• There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

ASTM D 7961 : 2017

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Standard Practice for Calibrating U-tube Density Cells over Large Ranges of Temperature and Pressure
Available format(s)

Hardcopy , PDF

Superseded date

20-12-2022

Language(s)

English

Published date

18-07-2017

1.1This practice outlines procedures for the calibration of U-tube density cells. It is applicable to instruments capable of determining fluid density at temperatures in the range –10 °C to 200 °C and pressures from just greater than the saturation pressure to 140 MPa. The practice refers to density cells as they are utilized to make measurements of fluids primarily in the compressed-liquid state. Examples of substances for which the density can be determined with a calibrated U-tube density meter include: crude oils, gasoline and gasoline-oxygenate blends, diesel and jet fuels, hydraulic fluids, and lubricating oils.

1.2This practice specifies a procedure for the determination of the expanded uncertainty of the density measurement.

1.3This practice pertains to fluids with viscosities < 1 Pa·s (1000 centipoise) at ambient conditions.

1.44 The values listed in SI units are regarded as the standard, unless otherwise stated. The SI unit for mass density is kilograms per cubic metre (kg·m-3) and can be given as grams per cubic centimetre (g·cm-3).

1.5This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Committee
D 02
DocumentType
Standard Practice
Pages
7
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy
Supersedes

