• There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

ASTM D 7273/D7273M : 2008 : R2013 : EDT 1

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Standard Guide for for Acceptance Testing Requirements for Geonets and Geonet Drainage Geocomposites
Available format(s)

Hardcopy , PDF

Superseded date

18-08-2020

Language(s)

English

Published date

01-05-2013

CONTAINED IN VOL. 04.13, 2018 Defines guidelines for the acceptance testing frequency requirements for geonet and geonet drainage geo-composite materials describing types of tests, test methods, and recommended verifications.

1.1This guide covers guidelines for the acceptance testing frequency requirements for geonet and geonet drainage geocomposite materials describing types of tests, test methods, and recommended verifications.

1.2This guide is intended to aid purchasers, installers, contractors, owners, operators, designers, and agencies in establishing a minimum level of effort for product acceptance testing and verification. This is intended to assure that the supplied geonet and/or geonet drainage geocomposite roll(s) meet accepted material specifications.

1.3This guide offers an organized collection of information or a series of options and does not recommend a specific course of action. This guide cannot replace education or experience and should be used in conjunction with professional judgment. Not all aspects of this guide may be applicable in all circumstances. This guide is not intended to represent or replace the standard of care by which the adequacy of a given professional service must be judged, nor should this guide be applied without consideration of a project's many unique aspects. The word "Standard" in the title of this guide means only that the guide has been approved through the ASTM International consensus process.

1.4The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

1.5This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Committee
D 35
DevelopmentNote
Supersedes ASTM D 7273. (06/2013)
DocumentType
Guide
Pages
4
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy
Supersedes

ASCE/EWRI 12-13, 13-13, 14-13 : 2013 STANDARD GUIDELINES FOR THE DESIGN, INSTALLATION, AND OPERATION AND MAINTENANCE OF URBAN SUBSURFACE DRAINAGE
ASTM D 7931 : 2018 : REDLINE Standard Guide for Specifying Drainage Geocomposites

ASTM D 5321 : 2002 Standard Test Method for Determining the Coefficient of Soil and Geosynthetic or Geosynthetic and Geosynthetic Friction by the Direct Shear Method
ASTM D 4759 : 2011 Standard Practice for Determining the Specification Conformance of Geosynthetics
ASTM D 4439 : 2020 Standard Terminology for Geosynthetics
ASTM D 4439 : 2015 Standard Terminology for Geosynthetics
ASTM D 4873 : 1997 Standard Guide for Identification, Storage, and Handling of Geosynthetic Rolls and Samples
ASTM D 4354 : 2012 Standard Practice for Sampling of Geosynthetics and Rolled Erosion Control Products(RECPs) for Testing
ASTM D 4751 : 2016 : REDLINE Standard Test Methods for Determining Apparent Opening Size of a Geotextile
ASTM D 4218 : 2020 Standard Test Method for Determination of Carbon Black Content in Polyethylene Compounds by the Muffle-Furnace Technique
ASTM D 5199 : 2012 : R2019 Standard Test Method for Measuring the Nominal Thickness of Geosynthetics
ASTM D 4355 : 2007 Standard Test Method for Deterioration of Geotextiles by Exposure to Light, Moisture and Heat in a Xenon Arc Type Apparatus
ASTM D 4716 : 2008 : R2013 Standard Test Method for Determining the (In-plane) Flow Rate per Unit Width and Hydraulic Transmissivity of a Geosynthetic Using a Constant Head
ASTM D 1603 : 2001 Standard Test Method for Carbon Black In Olefin Plastics
ASTM D 4533 : 2004 : R2009 Standard Test Method for Trapezoid Tearing Strength of Geotextiles
ASTM D 4873 : 2001 Standard Guide for Identification, Storage, and Handling of Geosynthetic Rolls and Samples
ASTM D 4491 : 1999 : REV A : R2009 Standard Test Methods for Water Permeability of Geotextiles by Permittivity
ASTM D 4533 : 2011 Standard Test Method for Trapezoid Tearing Strength of Geotextiles
ASTM D 4533 : 2004 Standard Test Method for Trapezoid Tearing Strength of Geotextiles
ASTM D 7005 : 2003 Standard Test Method for Determining the Bond Strength (Ply Adhesion) of Geocomposites
ASTM D 5321 : 2008 Standard Test Method for Determining the Coefficient of Soil and Geosynthetic or Geosynthetic and Geosynthetic Friction by the Direct Shear Method
ASTM D 4355 : 1999 Standard Test Method for Deterioration of Geotextiles from Exposure to Ultraviolet Light and Water (Xenon-Arc Type Apparatus)
ASTM D 4354 : 2012 : R2020 Standard Practice for Sampling of Geosynthetics and Rolled Erosion Control Products (RECPs) for Testing
ASTM D 4533 : 1991 : R1996 Standard Test Method for Trapezoid Tearing Strength of Geotextiles
ASTM D 4218 : 1996 : R2001 Standard Test Method for Determination of Carbon Black Content in Polyethylene Compounds By the Muffle-Furnace Technique
ASTM D 4716 : 2000 Test Method for Determining the (In-plane) Flow Rate per Unit Width and Hydraulic Transmissivity of a Geosynthetic Using a Constant Head
ASTM D 4439 : 2011 Standard Terminology for Geosynthetics
ASTM D 7179 : 2007 : R2013 Standard Test Method for Determining Geonet Breaking Force
ASTM D 4873 : 2002 Standard Guide for Identification, Storage, and Handling of Geosynthetic Rolls and Samples
ASTM D 6241 : 2014 : REDLINE Standard Test Method for Static Puncture Strength of Geotextiles and Geotextile-Related Products Using a 50-mm Probe
ASTM D 1505 : 2003 Standard Test Method for Density of Plastics by the Density-Gradient Technique
ASTM D 4716 : 2002 Test Method for Determining the (In-plane) Flow Rate per Unit Width and Hydraulic Transmissivity of a Geosynthetic Using a Constant Head
ASTM D 5199 : 2001 Standard Test Method for Measuring the Nominal Thickness of Geosynthetics
ASTM D 792 : 2013 : REDLINE Standard Test Methods for Density and Specific Gravity (Relative Density) of Plastics by Displacement
ASTM D 7179 : 2007 Standard Test Method for Determining Geonet Breaking Force
ASTM D 4439 : 2015 : REV A Standard Terminology for Geosynthetics
ASTM D 4218 : 1996 : R2008 Standard Test Method for Determination of Carbon Black Content in Polyethylene Compounds By the Muffle-Furnace Technique
ASTM D 4751 : 1999 : REV A Standard Test Method for Determining Apparent Opening Size of a Geotextile
ASTM D 4751 : 2004 Standard Test Method for Determining Apparent Opening Size of a Geotextile
ASTM D 4491 : 1999 : REV A : R2004 : EDT 1 Standard Test Methods for Water Permeability of Geotextiles by Permittivity
ASTM D 4759 : 2011 : R2018 Standard Practice for Determining the Specification Conformance of Geosynthetics
ASTM D 4439 : 2002 Standard Terminology for Geosynthetics
ASTM D 4632 : 1991 : R1996 Standard Test Method for Grab Breaking Load and Elongation of Geotextiles
ASTM D 1603 : 2020 Standard Test Method for Carbon Black Content in Olefin Plastics
ASTM D 5321 : 2012 Standard Test Method for Determining the Shear Strength of Soil-Geosynthetic and Geosynthetic-Geosynthetic Interfaces by Direct Shear
ASTM D 1603 : 2011 Standard Test Method for Carbon Black Content in Olefin Plastics
ASTM D 4759 : 2002 Standard Practice for Determining the Specification Conformance of Geosynthetics
ASTM D 1603 : 2014 : REDLINE Standard Test Method for Carbon Black Content in Olefin Plastics
ASTM D 4439 : 2017 Standard Terminology for Geosynthetics
ASTM D 4751 : 1999 : REV A : R2004 Standard Test Method for Determining Apparent Opening Size of a Geotextile
ASTM D 4716 : 2008 Standard Test Method for Determining the (In-plane) Flow Rate per Unit Width and Hydraulic Transmissivity of a Geosynthetic Using a Constant Head
ASTM D 4873 : 2015 Standard Guide for Identification, Storage, and Handling of Geosynthetic Rolls and Samples
ASTM D 4716 : 2004 Test Method for Determining the (In-plane) Flow Rate per Unit Width and Hydraulic Transmissivity of a Geosynthetic Using a Constant Head
ASTM D 1603 : 1994 Standard Test Method for Carbon Black In Olefin Plastics
ASTM D 4491 : 1999 : REV A : R2014 : EDT 1 Standard Test Methods for Water Permeability of Geotextiles by Permittivity
ASTM D 4716 : 2003 Test Method for Determining the (In-plane) Flow Rate per Unit Width and Hydraulic Transmissivity of a Geosynthetic Using a Constant Head
ASTM D 1603 : 2006 Standard Test Method for Carbon Black Content in Olefin Plastics
ASTM D 7005 : 2003 : R2008 Standard Test Method for Determining the Bond Strength (Ply Adhesion) of Geocomposites
ASTM D 1505 : 1968 : R1979 Standard Test Method for Density Of Plastics By The Density-Gradient Technique
ASTM D 4218 : 2015 Standard Test Method for Determination of Carbon Black Content in Polyethylene Compounds By the Muffle-Furnace Technique
ASTM D 4716 : 2007 Standard Test Method for Determining the (In-plane) Flow Rate per Unit Width and Hydraulic Transmissivity of a Geosynthetic Using a Constant Head
ASTM D 6241 : 2014 Standard Test Method for Static Puncture Strength of Geotextiles and Geotextile-Related Products Using a 50-mm Probe
ASTM D 4759 : 2002 : R2007 Standard Practice for Determining the Specification Conformance of Geosynthetics
ASTM D 4751 : 2012 Standard Test Method for Determining Apparent Opening Size of a Geotextile
ASTM D 4439 : 2001 Standard Terminology for Geosynthetics
ASTM D 6241 : 2004 : R2009 Standard Test Method for the Static Puncture Strength of Geotextiles and Geotextile-Related Products Using a 50-mm Probe
ASTM D 4439 : 2014 Standard Terminology for Geosynthetics
ASTM D 4354 : 1999 : R2009 Standard Practice for Sampling of Geosynthetics for Testing
ASTM D 6241 : 1999 Standard Test Method for the Static Puncture Strength of Geotextiles and Geotextile-Related Products Using a 50-mm Probe
ASTM D 5199 : 2012 Standard Test Method for Measuring the Nominal Thickness of Geosynthetics
ASTM D 4354 : 2012 : REDLINE Standard Practice for Sampling of Geosynthetics and Rolled Erosion Control Products(RECPs) for Testing
ASTM D 1505 : 2010 Standard Test Method for Density of Plastics by the Density-Gradient Technique
ASTM D 1505 : 2018 Standard Test Method for Density of Plastics by the Density-Gradient Technique
ASTM D 5199 : 2011 Standard Test Method for Measuring the Nominal Thickness of Geosynthetics
ASTM D 4354 : 1999 Standard Practice for Sampling of Geosynthetics for Testing
ASTM D 4759 : 1988 : R1996 Standard Practice for Determining the Specification Conformance of Geosynthetics
ASTM D 4439 : 2004 Standard Terminology for Geosynthetics
ASTM D 1505 : 1998 : EDT 1 Standard Test Method for Density of Plastics by the Density-Gradient Technique
ASTM D 6241 : 2004 Standard Test Method for the Static Puncture Strength of Geotextiles and Geotextile-Related Products Using a 50-mm Probe
ASTM D 4873 : 2002 : R2009 Standard Guide for Identification, Storage, and Handling of Geosynthetic Rolls and Samples
ASTM D 4632 : 2008 Standard Test Method for Grab Breaking Load and Elongation of Geotextiles
ASTM D 1603 : 2014 Standard Test Method for Carbon Black Content in Olefin Plastics
ASTM D 4439 : 2017-08 TERMINOLOGY FOR GEOSYNTHETICS
ASTM D 1603 : 2012 Standard Test Method for Carbon Black Content in Olefin Plastics
ASTM D 6241 : 2004 : R2009 : EDT 1 Standard Test Method for the Static Puncture Strength of Geotextiles and Geotextile-Related Products Using a 50-mm Probe
ASTM D 4751 : 2016 Standard Test Methods for Determining Apparent Opening Size of a Geotextile
ASTM D 4355 : 2002 Standard Test Method for Deterioration of Geotextiles by Exposure to Light, Moisture and Heat in a Xenon Arc Type Apparatus
ASTM D 5199 : 2001 : R2006 Standard Test Method for Measuring the Nominal Thickness of Geosynthetics
ASTM D 4439 : 2000 Standard Terminology for Geosynthetics
ASTM D 4491 : 1999 : REV A Standard Test Methods for Water Permeability of Geotextiles by Permittivity
ASTM D 4355 : 2005 Standard Test Method for Deterioration of Geotextiles by Exposure to Light, Moisture and Heat in a Xenon Arc Type Apparatus
ASTM D 4491 : 1999 : REV A : R2004 Standard Test Methods for Water Permeability of Geotextiles by Permittivity
ASTM D 7179 : 2007 : EDT 1 Standard Test Method for Determining Geonet Breaking Force
ASTM D 4716 : 2001 Test Method for Determining the (In-plane) Flow Rate per Unit Width and Hydraulic Transmissivity of a Geosynthetic Using a Constant Head
ASTM D 4354 : 1999 : R2004 Standard Practice for Sampling of Geosynthetics for Testing
ASTM D 4632 : 1991 : R2003 Standard Test Method for Grab Breaking Load and Elongation of Geotextiles
ASTM D 7179 : 2005 Standard Test Method for Determining Geonet Breaking Force
ASTM D 4439 : 2018 Standard Terminology for Geosynthetics
ASTM D 7179 : 2018 Standard Test Method for Determining Geonet Breaking Force
ASTM D 5321 : 1992 : R1997 Standard Test Method for Determining the Coefficient of Soil and Geosynthetic or Geosynthetic and Geosynthetic Friction by the Direct Shear Method
ASTM D 4218 : 1996 Standard Test Method for Determination of Carbon Black Content in Polyethylene Compounds By the Muffle-Furnace Technique

View more information
£55.10
Excluding VAT

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.