• There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

ASTM D 7165 : 2010 : R2015

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Standard Practice for Gas Chromatograph Based On-line/At-line Analysis for Sulfur Content of Gaseous Fuels
Available format(s)

Hardcopy , PDF

Superseded date

12-11-2022

Language(s)

English

Published date

03-07-2015

CONTAINED IN VOL. 05.06, 2015 Defines the determination of volatile sulfur-containing compounds in high methane content gaseous fuels such as natural gas using on-line/at-line instrumentation, and continuous fuel monitors (CFMS).

1.1 This practice is for the determination of volatile sulfur-containing compounds in high methane content gaseous fuels such as natural gas using on-line/at-line instrumentation, and continuous fuel monitors (CFMS). It has been successfully applied to other types of gaseous samples including air, digester, landfill, and refinery fuel gas. The detection range for sulfur compounds, reported as picograms sulfur, based upon the analysis of a 1 cc sample, is one hundred (100) to one million (1,000,000). This is equivalent to 0.1 to 1,000 mg/m3.

1.2This practice does not purport to measure all sulfur species in a sample. Only volatile compounds that are transported to an instrument under the measurement conditions selected are measured.

1.3The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.

1.4This practice does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this practice to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Committee
D 03
DocumentType
Standard Practice
Pages
6
ProductNote
Reconfirmed 2015
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy
Supersedes

ASTM D 8080 : 2021 Standard Specification for Compressed Natural Gas (CNG) and Liquefied Natural Gas (LNG) Used as a Motor Vehicle Fuel
ASTM D 7800/D7800M : 2014 Standard Test Method for Determination of Elemental Sulfur in Natural Gas (Withdrawn 2023)
ASTM D 7493 : 2014 : R2018 Standard Test Method for Online Measurement of Sulfur Compounds in Natural Gas and Gaseous Fuels by Gas Chromatograph and Electrochemical Detection

