ASTM D 8066/D8066M : 2017
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
Hardcopy , PDF
24-06-2023
English
15-09-2017
CONTAINED IN VOL. 15.03, 2017 Gives instructions for using the Test Method D 6484 open hole compression test fixture to determine unnotched compressive strength of multi-directional laminates.
1.1This practice provides instructions for using the Test Method D6484 open hole compression test fixture to determine unnotched compressive strength of multi-directional laminates. The composite material forms are limited to continuous-fiber reinforced polymer matrix composites in which the laminate is both symmetric and balanced with respect to the test direction. The range of acceptable test laminates and thicknesses are described in 8.2.1.
1.2The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
1.2.1Within the text the inch-pound units are shown in brackets.
1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health and environmental practices and determine the applicability of regulatory limitations prior to use.
1.4This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| Committee |
D 30
|
| DocumentType |
Standard Practice
|
| Pages |
6
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy |
| ASTM D 4762 : 2018 | Standard Guide for Testing Polymer Matrix Composite Materials |
| ASTM D 8509/D8509M : 2023 | Standard Guide for Test Method Selection and Test Specimen Design for Bolted Joint Related Properties |
| ASTM D 6484/D6484M : 2020 | Standard Test Method for Open-Hole Compressive Strength of Polymer Matrix Composite Laminates |
| ASTM D 3171 : 1999 | Standard Test Methods for Constituent Content of Composite Materials |
| ASTM D 7249/D7249M : 2018 | Standard Test Method for Facesheet Properties of Sandwich Constructions by Long Beam Flexure |
| ASTM E 177 : 1990 : REV A : R1996 | Standard Practice for Use of the Terms Precision and Bias in ASTM Test Methods |
| ASTM E 177 : 2014 : REDLINE | Standard Practice for Use of the Terms Precision and Bias in ASTM Test Methods |
| ASTM E 456 : 2002 | Standard Terminology for Relating to Quality and Statistics |
| ASTM D 3878 : 2002 : REV A | Standard Terminology for Composite Materials |
| ASTM D 6507 : 2019 | Standard Practice for Fiber Reinforcement Orientation Codes for Composite Materials |
| ASTM E 456 : 2013 : REV A : R2022 | Standard Terminology Relating to Quality and Statistics |
| ASTM D 5229/D5229M : 2014-06 | TEST METHOD FOR MOISTURE ABSORPTION PROPERTIES AND EQUILIBRIUM CONDITIONING OF POLYMER MATRIX COMPOSITE MATERIALS |
| ASTM D 3878 : 2015 | Standard Terminology for Composite Materials |
| ASTM D 3878 : 2019 | Standard Terminology for Composite Materials |
| ASTM D 3878 : 2000 | Standard Terminology Composite Materials |
| ASTM D 883 : 2022 | Standard Terminology Relating to Plastics |
| ASTM D 883 : 2020 : REV B | Standard Terminology Relating to Plastics |
| ASTM D 3171 : 2011 | Standard Test Methods for Constituent Content of Composite Materials |
| ASTM E 6 : 2002 | Standard Terminology Relating to Methods of Mechanical Testing |
| ASTM D 792 : 2013 : REDLINE | Standard Test Methods for Density and Specific Gravity (Relative Density) of Plastics by Displacement |
| ASTM E 456 : 2013 : REV A : R2017 : EDT 5 | Standard Terminology Relating to Quality and Statistics |
| ASTM D 6507 : 2016 : REDLINE | Standard Practice for Fiber Reinforcement Orientation Codes for Composite Materials |
| ASTM D 3410/D3410M : 2016 : REDLINE | Standard Test Method for Compressive Properties of Polymer Matrix Composite Materials with Unsupported Gage Section by Shear Loading |
| ASTM D 3878 : 2003 : REV A | Standard Terminology for Composite Materials |
| ASTM D 3878 : 2016 | Standard Terminology for Composite Materials |
