ASTM D 7254 : 2017
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
Hardcopy , PDF
28-08-2020
English
01-06-2017
1.1This specification establishes requirements and test methods for materials, impact strength, appearance, surface flame spread, and wind load resistance of siding products manufactured from polypropylene material. Methods of indicating compliance with this specification are also provided.
1.2The use of polypropylene recycled plastic in this product shall be in accordance with the requirements in Section 4.
1.3Siding produced to this specification shall be installed in accordance with manufacturer’s installation instructions for the specific product to be installed.
Note 1:Information with regard to siding maintenance shall be obtained from the manufacturer.
1.4The values stated in inch-pound units are to be regarded as the standard. The SI units given in parentheses are for information purposes only.
1.5The following precautionary caveat pertains to the test method portion only, Section 6 of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Note 2:There is no known ISO equivalent to this standard.
1.6This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| Committee |
D 20
|
| DocumentType |
Standard
|
| Pages |
7
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| ASTM D 1600 : 1999 | Standard Terminology for Abbreviated Terms Relating to Plastics |
| ASTM D 4101 : 2001 : REV A | Standard Specification for Polypropylene Injection and Extrusion Materials |
| ASTM D 4101 : 2001 | Standard Specification for Polypropylene Injection and Extrusion Materials |
| ASTM D 4101 : 2006 : REV B | Standard Specification for Polypropylene Injection and Extrusion Materials |
| ASTM D 4101 : 2005 | Standard Specification for Polypropylene Injection and Extrusion Materials |
| ASTM D 4101 : 2000 | Standard Specification for Polypropylene Injection and Extrusion Materials |
| ASTM D 1435 : 2013 | Standard Practice for Outdoor Weathering of Plastics |
| ASTM D 3679 : 2006 | Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Siding |
| ASTM D 4101 : 2008 | Standard Specification for Polypropylene Injection and Extrusion Materials |
| ASTM D 3892 : 2015 : R2020 | Standard Practice for Packaging/Packing of Plastics |
| ASTM D 4101 : 2006 | Standard Specification for Polypropylene Injection and Extrusion Materials |
| ASTM D 4101 : 2004 | Standard Specification for Polypropylene Injection and Extrusion Materials |
| ASTM D 4226 : 2005 | Standard Test Methods for Impact Resistance of Rigid Poly(Vinyl Chloride) (PVC) Building Products |
| ASTM D 4101 : 2014 : EDT 2 | Standard Specification for Polypropylene Injection and Extrusion Materials |
| ASTM D 4101 : 2010 | Standard Specification for Polypropylene Injection and Extrusion Materials |
| ASTM D 4101 : 2011 | Standard Specification for Polypropylene Injection and Extrusion Materials |
| ASTM D 4101 : 2005 : REV A | Standard Specification for Polypropylene Injection and Extrusion Materials |
| ASTM D 4226 : 2019 | Standard Test Methods for Impact Resistance of Rigid Poly(Vinyl Chloride) (PVC) Building Products |
| ASTM D 3892 : 1993 : R2003 | Standard Practice for Packaging/Packing of Plastics |
| ASTM D 3892 : 2015 | Standard Practice for Packaging/Packing of Plastics |
| ASTM D 4101 : 2007 | Standard Specification for Polypropylene Injection and Extrusion Materials |
| ASTM D 5206 : 2019 | Standard Test Method for Windload Resistance of Rigid Plastic Siding |
| ASTM D 4101 : 2002 : REV A | Standard Specification for Polypropylene Injection and Extrusion Materials |
| ASTM D 4101 : 2003 : REV B | Standard Specification for Polypropylene Injection and Extrusion Materials |
| ASTM D 3892 : 1993 : R1998 | Standard Practice for Packaging/Packing of Plastics |
| ASTM D 3679 : 2003 : EDT 2 | Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Siding |
| ASTM D 3679 : 2008 | Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Siding |
| ASTM D 4101 : 2002 : REV B | Standard Specification for Polypropylene Injection and Extrusion Materials |
| ASTM D 1600 : 2007 | Standard Terminology for Abbreviated Terms Relating to Plastics |
| ASTM D 1600 : 2013 | Standard Terminology for Abbreviated Terms Relating to Plastics |
| ASTM D 4101 : 2009 | Standard Specification for Polypropylene Injection and Extrusion Materials |
| ASTM D 3679 : 2001 : REV B | Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Siding |
