• There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

ASTM D 7590 : 2009 : R2014

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Standard Guide for Measurement of Remaining Primary Antioxidant Content In In-Service Industrial Lubricating Oils by Linear Sweep Voltammetry
Available format(s)

Hardcopy , PDF

Superseded date

23-12-2022

Language(s)

English

Published date

25-07-2014

CONTAINED IN VOL. 05.04, 2017 Defines the voltammetric analysis for qualitative measurements of primary antioxidants in new or inservice type industrial lubricants detectable in concentrations as low as 0.0075 mass percent up to concentrations found in new oils by measuring the amount of current flow at a specified voltage in the produced voltammogram.

1.1This guide covers the voltammetric analysis for qualitative measurements of primary antioxidants in new or in-service type industrial lubricants detectable in concentrations as low as 0.0075 mass percent up to concentrations found in new oils by measuring the amount of current flow at a specified voltage in the produced voltammogram.

1.2This guide can be used as a resource for a condition monitoring program to track the oxidative health of a range of industrial lubricants which contain primary antioxidants. In order to avoid excessive degradation of the base-oil, these primary antioxidants play a major role to protect the lubricants against thermal-oxidative degradation. This guide can help users with interpretation and troubleshooting results obtained using linear sweep voltammetry (LSV).

1.3When used as part of oil condition monitoring practices, it is important to apply trend analysis to monitor the antioxidant depletion rate relative to a baseline sample rather than use voltammetry for an absolute measurement of the antioxidant concentration. The trending pattern provides a proactive means to identify the level of oil degradation or abnormal changes in the condition of the in-service lubricant.

1.4The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.

1.5This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Committee
D 02
DocumentType
Guide
Pages
14
ProductNote
Reconfirmed 2014
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy
Supersedes

ASTM D 4057 : 2019 Standard Practice for Manual Sampling of Petroleum and Petroleum Products
ASTM D 4378 : 2003 Standard Practice for In-Service Monitoring of Mineral Turbine Oils for Steam and Gas Turbines
ASTM D 4057 : 1995 Standard Practice for Manual Sampling of Petroleum and Petroleum Products
ASTM D 6224 : 2022 Standard Practice for In-Service Monitoring of Lubricating Oil for Auxiliary Power Plant Equipment
ASTM D 6971 : 2022 Standard Test Method for Measurement of Hindered Phenolic and Aromatic Amine Antioxidant Content in Non-zinc Turbine Oils by Linear Sweep Voltammetry
ASTM D 7214 : 2007 : REV A : R2019 Standard Test Method for Determination of the Oxidation of Used Lubricants by FT-IR Using Peak Area Increase Calculation
ASTM D 4057 : 2012 : R2018 Standard Practice for Manual Sampling of Petroleum and Petroleum Products
ASTM D 6304:2016 Standard Test Method for Determination of Water in Petroleum Products, Lubricating Oils, and Additives by Coulometric Karl Fischer Titration
ASTM D 6224 : 2016 Standard Practice for In-Service Monitoring of Lubricating Oil for Auxiliary Power Plant Equipment
ASTM D 4378 : 2012 Standard Practice for In-Service Monitoring of Mineral Turbine Oils for Steam, Gas, and Combined Cycle Turbines
ASTM D 6971 : 2009 : R2014 Standard Test Method for Measurement of Hindered Phenolic and Aromatic Amine Antioxidant Content in Non-zinc Turbine Oils by Linear Sweep Voltammetry
ASTM D 6304 : 2004 : REV A : EDT 1 Standard Test Method for Determination of Water in Petroleum Products, Lubricating Oils, and Additives by Coulometric Karl Fisher Titration
ASTM D 1193 : 1977 : R1983 : EDT 1 Standard Specification for Reagent Water
ASTM D 6224 : 1998 Standard Practice for In-Service Monitoring of Lubricating Oil for Auxiliary Power Plant Equipment
ASTM D 7214 : 2007 Standard Test Method for Determination of the Oxidation of Used Lubricants by FT-IR Using Peak Area Increase Calculation
ASTM D 4057 : 1981 : EDT 2 Standard Practice for Manual Sampling of Petroleum and Petroleum Products
ASTM D 6810 : 2002 Standard Test Method for Measurement of Hindered Phenolic Antioxidant Content in HL Turbine Oils by Linear Sweep Voltammetry
ASTM D 6971 : 2009 Standard Test Method for Measurement of Hindered Phenolic and Aromatic Amine Antioxidant Content in Non-zinc Turbine Oils by Linear Sweep Voltammetry
ASTM D 6304 : 2007 Standard Test Method for Determination of Water in Petroleum Products, Lubricating Oils, and Additives by Coulometric Karl Fischer Titration (Withdrawn 2016)
ASTM D 6304 : 2004 Standard Test Method for Determination of Water in Petroleum Products, Lubricating Oils, and Additives by Coulometric Karl Fisher Titration
ASTM D 6810 : 2013 Standard Test Method for Measurement of Hindered Phenolic Antioxidant Content in Non-Zinc Turbine Oils by Linear Sweep Voltammetry
ASTM D 6304 : 2016 : EDT 1 Standard Test Method for Determination of Water in Petroleum Products, Lubricating Oils, and Additives by Coulometric Karl Fischer Titration
ASTM D 4378 : 2020 Standard Practice for In-Service Monitoring of Mineral Turbine Oils for Steam, Gas, and Combined Cycle Turbines
ASTM D 6304 : 2004 : REV A Standard Test Method for Determination of Water in Petroleum Products, Lubricating Oils, and Additives by Coulometric Karl Fisher Titration
ASTM D 6304 : 2004 : EDT 1 Standard Test Method for Determination of Water in Petroleum Products, Lubricating Oils, and Additives by Coulometric Karl Fisher Titration
ASTM D 6224 : 2002 Standard Practice for In-Service Monitoring of Lubricating Oil for Auxiliary Power Plant Equipment
ASTM D 4057 : 2006 Standard Practice for Manual Sampling of Petroleum and Petroleum Products
ASTM D 1193 : 2006 : R2011 Standard Specification for Reagent Water
ASTM D 6304 : 2000 Standard Test Method for Determination of Water in Petroleum Products, Lubricating Oils, and Additives by Coulometric Karl Fisher Titration
ASTM D 4057 : 2012 Standard Practice for Manual Sampling of Petroleum and Petroleum Products
ASTM D 7214 : 2006 Standard Test Method for Determination of the Oxidation of Used Lubricants by FT-IR Using Peak Area Increase Calculation
ASTM D 7214 : 2022 Standard Test Method for Determination of the Oxidation of Used Lubricants by FT-IR Using Peak Area Increase Calculation
ASTM D 1193 : 1991 Standard Specification for Reagent Water
ASTM D 7214 : 2007 : REV A : R2012 Standard Test Method for Determination of the Oxidation of Used Lubricants by FT-IR Using Peak Area Increase Calculation
ASTM D 6810 : 2022 Standard Test Method for Measurement of Hindered Phenolic Antioxidant Content in Non-Zinc Turbine Oils by Linear Sweep Voltammetry
ASTM D 6810 : 2007 Standard Test Method for Measurement of Hindered Phenolic Antioxidant Content in Non-Zinc Turbine Oils by Linear Sweep Voltammetry
ASTM D 4378 : 2022 Standard Practice for In-Service Monitoring of Mineral Turbine Oils for Steam, Gas, and Combined Cycle Turbines
ASTM D 6224 : 2009 Standard Practice for In-Service Monitoring of Lubricating Oil for Auxiliary Power Plant Equipment
ASTM D 4378 : 2013 Standard Practice for In-Service Monitoring of Mineral Turbine Oils for Steam, Gas, and Combined Cycle Turbines
ASTM D 6304 : 2003 Standard Test Method for Determination of Water in Petroleum Products, Lubricating Oils, and Additives by Coulometric Karl Fisher Titration
ASTM D 4378 : 2008 Standard Practice for In-Service Monitoring of Mineral Turbine Oils for Steam and Gas Turbines
ASTM D 6971 : 2004 Standard Test Method for Measurement of Hindered Phenolic and Aromatic Amine Antioxidant Content in Non-zinc Turbine Oils by Linear Sweep Voltammetry
ASTM D 4057 : 2022 Standard Practice for Manual Sampling of Petroleum and Petroleum Products
VGB M 416 : 2010 PART A: IN-SERVICE MONITORING OF TURBINE OILS FOR STEAM AND GAS TURBINES - PART B: IN-SERVICE MONITORING OF FIRE RESISTANT FLUIDS FOR STEAM AND GAS TURBINES
ASTM D 1193 : 1970 Standard Specification For Reagent Water
ASTM D 4378 : 1997 Standard Practice for In-Service Monitoring of Mineral Turbine Oils for Steam and Gas Turbines
ASTM D 7214 : 2020 Standard Test Method for Determination of the Oxidation of Used Lubricants by FT-IR Using Peak Area Increase Calculation
ASTM D 1193 : 2006 Standard Specification for Reagent Water
ASTM D 1193 : 1999 Standard Specification for Reagent Water
ASTM D 4057 : 1995 : R2000 Standard Practice for Manual Sampling of Petroleum and Petroleum Products
ASTM D 7214 : 2007 : REV A Standard Test Method for Determination of the Oxidation of Used Lubricants by FT-IR Using Peak Area Increase Calculation
ASTM D 6224 : 2016 : REDLINE Standard Practice for In-Service Monitoring of Lubricating Oil for Auxiliary Power Plant Equipment
ASTM D 1193 : 2006 : R2018 Standard Specification for Reagent Water
ASTM D 4057 : 2006 : R2011 Standard Practice for Manual Sampling of Petroleum and Petroleum Products
ASTM D 6810 : 2013 : REDLINE Standard Test Method for Measurement of Hindered Phenolic Antioxidant Content in Non-Zinc Turbine Oils by Linear Sweep Voltammetry
ASTM D 6810 : 2021 Standard Test Method for Measurement of Hindered Phenolic Antioxidant Content in Non-Zinc Turbine Oils by Linear Sweep Voltammetry

View more information
£69.29
Excluding VAT

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.