ASTM D 6792 : 2021 : REV A Standard Practice for Quality Management Systems in Petroleum Products, Liquid Fuels, and Lubricants Testing Laboratories
ASTM D 7483 : 2013 Standard Test Method for Determination of Dynamic Viscosity and Derived Kinematic Viscosity of Liquids by Oscillating Piston Viscometer
ASTM D 4052 : 1996 : R2002 : EDT 1 Standard Test Method for Density and Relative Density of Liquids by Digital Density Meter
ASTM D 4052 : 2018 : REV A Standard Test Method for Density, Relative Density, and API Gravity of Liquids by Digital Density Meter
ASTM D 5002 : 2016 Standard Test Method for Density and Relative Density of Crude Oils by Digital Density Analyzer
ASTM D 6792 : 2006 Standard Guide for Quality System in Petroleum Products and Lubricants Testing Laboratories
ASTM D 7483 : 2020 Standard Test Method for Determination of Dynamic Viscosity and Derived Kinematic Viscosity of Liquids by Oscillating Piston Viscometer
ASTM D 6792 : 2004 Standard Guide for Quality System in Petroleum Products and Lubricants Testing Laboratories
ASTM D 1193 : 1977 : R1983 : EDT 1 Standard Specification for Reagent Water
ASTM D 5002 : 2015 Standard Test Method for Density and Relative Density of Crude Oils by Digital Density Analyzer
ASTM D 4052 : 2009 Standard Test Method for Density, Relative Density, and API Gravity of Liquids by Digital Density Meter
ASTM D 7578 : 2018 Standard Guide for Calibration Requirements for Elemental Analysis of Petroleum Products and Lubricants
ASTM D 6792 : 2021 : REV B Standard Practice for Quality Management Systems in Petroleum Products, Liquid Fuels, and Lubricants Testing Laboratories
ASTM D 7740 : 201 Standard Practice for Optimization, Calibration, and Validation of Atomic Absorption Spectrometry for Metal Analysis of Petroleum Products and Lubricants
ASTM D 5002 : 2018 : EDT 1 Standard Test Method for Density, Relative Density, and API Gravity of Crude Oils by Digital Density Analyzer
ASTM D 6792 : 2004 : REV A Standard Guide for Quality System in Petroleum Products and Lubricants Testing Laboratories
ASTM D 5002 : 1999 : R2010 Standard Test Method for Density and Relative Density of Crude Oils by Digital Density Analyzer
ASTM D 5002 : 2013 Standard Test Method for Density and Relative Density of Crude Oils by Digital Density Analyzer
ASTM D 6792 : 2005 Standard Guide for Quality System in Petroleum Products and Lubricants Testing Laboratories
ASTM D 1193 : 2006 : R2011 Standard Specification for Reagent Water
ASTM D 6792 : 2020 Standard Practice for Quality Management Systems in Petroleum Products, Liquid Fuels, and Lubricants Testing Laboratories
ASTM D 4052 : 2011 Standard Test Method for Density, Relative Density, and API Gravity of Liquids by Digital Density Meter
ASTM D 6792 : 2021 Standard Practice for Quality Management Systems in Petroleum Products, Liquid Fuels, and Lubricants Testing Laboratories
ASTM D 5002 : 2019 Standard Test Method for Density, Relative Density, and API Gravity of Crude Oils by Digital Density Analyzer
ASTM D 4052 : 2016 Standard Test Method for Density, Relative Density, and API Gravity of Liquids by Digital Density Meter
ASTM D 6792 : 2013 Standard Practice for Quality System in Petroleum Products and Lubricants Testing Laboratories
ASTM D 7578 : 2010 : EDT 1 Standard Guide for Calibration Requirements for Elemental Analysis of Petroleum Products and Lubricants
ASTM D 6792 : 2017 Standard Practice for Quality Management Systems in Petroleum Products, Liquid Fuels, and Lubricants Testing Laboratories
ASTM D 7740 : 2011 : R2016 Standard Practice for Optimization, Calibration, and Validation of Atomic Absorption Spectrometry for Metal Analysis of Petroleum Products and Lubricants
ASTM D 6792 : 2007 Standard Practice for Quality System in Petroleum Products and Lubricants Testing Laboratories
ASTM D 1193 : 1991 Standard Specification for Reagent Water
ASTM D 6792 : 2021 : REV C Standard Practice for Quality Management Systems in Petroleum Products, Liquid Fuels, and Lubricants Testing Laboratories
ASTM D 7578 : 2020 Standard Guide for Calibration Requirements for Elemental Analysis of Petroleum Products and Lubricants
ASTM D 4052 : 1996 Standard Test Method for Density and Relative Density of Liquids by Digital Density Meter
ASTM D 7483 : 2013 : REV A Standard Test Method for Determination of Dynamic Viscosity and Derived Kinematic Viscosity of Liquids by Oscillating Piston Viscometer
ASTM D 6792 : 2022 Standard Practice for Quality Management Systems in Petroleum Products, Liquid Fuels, and Lubricants Testing Laboratories
ASTM D 7578 : 2010 Standard Guide for Calibration Requirements for Elemental Analysis of Petroleum Products and Lubricants
ASTM D 5002 : 1999 : R2005 Standard Test Method for Density and Relative Density of Crude Oils by Digital Density Analyzer
ASTM D 5002 : 2018 Standard Test Method for Density, Relative Density, and API Gravity of Crude Oils by Digital Density Analyzer
ASTM D 4052 : 2022 Standard Test Method for Density, Relative Density, and API Gravity of Liquids by Digital Density Meter
ASTM D 1193 : 1970 Standard Specification For Reagent Water
ASTM D 6792 : 2003 Standard Guide for Quality System in Petroleum Products and Lubricants Testing Laboratories
ASTM D 1193 : 2006 Standard Specification for Reagent Water
ASTM D 7483 : 2008 Standard Test Method for Determination of Dynamic Viscosity and Derived Kinematic Viscosity of Liquids by Oscillating Piston Viscometer
ASTM D 1193 : 1999 Standard Specification for Reagent Water
ASTM D 6792 : 2002 Standard Guide for A Quality System in Petroleum Products and Lubricants Testing Laboratories
ASTM D 4052 : 2015 Standard Test Method for Density, Relative Density, and API Gravity of Liquids by Digital Density Meter
ASTM D 5002 : 2022 Standard Test Method for Density, Relative Density, and API Gravity of Crude Oils by Digital Density Analyzer
ASTM D 1193 : 2006 : R2018 Standard Specification for Reagent Water
ASTM D 7578 : 2015 Standard Guide for Calibration Requirements for Elemental Analysis of Petroleum Products and Lubricants
ASTM D 7483 : 2013 : REV A : R2017 Standard Test Method for Determination of Dynamic Viscosity and Derived Kinematic Viscosity of Liquids by Oscillating Piston Viscometer
ASTM D 4052 : 2018 Standard Test Method for Density, Relative Density, and API Gravity of Liquids by Digital Density Meter
ASTM D 5002 : 1999 Standard Test Method for Density and Relative Density of Crude Oils by Digital Density Analyzer

View more information
£62.61
Excluding VAT

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.