We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
  • ASTM E 1077 : 1991 : R1997

    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    Add to Watchlist
    This Standard has been added successfully to your Watchlist.
    Please visit My Watchlist to see all standards that you are watching.
    Please log in or to add this standard to your Watchlist.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    You need to be logged in to add this standard to your Watchlist.
    Please log in now or create an account to add.
    You already added this Product in the Watchlist.

    Standard Test Methods for Estimating the Depth of Decarburization of Steel Specimens

    Available format(s):  Hardcopy, PDF

    Superseded date:  11-11-2014

    Language(s):  English

    Published date:  31-12-2010

    Publisher:  American Society for Testing and Materials

    Add to Watchlist

    Add To Cart

    Scope - (Show below) - (Hide below)

    1.1 These test methods cover procedures for estimating the depth of decarburization of steels irrespective of the composition, matrix microstructure, or section shape. The following basic procedures may be used:

    1.1.1 Screening methods.

    1.1.2 Microscopical methods.

    1.1.3 Microindentation hardness methods.

    1.1.4 Chemical analysis methods.

    1.2 In case of a dispute, the rigorous quantitative or lineal analysis method (see 7.3.5 and 7.3.6) shall be the referee method. These methods can be employed with any cross-sectional shape. The chemical analytical methods generally reveal a greater depth of decarburization than the microscopical methods but are limited to certain simple shapes and by availability of equipment. These techniques are generally reserved for research studies. The microindentation hardness method is suitable for accurate measurements of hardened structures with relatively homogeneous microstructures.

    1.3 The values stated in SI units are to be regarded as standard. The inch-pound equivalents are in parentheses and may be approximate.

    1.4 This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

    General Product Information - (Show below) - (Hide below)

    Committee E 04
    Document Type Test Method
    Publisher American Society for Testing and Materials
    Status Superseded
    Superseded By

    Standards Referenced By This Book - (Show below) - (Hide below)

    ASTM B 874 : 1996 : R2018 Standard Specification for Chromium Diffusion Coating Applied by Pack Cementation Process
    ASTM A 295/A295M : 2014 : R2020 Standard Specification for High-Carbon Anti-Friction Bearing Steel
    ASTM A 756 : 2017 Standard Specification for Stainless Anti-Friction Bearing Steel
    ASTM B 848 : 2015 Standard Specification for Powder Forged (PF) Ferrous Materials
    ASTM A 295/A295M : 2014 Standard Specification for High-Carbon Anti-Friction Bearing Steel
    ASTM A 228/A228M : 2018 Standard Specification for Steel Wire, Music Spring Quality
    ASTM F 2282 : 2018 Standard Specification for Quality Assurance Requirements for Carbon and Alloy Steel Wire, Rods, and Bars for Mechanical Fasteners
    ASTM A 485 : 2017 Standard Specification for High Hardenability Antifriction Bearing Steel
    ASTM A 534 : 2017 Standard Specification for Carburizing Steels for Anti-Friction Bearings
    ASTM E 3 : 2011 : R2017 Standard Guide for Preparation of Metallographic Specimens
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective