ASTM D 7291/D7291M : 2015
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
Standard Test Method for Through-Thickness “Flatwise” Tensile Strength and Elastic Modulus of a Fiber-Reinforced Polymer Matrix Composite Material
Hardcopy , PDF
21-11-2022
English
09-11-2015
This test method determines the through-thickness “flatwise” tension strength and elastic modulus of fiber reinforced polymer matrix composite materials.
1.1This test method determines the through-thickness “flatwise” tension strength and elastic modulus of fiber reinforced polymer matrix composite materials. A tensile force is applied normal to the plane of the composite laminate using adhesively bonded thick metal end-tabs. The composite material forms are limited to continuous-fiber or discontinuous fiber (tape or 2-dimensional fabric, or both) reinforced composites.
1.2The through-thickness strength results using this test method will in general not be comparable to Test Method D6415 since this method subjects a relatively large volume of material to an almost uniform stress field while Test Method D6415 subjects a small volume of material to a non-uniform stress field.
1.3The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text, the inch-pound units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.
1.4This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
| Committee |
D 30
|
| DocumentType |
Test Method
|
| Pages |
12
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| ASTM D 4762 : 2018 | Standard Guide for Testing Polymer Matrix Composite Materials |
| ASTM D 3171 : 1999 | Standard Test Methods for Constituent Content of Composite Materials |
| ASTM E 177 : 1990 : REV A : R1996 | Standard Practice for Use of the Terms Precision and Bias in ASTM Test Methods |
| ASTM E 1012 : 2014 | Standard Practice for Verification of Testing Frame and Specimen Alignment Under Tensile and Compressive Axial Force Application |
| ASTM E 456 : 2002 | Standard Terminology for Relating to Quality and Statistics |
| ASTM D 3878 : 2002 : REV A | Standard Terminology for Composite Materials |
| ASTM E 456 : 2013 : REV A : R2022 | Standard Terminology Relating to Quality and Statistics |
| ASTM D 3878 : 2015 | Standard Terminology for Composite Materials |
| ASTM E 1434 : 2000 : R2013 | Standard Guide for Recording Mechanical Test Data of Fiber-Reinforced Composite Materials in Databases (Withdrawn 2015) |
| ASTM D 3878 : 2019 | Standard Terminology for Composite Materials |
| ASTM D 3878 : 2000 | Standard Terminology Composite Materials |
| ASTM D 3171 : 2011 | Standard Test Methods for Constituent Content of Composite Materials |
| ASTM E 6 : 2002 | Standard Terminology Relating to Methods of Mechanical Testing |
| ASTM E 691 : 2020 | Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method |
| ASTM E 1012 : 1999 | Standard Practice for Verification of Specimen Alignment Under Tensile Loading |
| ASTM E 1012 : 2012 | Standard Practice for Verification of Testing Frame and Specimen Alignment Under Tensile and Compressive Axial Force Application |
| ASTM E 456 : 2013 : REV A : R2017 : EDT 5 | Standard Terminology Relating to Quality and Statistics |
| ASTM E 122 : 2017 : R2022 | Standard Practice for Calculating Sample Size to Estimate, With Specified Precision, the Average for a Characteristic of a Lot or Process |
| ASTM E 122 : 2017 | Standard Practice for Calculating Sample Size to Estimate, With Specified Precision, the Average for a Characteristic of a Lot or Process |
| ASTM E 1012 : 2014 : EDT 1 | Standard Practice for Verification of Testing Frame and Specimen Alignment Under Tensile and Compressive Axial Force Application |
| ASTM E 1471 : 1992 : R2008 | Standard Guide for Identification of Fibers, Fillers, and Core Materials in Computerized Material Property Databases |
| ASTM D 3878 : 2003 : REV A | Standard Terminology for Composite Materials |
| ASTM E 691 : 2019 : EDT 1 | Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method |
| ASTM D 3878 : 2016 | Standard Terminology for Composite Materials |
| ASTM E 1309 : 2000 | Standard Guide for Identification of Fiber-Reinforced Polymer-Matrix Composite Materials in Databases |
| ASTM E 1471 : 1992 : R1998 | Standard Guide for Identification of Fibers, Fillers, and Core Materials in Computerized Material Property Databases |
| ASTM D 3878 : 2019 : REV A | Standard Terminology for Composite Materials |
| ASTM D 3878 : 2020 : REV A | Standard Terminology for Composite Materials |
| ASTM D 3878 : 1998 | Standard Terminology Composite Materials |
| ASTM D 3171 : 2022 | Standard Test Methods for Constituent Content of Composite Materials |
| ASTM D 3878 : 2018 | Standard Terminology for Composite Materials |
| ASTM E 691 : 2022 | Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method |
| ASTM E 1012 : 2012 : EDT 1 | Standard Practice for Verification of Testing Frame and Specimen Alignment Under Tensile and Compressive Axial Force Application |
| ASTM E 1434 : 2000 | Standard Guide for Recording Mechanical Test Data of Fiber-Reinforced Composite Materials in Databases |
| ASTM D 3171 : 2009 | Standard Test Methods for Constituent Content of Composite Materials |
| ASTM E 691 : 2009 | Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method |
| ASTM D 3878 : 2002 | Standard Terminology for Composite Materials |
| ASTM E 6 : 2015 : EDT 3 | Standard Terminology Relating to Methods of Mechanical Testing |
| ASTM E 1471 : 1992 : R2014 | Standard Guide for Identification of Fibers, Fillers, and Core Materials in Computerized Material Property Databases (Withdrawn 2015) |
| ASTM E 1012 : 2005 | Standard Practice for Verification of Test Frame and Specimen Alignment Under Tensile and Compressive Axial Force Application |
| ASTM D 3878 : 2004 | Standard Terminology for Composite Materials |
| ASTM E 4 : 2021 | Standard Practices for Force Calibration and Verification of Testing Machines |
| ASTM E 691 : 2021 | Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method |
| ASTM D 3878 : 2007 : R2013 | Standard Terminology for Composite Materials |
| ASTM E 1309 : 2000 : R2011 | Standard Guide for Identification of Fiber-Reinforced Polymer-Matrix Composite Materials in Databases (Withdrawn 2015) |
| ASTM D 3878 : 2020 : REDLINE | Standard Terminology for Composite Materials |
| ASTM D 3878 : 2020 | Standard Terminology for Composite Materials |
| ASTM E 1471 : 1992 : R2004 | Standard Guide for Identification of Fibers, Fillers, and Core Materials in Computerized Material Property Databases |
| ASTM D 3878 : 2003 | Standard Terminology for Composite Materials |
| ASTM E 6 : 2015 : EDT 4 : REDLINE | Standard Terminology Relating to Methods of Mechanical Testing |
| ASTM D 3878 : 2007 | Standard Terminology for Composite Materials |
| ASTM D 3171 : 1999 : R2004 | Standard Test Methods for Constituent Content of Composite Materials |
| ASTM D 6415 : 1999 : EDT 1 | Standard Test Method for Measuring the Curved Beam Stength of a Fiber-Reinforced Polymer-Matrix Composite |
| ASTM E 1309 : 2000 : R2005 | Standard Guide for Identification of Fiber-Reinforced Polymer-Matrix Composite Materials in Databases |
| ASTM D 3171 : 2015 | Standard Test Methods for Constituent Content of Composite Materials |
| ASTM E 456 : 2013 : REV A : R2017 : EDT 4 | Standard Terminology Relating to Quality and Statistics |
| ASTM E 456 : 2013 : REV A : R2017 : EDT 6 | Standard Terminology Relating to Quality and Statistics |
| ASTM D 3878 : 2004 : REV A | Standard Terminology for Composite Materials |
| ASTM D 3171 : 2006 | Standard Test Methods for Constituent Content of Composite Materials |
| ASTM E 1012 : 2019 | Standard Practice for Verification of Testing Frame and Specimen Alignment Under Tensile and Compressive Axial Force Application |
| ASTM E 1434 : 2000 : R2006 | Standard Guide for Recording Mechanical Test Data of Fiber-Reinforced Composite Materials in Databases |
| ASTM D 3878 : 2001 | Standard Terminology Composite Materials |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.