ASTM D 6122 : 2021 Standard Practice for Validation of the Performance of Multivariate Online, At-Line, Field and Laboratory Infrared Spectrophotometer, and Raman Spectrometer Based Analyzer Systems
ASTM D 6621 : 2000 : R2017 Standard Practice for Performance Testing of Process Analyzers for Aromatic Hydrocarbon Materials
ASTM D 3606 : 2007 Standard Test Method for Determination of Benzene and Toluene in Finished Motor and Aviation Gasoline by Gas Chromatography
ASTM D 6621 : 2000 : R2006 : EDT 1 Standard Practice for Performance Testing of Process Analyzers for Aromatic Hydrocarbon Materials
ASTM D 3606 : 2010 Standard Test Method for Determination of Benzene and Toluene in Finished Motor and Aviation Gasoline by Gas Chromatography
ASTM D 6122 : 2010 Standard Practice for Validation of the Performance of Multivariate Online, At-Line, and Laboratory Infrared Spectrophotometer Based Analyzer Systems
ASTM D 1072 : 2006 : R2012 Standard Test Method for Total Sulfur in Fuel Gases by Combustion and Barium Chloride Titration
ASTM D 6228 : 2010 Standard Test Method for Determination of Sulfur Compounds in Natural Gas and Gaseous Fuels by Gas Chromatography and Flame Photometric Detection (Withdrawn 2019)
ASTM D 6122 : 2020 : REV A Standard Practice for Validation of the Performance of Multivariate Online, At-Line, Field and Laboratory Infrared Spectrophotometer, and Raman Spectrometer Based Analyzer Systems
ASTM D 3764 : 2013 Standard Practice for Validation of the Performance of Process Stream Analyzer Systems
ASTM D 3606 : 2004 Standard Test Method for Determination of Benzene and Toluene in Finished Motor and Aviation Gasoline by Gas Chromatography
ASTM D 6122 : 2013 Standard Practice for Validation of the Performance of Multivariate Online, At-Line, and Laboratory Infrared Spectrophotometer Based Analyzer Systems
ASTM D 6122 : 2006 Standard Practice for Validation of the Performance of Multivariate Process Infrared Spectrophotometers
ASTM D 3764 : 2015 : EDT 1 Standard Practice for Validation of the Performance of Process Stream Analyzer Systems
ASTM D 3764 : 2001 Standard Practice for Validation of Process Stream Analyzer Systems
ASTM D 5504 : 2012 : REDLINE Standard Test Method for Determination of Sulfur Compounds in Natural Gas and Gaseous Fuels by Gas Chromatography and Chemiluminescence
ASTM D 4468 : 1985 : R2015 Standard Test Method for Total Sulfur in Gaseous Fuels by Hydrogenolysis and<brk/> Rateometric Colorimetry
ASTM D 4468 : 1985 : R2000 Standard Test Method for Total Sulfur in Gaseous Fuels by Hydrogenolysis and Rateometric Colorimetry
ASTM D 1945 : 1996 : EDT 1 Standard Test Method for Analysis of Natural Gas by Gas Chromatography
ASTM D 3606 : 2006 Standard Test Method for Determination of Benzene and Toluene in Finished Motor and Aviation Gasoline by Gas Chromatography
ASTM D 3764 : 2006 Standard Practice for Validation of the Performance of Process Stream Analyzer Systems
ASTM D 6122 : 2015 Standard Practice for Validation of the Performance of Multivariate Online, At-Line, and Laboratory Infrared Spectrophotometer Based Analyzer Systems
ASTM D 6228 : 1998 Standard Test Method for Determination of Sulfur Compounds in Natural Gas and Gaseous Fuels by Gas Chromatography and Flame Photometric Detection
ASTM D 3764 : 1992 : R1998 Standard Practice for Validation of Process Stream Analyzer Systems
ASTM D 1945 : 1996 : R2001 Standard Test Method for Analysis of Natural Gas by Gas Chromatography
ASTM D 4084 : 1982 : R1988 Standard Test Method for Analysis of Hydrogen Sulfide in Gaseous Fuels (Lead Acetate Reaction Rate Method)
ASTM D 6228 : 2019 Standard Test Method for Determination of Sulfur Compounds in Natural Gas and Gaseous Fuels by Gas Chromatography and Flame Photometric Detection
ASTM D 6122 : 2019 : REV B Standard Practice for Validation of the Performance of Multivariate Online, At-Line, and Laboratory Infrared Spectrophotometer Based Analyzer Systems
ASTM D 1072 : 1990 : R1999 Standard Test Method for Total Sulfur in Fuel Gases
ASTM D 4084 : 2006 Standard Test Method for Analysis of Hydrogen Sulfide in Gaseous Fuels (Lead Acetate Reaction Rate Method)
ASTM D 6122 : 2001 Standard Practice for Validation of Multivariate Process Infrared Spectrophotometers
ASTM D 4084 : 2005 Standard Test Method for Analysis of Hydrogen Sulfide in Gaseous Fuels (Lead Acetate Reaction Rate Method)
ASTM D 6122 : 2019 : REV A Standard Practice for Validation of the Performance of Multivariate Online, At-Line, and Laboratory Infrared Spectrophotometer Based Analyzer Systems
ASTM D 6122 : 2018 Standard Practice for Validation of the Performance of Multivariate Online, At-Line, and Laboratory Infrared Spectrophotometer Based Analyzer Systems
ASTM D 4626 : 1995 : R2005 Standard Practice for Calculation of Gas Chromatographic Response Factors
ASTM D 3764 : 2019 Standard Practice for Validation of the Performance of Process Stream Analyzer Systems
ASTM D 3606 : 2022 Standard Test Method for Determination of Benzene and Toluene in Spark Ignition Fuels by Gas Chromatography
ASTM D 6621 : 2000 : R2012 Standard Practice for Performance Testing of Process Analyzers for Aromatic Hydrocarbon Materials
ASTM D 4084 : 1994 : R1999 Standard Test Method for Analysis of Hydrogen Sulfide in Gaseous Fuels (Lead Acetate Reaction Rate Method)
ASTM D 3606 : 2017 Standard Test Method for Determination of Benzene and Toluene in Spark Ignition Fuels by Gas Chromatography
ASTM D 6621 : 2021 Standard Practice for Performance Testing of Process Analyzers for Aromatic Hydrocarbon Materials