| ASTM D 3410/D3410M : 2016 | Standard Test Method for Compressive Properties of Polymer Matrix Composite Materials with Unsupported Gage Section by Shear Loading |
| ASTM D 3878 : 2019 : REV A | Standard Terminology for Composite Materials |
| ASTM D 3878 : 2020 : REV A | Standard Terminology for Composite Materials |
| ASTM D 3878 : 1998 | Standard Terminology Composite Materials |
| ASTM D 3171 : 2022 | Standard Test Methods for Constituent Content of Composite Materials |
| ASTM D 3410/D3410M : 2016 : EDT 1 | Standard Test Method for Compressive Properties of Polymer Matrix Composite Materials with Unsupported Gage Section by Shear Loading |
| ASTM D 3878 : 2018 | Standard Terminology for Composite Materials |
| ASTM D 6507 : 2011 | Standard Practice for Fiber Reinforcement Orientation Codes for Composite Materials |
| ASTM D 6641/D6641M : 2016 : EDT 2 | Standard Test Method for Compressive Properties of Polymer Matrix Composite Materials Using a Combined Loading Compression (CLC) Test Fixture |
| ASTM E 132 : 2017 : REDLINE | Standard Test Method for Poisson’s Ratio at Room Temperature |
| ASTM D 3171 : 2009 | Standard Test Methods for Constituent Content of Composite Materials |
| ASTM D 3878 : 2002 | Standard Terminology for Composite Materials |
| ASTM D 6507 : 2016 | Standard Practice for Fiber Reinforcement Orientation Codes for Composite Materials |
| ASTM E 6 : 2015 : EDT 3 | Standard Terminology Relating to Methods of Mechanical Testing |
| ASTM E 6 : 2023 : REV A | Standard Terminology Relating to Methods of Mechanical Testing |
| ASTM D 3171 : 2015 : REDLINE | Standard Test Methods for Constituent Content of Composite Materials |
| ASTM D 3878 : 2004 | Standard Terminology for Composite Materials |
| ASTM D 3878 : 2007 : R2013 | Standard Terminology for Composite Materials |
| ASTM D 3878 : 2020 : REDLINE | Standard Terminology for Composite Materials |
| ASTM D 3878 : 2020 | Standard Terminology for Composite Materials |
| ASTM D 3878 : 2003 | Standard Terminology for Composite Materials |
| ASTM E 6 : 2015 : EDT 4 : REDLINE | Standard Terminology Relating to Methods of Mechanical Testing |
| ASTM D 6641/D6641M : 2016 : EDT 1 | Standard Test Method for Compressive Properties of Polymer Matrix Composite Materials Using a Combined Loading Compression (CLC) Test Fixture |
| ASTM D 3878 : 2007 | Standard Terminology for Composite Materials |
| ASTM D 6507 : 2000 : R2005 | Standard Practice for Fiber Reinforcement Orientation Codes for Composite Materials |
| ASTM D 6507 : 2000 | Standard Practice for Fiber Reinforcement Orientation Codes for Composite Materials |
| ASTM D 3171 : 1999 : R2004 | Standard Test Methods for Constituent Content of Composite Materials |
| ASTM D 695 : 2015 : REDLINE | Standard Test Method for Compressive Properties of Rigid Plastics |
| ASTM E 6 : 2015 : EDT 4 | Standard Terminology Relating to Methods of Mechanical Testing |
| ASTM D 3171 : 2015 | Standard Test Methods for Constituent Content of Composite Materials |
| ASTM E 6 : 2023 | Standard Terminology Relating to Methods of Mechanical Testing |
| ASTM E 456 : 2013 : REV A : R2017 : EDT 4 | Standard Terminology Relating to Quality and Statistics |
| ASTM E 456 : 2013 : REV A : R2017 : EDT 6 | Standard Terminology Relating to Quality and Statistics |
| ASTM D 3878 : 2004 : REV A | Standard Terminology for Composite Materials |
| ASTM D 3171 : 2006 | Standard Test Methods for Constituent Content of Composite Materials |
| ASTM D 6484/D6484M : 2014 : REDLINE | Standard Test Method for Open-Hole Compressive Strength of Polymer Matrix Composite Laminates |
| ASTM D 3878 : 2001 | Standard Terminology Composite Materials |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.