| ASTM D 1600 : 2014 | Standard Terminology for Abbreviated Terms Relating to Plastics |
| ASTM D 4101 : 2006 : REV A | Standard Specification for Polypropylene Injection and Extrusion Materials |
| ASTM D 3679 : 2002 : REV A | Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Siding |
| ASTM D 1600 : 2008 | Standard Terminology for Abbreviated Terms Relating to Plastics |
| ASTM D 3679 : 2009 | Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Siding |
| ASTM D 1435 : 1994 | Standard Practice for Outdoor Weathering of Plastics |
| ASTM D 3679 : 2004 : REV A | Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Siding |
| ASTM D 4101 : 2004 : REV A | Standard Specification for Polypropylene Injection and Extrusion Materials |
| ASTM D 4101 : 1982 : R1988 : EDT 1 | Standard Specification for Propylene Plastic Injection and Extrusion Materials |
| ASTM D 5206 : 2006 : REV A | Standard Test Method for Windload Resistance of Rigid Plastic Siding |
| ASTM D 4101 : 2017 | Standard Classification System and Basis for Specification for Polypropylene Injection and Extrusion Materials |
| ASTM D 3679 : 2004 | Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Siding |
| ASTM D 3679 : 2009 : REV A | Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Siding |
| ASTM D 4101 : 2014 | Standard Specification for Polypropylene Injection and Extrusion Materials |
| ASTM D 3679 : 2017 | Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Siding |
| ASTM D 3679 : 2013 | Standard Specification for Rigid Poly (Vinyl Chloride) (PVC) Siding |
| ASTM D 4226 : 2010 | Standard Test Methods for Impact Resistance of Rigid Poly(Vinyl Chloride) (PVC) Building Products |
| ASTM D 3679 : 2011 | Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Siding |
| ASTM D 1435 : 2005 | Standard Practice for Outdoor Weathering of Plastics |
| ASTM D 3679 : 1999 | Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Siding |
| ASTM D 1600 : 2018 | Standard Terminology for Abbreviated Terms Relating to Plastics (Withdrawn 2024) |
| ASTM D 4101 : 2010 : REV A | Standard Specification for Polypropylene Injection and Extrusion Materials |
| ASTM D 3679 : 2003 | Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Siding |
| ASTM D 4226 : 2016 | Standard Test Methods for Impact Resistance of Rigid Poly(Vinyl Chloride) (PVC) Building Products |
| ASTM D 3679 : 2004 : REV A : EDT 1 | Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Siding |
| ASTM D 4101 : 2003 | Standard Specification for Polypropylene Injection and Extrusion Materials |
| ASTM D 3679 : 2005 | Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Siding |
| ASTM D 4101 : 2003 : REV A | Standard Specification for Polypropylene Injection and Extrusion Materials |
| ASTM D 3679 : 2002 | Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Siding |
| ASTM D 5206 : 1996 | Standard Test Method for Windload Resistance of Rigid Poly(Vinyl Chloride) (PVC) Siding |
| ASTM D 3892 : 1993 : R2009 | Standard Practice for Packaging/Packing of Plastics |
| ASTM D 4226 : 2000 | Standard Test Methods for Impact Resistance of Rigid Poly(Vinyl Chloride) (PVC) Building Products |
| ASTM D 5206 : 2013 | Standard Test Method for Windload Resistance of Rigid Plastic Siding |
| ASTM D 4101 : 2002 | Standard Specification for Polypropylene Injection and Extrusion Materials |
| ASTM D 3679 : 2001 : REV A | Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Siding |
| ASTM D 4101 : 2017 : EDT 1 | Standard Classification System and Basis for Specification for Polypropylene Injection and Extrusion Materials |
| ASTM D 3679 : 2003 : EDT 1 | Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Siding |
| ASTM D 4101 : 2014 : EDT 1 | Standard Specification for Polypropylene Injection and Extrusion Materials |
| ASTM D 3679 : 2001 : REV C | Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Siding |
| ASTM D 4226 : 2009 | Standard Test Methods for Impact Resistance of Rigid Poly(Vinyl Chloride) (PVC) Building Products |
| ASTM D 3679 : 2001 | Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Siding |
| ASTM D 1435 : 1999 | Standard Practice for Outdoor Weathering of Plastics |
| ASTM D 4226 : 2011 | Standard Test Methods for Impact Resistance of Rigid Poly(Vinyl Chloride) (PVC) Building Products |
| ASTM D 3679 : 2006 : REV A | Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Siding |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.