ASTM D 3606 : 2006 : EDT 1 Standard Test Method for Determination of Benzene and Toluene in Finished Motor and Aviation Gasoline by Gas Chromatography
ASTM D 3764 : 2022 Standard Practice for Validation of the Performance of Process Stream Analyzer Systems
ASTM D 5504 : 2008 Standard Test Method for Determination of Sulfur Compounds in Natural Gas and Gaseous Fuels by Gas Chromatography and Chemiluminescence
ASTM D 4084 : 2007 : R2017 Standard Test Method for Analysis of Hydrogen Sulfide in Gaseous Fuels (Lead Acetate Reaction Rate Method)
ASTM D 1072 : 2006 : R2017 Standard Test Method for Total Sulfur in Fuel Gases by Combustion and Barium Chloride Titration
ASTM D 6122 : 2016-02 PRACTICE FOR VALIDATION OF THE PERFORMANCE OF MULTIVARIATE ONLINE, AT-LINE, AND LABORATORY INFRARED SPECTROPHOTOMETER BASED ANALYZER SYSTEMS
ASTM D 6621 : 2000 : R2006 Standard Practice for Performance Testing of Process Analyzers for Aromatic Hydrocarbon Materials
ASTM D 3764 : 2015 Standard Practice for Validation of the Performance of Process Stream Analyzer Systems
ASTM D 1072 : 2006 Standard Test Method for Total Sulfur in Fuel Gases by Combustion and Barium Chloride Titration
ASTM D 4810 : 2006 : R2011 Standard Test Method for Hydrogen Sulfide in Natural Gas Using Length-of-Stain Detector Tubes
ASTM D 6621 : 2000 Standard Practice for Performance Testing of Process Analyzers for Aromatic Hydrocarbon Materials
ASTM D 4810 : 1988 : R1999 Standard Test Method for Hydrogen Sulfide in Natural Gas Using Length-of-Stain Detector Tubes
ASTM D 4626 : 1995 : R2019 Standard Practice for Calculation of Gas Chromatographic Response Factors
ASTM D 3606 : 2004 : REV A Standard Test Method for Determination of Benzene and Toluene in Finished Motor and Aviation Gasoline by Gas Chromatography
ASTM D 3606 : 2010 : EDT 1 Standard Test Method for Determination of Benzene and Toluene in Finished Motor and Aviation Gasoline by Gas Chromatography
ASTM D 4810 : 2006 Standard Test Method for Hydrogen Sulfide in Natural Gas Using Length-of-Stain Detector Tubes
ASTM D 1945 : 2003 : R2010 Standard Test Method for Analysis of Natural Gas by Gas Chromatography
ASTM D 3764 : 2009 Standard Practice for Validation of the Performance of Process Stream Analyzer Systems
ASTM D 6122 : 2019 Standard Practice for Validation of the Performance of Multivariate Online, At-Line, and Laboratory Infrared Spectrophotometer Based Analyzer Systems
ASTM D 3606 : 2020 : EDT 1 Standard Test Method for Determination of Benzene and Toluene in Spark Ignition Fuels by Gas Chromatography
ASTM D 5504 : 1998 Standard Test Method for Determination of Sulfur Compounds in Natural Gas and Gaseous Fuels by Gas Chromatography and Chemiluminescence
ASTM D 1945 : 2014 : R2019 Standard Test Method for Analysis of Natural Gas by Gas Chromatography
ASTM D 4468 : 1985 : R2011 Standard Test Method for Total Sulfur in Gaseous Fuels by Hydrogenolysis and<br> Rateometric Colorimetry
ASTM D 1945 : 2003 Standard Test Method for Analysis of Natural Gas by Gas Chromatography
ASTM D 4468 : 1985 : R2006 Standard Test Method for Total Sulfur in Gaseous Fuels by Hydrogenolysis and Rateometric Colorimetry
ASTM D 4626 : 1995 : R2015 Standard Practice for Calculation of Gas Chromatographic Response Factors
ASTM D 5504 : 2001 Standard Test Method for Determination of Sulfur Compounds in Natural Gas and Gaseous Fuels by Gas Chromatography and Chemiluminescence
ASTM D 5504 : 2001 : R2006 Standard Test Method for Determination of Sulfur Compounds in Natural Gas and Gaseous Fuels by Gas Chromatography and Chemiluminescence
ASTM D 4626 : 1995 : R2000 Standard Practice for Calculation of Gas Chromatographic Response Factors
ASTM D 6122 : 2006 : EDT 1 Standard Practice for Validation of the Performance of Multivariate Process Infrared Spectrophotometers
ASTM D 5504 : 2012 Standard Test Method for Determination of Sulfur Compounds in Natural Gas and Gaseous Fuels by Gas Chromatography and Chemiluminescence
ASTM D 3606 : 2021 Standard Test Method for Determination of Benzene and Toluene in Spark Ignition Fuels by Gas Chromatography
ISO 7504:2015 Gas analysis Vocabulary
ASTM D 4810 : 2006 : R2015 Standard Test Method for Hydrogen Sulfide in Natural Gas Using Length-of-Stain Detector Tubes
ASTM D 3606 : 1999 Standard Test Method for Determination of Benzene and Toluene in Finished Motor and Aviation Gasoline by Gas Chromatography
ASTM D 4084 : 2007 : R2012 Standard Test Method for Analysis of Hydrogen Sulfide in Gaseous Fuels (Lead Acetate Reaction Rate Method)
ASTM D 6122 : 1999 Standard Practice for Validation of Multivariate Process Infrared Spectrophotometers
ASTM D 4626 : 1995 : R2010 Standard Practice for Calculation of Gas Chromatographic Response Factors
ASTM D 1945 : 2014 Standard Test Method for Analysis of Natural Gas by Gas Chromatography
ASTM D 4084 : 2007 Standard Test Method for Analysis of Hydrogen Sulfide in Gaseous Fuels (Lead Acetate Reaction Rate Method)
ASTM D 3606 : 1992 Standard Test Method for Determination of Benzene and Toluene in Finished Motor and Aviation Gasoline by Gas Chromatography
ASTM D 1945 : 2014 : REDLINE Standard Test Method for Analysis of Natural Gas by Gas Chromatography
ASTM D 1945 : 1991 Standard Test Method for Analysis of Natural Gas by Gas Chromatography
ASTM D 6122 : 2022 Standard Practice for Validation of the Performance of Multivariate Online, At-Line, Field and Laboratory Infrared Spectrophotometer, and Raman Spectrometer Based Analyzer Systems
ASTM D 6122 : 2009 Standard Practice for Validation of the Performance of Multivariate Process Infrared Spectrophotometers

View more information
£62.61
Excluding VAT

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.