT 1 Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants
ASTM D 4175 : 2016 Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants
ASTM D 5967 : 2010 : REV A Standard Test Method for Evaluation of Diesel Engine Oils in T-8 Diesel Engine
ASTM D 1319 : 2015 Standard Test Method for Hydrocarbon Types in Liquid Petroleum Products by Fluorescent Indicator Adsorption
ASTM D 7422 : 2017 Standard Test Method for Evaluation of Diesel Engine Oils in T-12 Exhaust Gas Recirculation Diesel Engine
ASTM D 4294 : 2016 Standard Test Method for Sulfur in Petroleum and Petroleum Products by Energy Dispersive X-ray Fluorescence Spectrometry
ASTM D 5185 : 2002 : EDT 2 Standard Test Method for Determination of Additive Elements, Wear Metals, and Contaminants in Used Lubricating Oils and Determination of Selected Elements in Base Oils by Inductively Coupled Plasma Atomic Emission Spectrometry (ICP-AES)
ASTM D 4739 : 2011 Standard Test Method for Base Number Determination by Potentiometric Hydrochloric Acid Titration
ASTM D 4739 : 2002 Standard Test Method for Base Number Determination by Potentiometric Titration
ASTM D 1319 : 2013 Standard Test Method for Hydrocarbon Types in Liquid Petroleum Products by Fluorescent Indicator Adsorption
ASTM D 4052 : 2015 Standard Test Method for Density, Relative Density, and API Gravity of Liquids by Digital Density Meter
ASTM D 4739 : 2006 : REV A Standard Test Method for Base Number Determination by Potentiometric Titration
ASTM D 6278 : 2002 Standard Test Method for Shear Stability of Polymer Containing Fluids Using a European Diesel Injector Apparatus
ASTM D 5967 : 1999 : REV A Standard Test Method for Evaluation of Diesel Engine Oils in T-8 Diesel Engine
ASTM D 4175 : 2017 Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants
ASTM D 6278 : 2007 Standard Test Method for Shear Stability of Polymer Containing Fluids Using a European Diesel Injector Apparatus
ASTM D 4175 : 2019 Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants
ASTM D 2274 : 2001 : REV A Standard Test Method for Oxidation Stability of Distillate Fuel Oil (Accelerated Method)
ASTM D 4485 : 2009 Standard Specification for Performance of Engine Oils
ASTM D 2274 : 2014 Standard Test Method for Oxidation Stability of Distillate Fuel Oil (Accelerated Method)
ASTM D 4175 : 2015 : REV B : EDT 1 Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants
ASTM D 6896 : 2017 Standard Test Method for Determination of Yield Stress and Apparent Viscosity of Used Engine Oils at Low Temperature
ASTM D 4485 : 2010 : REV A Standard Specification for Performance of Engine Oils
ASTM D 5453 : 2003 : REV A Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Motor Fuels and Oils by Ultraviolet Fluorescence
ASTM D 4485 : 2011 Standard Specification for Performance of Engine Oils
ASTM D 1319 : 2019 Standard Test Method for Hydrocarbon Types in Liquid Petroleum Products by Fluorescent Indicator Adsorption
ASTM D 7109 : 2006 Standard Test Method for Shear Stability of Polymer Containing Fluids Using a European Diesel Injector Apparatus at 30 and 90 Cycles
ASTM D 4052 : 2018 Standard Test Method for Density, Relative Density, and API Gravity of Liquids by Digital Density Meter
ASTM D 4737 : 2010 Standard Test Method for Calculated Cetane Index by Four Variable Equation
ASTM D 4294 : 1990 : R1998 : EDT 1 Standard Test Method for Sulfur in Petroleum Products by Energy-Dispersive X-Ray Fluorescence Spectroscopy
ASTM D 1319 : 2002 Standard Test Method for Hydrocarbon Types in Liquid Petroleum Products by Fluorescent Indicator Adsorption
ASTM D 4175 : 2008 : REV B Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants
ASTM D 2622 : 2016 Standard Test Method for Sulfur in Petroleum Products by Wavelength Dispersive X-ray Fluorescence Spectrometry
ASTM D 2709 : 1996 : R2001 : EDT 1 Standard Test Method for Water and Sediment in Middle Distillate Fuels by Centrifuge
ASTM D 7422 : 2014 Standard Test Method for Evaluation of Diesel Engine Oils in T-12 Exhaust Gas Recirculation Diesel Engine
ASTM D 5453 : 2008 Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Spark Ignition Engine Fuel, Diesel Engine Fuel, and Engine Oil by Ultraviolet Fluorescence
ASTM D 4485 : 2007 : REV A Standard Specification for Performance of Engine Oils
ASTM D 5453 : 2000 : EDT 1 Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Motor Fuels and Oils by Ultraviolet Fluorescence

View more information
£90.16
Excluding VAT

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.